Related Manuals for SeaLevel REL-16 3095
Summary of Contents for SeaLevel REL-16 3095
- Page 1 ™ REL-16 USER’S MANUAL Part Number 3095 Sealevel Systems, Inc Phone: (864) 843-4343 155 Technology Place Fax: (864) 843-3067 P.O. Box 830 www.sealevel.com Liberty, SC 29657...
-
Page 2: Table Of Contents
Contents ................1 NTRODUCTION ....................1 VERVIEW ’ ..................1 NCLUDED ..............1 ACTORY EFAULT ETTINGS ..................2 ETUP ..................2 DDRESS ELECTION .................3 NSTALLATION ................3 OFTWARE NSTALLATION For Windows Users................3 .............4 ECHNICAL ESCRIPTION ....................4 EATURES ) ..............5 UTPUT ORTS ELAY... - Page 3 ......16 EDERAL OMMUNICATIONS OMMISSION TATEMENT EMC D ..............16 IRECTIVE TATEMENT ..................17 ARRANTY Figures Figure 1 - Address Selection Table..............2 Figure 2 - DIP-Switch Illustration..............2 ©2002a Sealevel Systems, Incorporated. All rights reserved.
-
Page 4: Introduction
Factory Default Settings The REL-16 factory default settings are as follows: Base Address To install the REL-16 using factory default settings, refer to Installation on page 3. For your reference, record installed REL-16 settings below: Base Address Sealevel Systems REL-16 Page 1... -
Page 5: Card Setup
1. O F F Figure 2 - DIP-Switch Illustration Note: Setting the switch ‘On’ or ‘Closed’ corresponds to a ‘0’ in the address, while leaving it ‘Off’ or ‘Open’ corresponds to a ‘1’. Sealevel Systems REL-16 Page 2... -
Page 6: Installation
Replace the cover. 6. Connect the power cord. Installation is complete. Software Installation For Windows Users Choose Install Software at the beginning of the CD and select the Digital I/O software drivers and install SeaIO. Sealevel Systems REL-16 Page 3... -
Page 7: Technical Description
DB-37 male connector for relay outputs • Highly reliable 10 VA DIP reed relays utilized • 8 bit slot connector • Multiple adapters can reside in same computer • All address, data and control signals are TTL compatible Sealevel Systems REL-16 Page 4... -
Page 8: Output Ports (Reed Relay)
Contact Resistance, Initial: .15 Ohms • Rated Life: Low Load: 200 Million Closures Maximum Load: 100 Million Closures • Contact Speed: Operate: .5 m Sec Release: .5 m Sec Bounce: .5 m Sec • Maximum Operating Speed: 600 Hertz Sealevel Systems REL-16 Page 5... -
Page 9: Output Ports (Reed Relay) Pin Assignments (P2)
Output Ports (Reed Relay) Pin Assignments (P2) Port C Relay P2 Pin Port D Relay P2 Pin 2,20 10,28 3,21 11,29 4,22 12,30 5,23 13,31 6,24 14,32 7,25 15,33 8,26 16,34 9,27 17,35 Ground 18,36,37 + 5 Volts + 12 Volts Sealevel Systems REL-16 Page 6... -
Page 10: Programming
) input port of the device will be utilized. In all addressing modes, port numbers are zero-indexed; that is, the first port is port #0, the second port is #1, the third #2, and so on. Sealevel Systems REL-16 Page 7... - Page 11 11 ( W ) 28 ( R/W ) 12 ( W ) 29 ( R/W ) 13 ( W ) 30 ( R/W ) 14 ( W ) 31 ( R/W ) 15 ( W ) Sealevel Systems REL-16 Page 8...
-
Page 12: Direct Hardware Control
R/W = Read or Write Function Port Address Hex Address Port Type Available Decimal 300 (Base + 0) Unused 301(Base + 1) Unused 302 (Base + 2) Output Port (Reed Relays) 303 (Base + 3) Output Port Sealevel Systems REL-16 Page 9... -
Page 13: Specifications
Greater than 150,000 hours. (Calculated) Physical Dimensions Board length 4.9 inches (12.45 cm) Board Height including Goldfingers 4.2 inches (10.66 cm) Board Height excluding Goldfingers 3.9 inches (9.906 cm) Note: Please see Appendix D for board layout and dimensions. Sealevel Systems REL-16 Page 10... -
Page 14: Appendixa - Troubleshooting
1. Identify all I/O adapters currently installed in your system. This includes your on-board serial ports, controller cards, sound cards etc. 2. Configure your Sealevel Systems adapter so that there is no conflict with currently installed adapters. No two adapters can occupy the same I/O address. -
Page 15: Appendixb - How T O Get Assistance
3. Technical support is available Monday to Friday from 8:00 a.m. to 5:00 p.m. Eastern time. Technical support can be reached at (864) 843-4343. RETURN AUTHORIZATION MUST BE OBTAINED FROM SEALEVEL SYSTEMS BEFORE RETURNED... -
Page 16: Appendixc - Silk -Screen
Appendix C - Silk-Screen Appendix C - Silk-Screen Sealevel Systems REL-16 Page 13... -
Page 17: Appendixd - Schematic
Appendix D - Schematic Appendix D - Schematic Sealevel Systems REL-16 Page 14... - Page 18 Appendix D - Schematic Sealevel Systems REL-16 Page 15...
-
Page 19: Appendixe - Compliance Notices
Always use cabling provided with this product if possible. If no cable is provided or if an alternate cable is required, use high quality shielded cabling to maintain compliance wi th FCC/EMC directives. Sealevel Systems REL-16 Page 16... - Page 20 Sealevel Systems, Inc. provides a lifetime warranty for this product. Should this product fail to be in good working order at any time during this period, Sealevel Systems will, at it's option, replace or repair it at no additional charge except as set forth in the following terms.