National Instruments NI-5783 Getting Started Manual
  1. Manuals
  2. Brands
  3. National Instruments Manuals
  4. Control Unit
  5. NI-5783
  6. Getting started manual

National Instruments NI-5783 Getting Started Manual

Four channel transceiver adapter module
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
NI-5783

Advertisement

Table of Contents
loading

Related Manuals for National Instruments NI-5783

Summary of Contents for National Instruments NI-5783

  • Page 1 NI-5783...

  • Page 2: Table Of Contents

    GETTING STARTED GUIDE NI 5783 Four Channel Transceiver Adapter Module Before you begin, complete the software and hardware installation Note instructions in the getting started guide for your FlexRIO FPGA module or Controller for FlexRIO. The NI 5783 is a FlexRIO adapter module designed to work in conjunction with FlexRIO FPGA modules and Controllers for FlexRIO.

  • Page 3: Electromagnetic Compatibility Guidelines

    Furthermore, any modifications to the product not expressly approved by National Instruments could void your authority to operate it under your local regulatory rules.
  • Page 4 Available in NI Example Contains examples of how to run Finder. In LabVIEW, click FPGA VIs and Host VIs on your Help»Find Examples» device. Hardware Input and Output» FlexRIO. NI 5783 Getting Started Guide | © National Instruments | 3...

  • Page 5: Verifying The System Requirements

    Table 1. FlexRIO Documentation Locations and Descriptions (Continued) Document Location Description Located at ni.com/ipnet. IPNet Contains LabVIEW FPGA functions and intellectual property to share. FlexRIO product page Located at ni.com/flexrio. Contains product information and data sheets for FlexRIO devices. Verifying the System Requirements To use the NI 5783, your system must meet certain requirements.

  • Page 6: Installing The Ni 5783

    If the device is still not listed, power off the system, ensure the device is correctly installed, and restart. (Controllers for FlexRIO only) Your device appears under the Remote Devices section. NI 5783 Getting Started Guide | © National Instruments | 5...

  • Page 7: Recommended Cables

    Recommended Cables NI recommends using the following cables to connect signals to the NI 5783. Cable NI Part Number HDBNC to SMA 769177-01 HDBNC to BNC 769028-01 Accessories The NI 5783 can be used with the SCB-19 shielded desktop connector block. Refer to the SCB-19 User Guide for information about how to connect and use the SCB-19 with the AUX I/O front panel connector on your NI 5783.
  • Page 8 Connections that exceed any of the maximum ratings of any connector on Caution the NI 5783 can damage the device and the chassis. NI is not liable for any damage resulting from such connections. NI 5783 Getting Started Guide | © National Instruments | 7...

  • Page 9: Aux I/O Connector

    AUX I/O Connector Table 2. NI 5783 AUX I/O Connector Pin Assignments AUX I/O Connector Pin Signal Signal Description DIO Port 0 (0) Bidirectional single-ended (SE) digital I/O (DIO) data channel. Ground reference for signals. DIO Port 0 (1) Bidirectional SE DIO data channel. DIO Port 0 (2) Bidirectional SE DIO data channel.

  • Page 10: Block Diagram

    Typ: 4.6 W Abs Max: 5.5 W – Ch D+ RSS Max: 5.3 W 40 MHz AA LMH6702 Logic Diagram The following diagram shows the NI 5783 logic layout. NI 5783 Getting Started Guide | © National Instruments | 9...

  • Page 11: Component-Level Intellectual Property (Clip)

    Figure 2. NI 5783 Logic Layout User EEPROM Command Interface Microblaze Phase Status Reg Report Registers Data Clock 2x Clocking Sample Clock Data Clock 1/2 Samples Per Channel Oserdes Oserdes Output 1 Sample Per Channel Iserdes Iserdes Capture Component-Level Intellectual Property (CLIP) The LabVIEW FPGA Module includes component-level intellectual property (CLIP) for HDL IP integration.

  • Page 12: Ni 5783 400 Msps Ao Clip

    The following clock modes are available on the NI 5783. • Internal Sample Clock Free Running • Internal Sample Clock locked to an external Reference Clock through the CLK/REF IN front panel connector NI 5783 Getting Started Guide | © National Instruments | 11...
  • Page 13 • Internal Sample Clock locked to an external Reference Clock through Sync Clock • 60 MHz to 100 MHz external Sample Clock through the CLK/REF IN front panel connector Related Information Refer to the FlexRIO Help for more information about NI 5783 clocks. Worldwide Support and Services The NI website is your complete resource for technical support.
  • Page 14 LabVIEW FPGA Development Kit Module Help User Manual more about your products through ni.com. Support FlexRIO Services ni.com/support ni.com/flexrio ni.com/services *This item is also installed with the driver software. NI 5783 Getting Started Guide | © National Instruments | 13...
  • Page 15 CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS. U.S. Government Customers: The data contained in this manual was developed at private expense and is subject to the applicable limited rights and restricted data rights as set forth in FAR 52.227-14, DFAR 252.227-7014, and DFAR 252.227-7015. © 2016 National Instruments. All rights reserved. 375444A-01 Apr16...

Table of Contents