Installation - Pioneer DEH-P6100BT Installation Manual

Installation

English
DIN Front/Rear-mount
Note
This unit can be properly installed either from
• Check all connections and systems before final
"Front" (conventional DIN Front-mount) or
installation.
"Rear" (DIN Rear-mount installation, utilizing
• Do not use unauthorized parts. The use of
threaded screw holes at the sides of unit
unauthorized parts may cause malfunctions.
chassis). For details, refer to the following
• Consult with your dealer if installation requires
installation methods.
drilling of holes or other modifications of the
vehicle.
Removing or attaching
• Do not install this unit where:
— it may interfere with operation of the vehicle.
the trim ring
— it may cause injury to a passenger as a result
of a sudden stop.
1. Extend top and bottom of the trim
• The semiconductor laser will be damaged if it
ring outwards to remove the trim
overheats. Install this unit away from hot places
such as near the heater outlet. ring.
• Optimum performance is obtained when the unit is
• When reattaching the trim ring, push the trim
installed at an angle of less than 60°.
ring onto the unit until it clicks. (If the trim
ring is attached upside down, the trim ring will
not fit properly.)
• It becomes easy to remove the trim ring if the
60°
front panel is released.
Trim ring
• When installing, to ensure proper heat dispersal
when using this unit, make sure you leave ample
space behind the rear panel and wrap any loose
cables so they are not blocking the vents.
Dashboard
Leave ample space
10cm (3-7/8 in.)
10cm (3-7/8 in.)
Installation English
DIN Front-mount Removing the Unit
1. Insert the supplied extraction keys
Installation with metal strap and
into both sides of the unit until
screws
they click into place.
1. Insert the mounting sleeve into the
dashboard.
• When installing in a shallow space, use a
supplied mounting sleeve. If there is enough
space behind the unit, use factory supplied
mounting sleeve.
2. Secure the mounting sleeve by
using a screwdriver to bend the
metal tabs (90°) into place.
Mounting sleeve
Dashboard
182
53
2. Pull the unit out of the dashboard.
DIN Rear-mount
3. Install the unit.
• Use commercially available parts when
1. Determine the appropriate position
installing.
where the holes on the bracket and
Nut
the side of the unit match.
Firewall or
metal support
Metal strap
Screw
2. Tighten two screws on each side.
Screw (M4 8)
• Use either truss screws (5 mm × 8 mm)
or flush surface screws (5 mm × 9 mm),
depending on the shape of screw holes in the
bracket.
• Make sure that the unit is installed securely
in place. Unstable installation may cause this
unit to malfunction, such as sound skip.
Dashboard or Console
Factory radio mounting bracket
Installation
Fastening the front panel Installing the microphone
If you do not plan to detach the front panel,
Installation notes
the front panel can be fastened with supplied
Install the microphone in a position and
screw.
orientation that will enable it to pick up the
voice of the person operating the system.
CAUTION
• It is extremely dangerous to allow the microphone
Screw
lead to become wound around the steering
column or gearstick. Be sure to install the unit in
such a way that it will not obstruct driving.
When installing the microphone
on the sun visor
1. Install the microphone on the
microphone clip.
• Microphone can be installed without using
microphone clip. In this case, detach the
microphone base from the microphone
clip. To detach the microphone base from
microphone clip, slide the microphone base.
Screw
English Installation
2. Install the microphone clip on the
sun visor.
• With the sun visor up, install the microphone
clip. (Lowering the sun visor reduces the voice
recognition rate.)
Microphone clip
Clamp
Use separately sold
clamps to secure the
lead where necessary
inside the vehicle.
Microphone
When installing the microphone
Microphone clip
on the steering column
Microphone base
1. Install the microphone on the
microphone clip.
Microphone
Fit the
microphone lead
into the groove.
Microphone clip
English
2. Install the microphone clip on the
steering column.
Double-sided tape
Install the microphone clip on the
rear side of the steering column.
Clamp
Use separately sold
clamps to secure the
lead where necessary
inside the vehicle.
Adjusting the microphone
angle
The microphone angle can be adjusted.