Operation - Monacor 0257760 Instruction Manual

SA-130DMP
➀
1 2
➁
tape deck, radio, mixer, PC), two inputs are
available:
– 3 .5 mm jack AUX (3);
when this jack is connected, the combi-
nation "MP3 player / FM radio / Bluetooth
receiver" will be muted .
– RCA jacks LINE IN (10);
L (white) = left, R (red) = right
3) The stereo connections PRE OUT and AMP
IN (11) can be used to insert an audio pro-
cessing unit (e . g . equalizer, effect unit):
The signal, after the control VOLUME (8),
will be routed to the audio processing unit
via the output PRE OUT and returned to the
power amplifier of the SA-130DMP via the
input AMP IN .
a) Remove the two jumpers (one each for
the left channel and the right channel)
that interconnect the output PRE OUT
and the input AMP IN .
b) Connect the input of the unit to be in-
serted to the output PRE OUT .
c) Connect the output of the unit to be
inserted to the input AMP IN .
4) Connect two speakers (minimum im-
pedance: 4 Ω) to the terminals SPEAKER
OUT (12): Connect one speaker to the
channel RIGHT and the other to the chan-
nel LEFT . Observe the polarity (connect the
marked core of the respective speaker cable
to "+") . Use either the screw terminals or
the banana jacks to make the connections .
Note: When connecting more than two speakers,
make sure that the total speaker impedance per
channel is at least 4 Ω; otherwise, the amplifier
may be damaged . Contact an expert if you have
any questions .
5) When the integrated FM radio is used,
connect an FM antenna to the jack FM
ANTENNA (14) .
6) For power supply, connect the mains cable
provided to the mains jack (13) first and
then to a mains socket (230 V/ 50 Hz) .

6 Operation

CAUTION Never adjust the amplifier to a
very high volume . Permanent
high volumes may damage your
hearing!
To prevent switching noise, always switch on
the units connected before switching on the
amplifier and always switch off the amplifier
before switching off the other units .
8
3
10 11
1) Before switching on the amplifier for the
first time, turn the total volume control
VOLUME (8) to the left stop .
2) Use the POWER switch (1) to switch on the
amplifier .
3) Turn up the control VOLUME (8) to adjust
the total volume desired; for each audio
source to be heard, adjust the volume by
means of the appropriate control:
– control MIC LEVEL (5) for the microphone
connected to the input MIC (2)
– control LINE LEVEL (7) for the unit con-
nected to the input LINE IN (10)
– control AUX / MP3 LEVEL (6) for the unit
connected to the input AUX (3) or, when
the input AUX is not used, for the combi-
nation "MP3 player / FM radio /Bluetooth
receiver" (4)
Note: The basic volume of the combination
"MP3 player / FM radio / Bluetooth receiver" can
be additionally adjusted: see chapter 6 .1 .3 .
4) Use the controls TREBLE and BASS (9) to
adjust the tone .
6.1 MP3 player / FM radio /
Bluetooth receiver (fig . 3)
When the SA-130DMP is switched on, the
combination "MP3 player / FM radio / Bluetooth
receiver" will automatically be activated and
go to the mode "Player" . When no storage
medium is connected,
on the display (16) . When a storage medium
is already connected, it will be read and then
reproduced . When two storage media are con-
nected, the USB medium will be selected after
the SA-130DMP has been switched on .
The infrared remote control is operated with
a battery . If a battery is already inserted in the
remote control, remove the insulating film (to
protect the battery from being discharged)
from the battery holder . After that, the remote
control is ready for operation . When pressing
a button, always point the remote control to
the infrared sensor (15) . Make sure that there
are no obstacles between the remote control
and the sensor .
If the remote control is not used for a
longer period of time, remove the battery as a
precaution so that the remote control will not
be damaged in case the battery should leak .
Inserting / Replacing the battery:
1) Push the latch of the battery holder to the
right (first arrow in figure 4) and pull out
the holder (second arrow) .
4
12
will appear
NO SOURCE
5 6 7 8
2) To replace a battery, remove the discharged
battery .
3) Insert a new battery (3 V button cell, type
CR 2025) in the holder, positive pole facing
upwards . Push the holder back into the re-
mote control .
➃
1. 2.
Never put batteries in the household
waste . Always dispose of the batteries
in accordance with local regulations .
6.1.1 Standby
To set the combination "MP3 player / FM radio /
Bluetooth receiver" to the standby mode and
to switch it on again, either use the button
(26) on the remote control or keep the button
MODE (21) at the unit pressed for more than
a second . After switch-on, the mode "Player"
will be active .
6.1.2 Selecting the operating mode
Use the button MODE (21) to switch over be-
tween the operating modes:
"Player""Bluetooth""Radio" 
When two storage media are connected in the
mode "Player": The first press of the button
MODE will switch to the storage medium cur-
rently not selected; the next press of the button
will switch to the mode "Bluetooth" .
6.1.3 Adjusting the basic volume /
Muting
To adjust the basic volume (adjustment range
to ), use the buttons
00 31
the remote control or keep the button
or (24) at the unit pressed .
I

To mute the sound, press the button
(27); will appear on the display . To
MUTE
unmute the sound, press the button again .
Note: When the mute function is activated, it will
be deactivated after the next switch-on or when the
operating mode is changed .
6.1.4 Operating mode "Player"
The player can be used to reproduce MP3 files
from SD / SDHC memory cards and USB storage
media (USB flash drive or USB hard disk with
separate power supply) . The reproduction of
WMA files and WAV files is also supported .
– Connect a USB storage medium to the USB
port (17) .
– Insert a memory card (FAT16 / FAT32, 32 GB
max .), notched corner facing to the right and
9
13 14
and (28) on
I
