Finishing; Connection Pipe, Cable And Drain Hose; Front Panel Removal And Installation; Intake Grill Removal And Installation - Fujitsu AIRSTAGE ASUA36TLAV2 Installation Manual

7. FINISHING

After checking for gas leaks (refer to the Installation Manual of the outdoor unit), perform
this section.
Install heat insulation around both the large (gas) and small (liquid) pipes. Failure to do
so may cause water leaks.

7.1. Connection pipe, cable and drain hose

Insulate the drain hose, if necessary, to prevent it from freezing.
(1) Insulate between pipes.
• For (A) Rear, (B) Right and (C) Bottom piping, overlap the connection pipe heat insula-
tion and indoor unit pipe heat insulation and bind them with vinyl tape so that there is no
gap.
• For (D) Left bottom piping, (E) Left piping, (F) Center piping and (G) Left rear piping, butt
the connection pipe heat insulation and indoor unit pipe heat insulation together and bind
them with vinyl tape so that there is no gap.
((A) Rear, (B) Right and (C) Bottom piping)
Connection pipe
(heat insulation)
Bind the pipes together so
that there is no gap.
(For (D) Left bottom piping, (E) Left piping, (F) Center piping and (G) Left rear piping)
• Wrap the area which accommodates the rear piping housing section with cloth tape.
• Bind the connection cable with vinyl tape.
• Bundle the piping and drain hose together by wrapping them with cloth tape over the
range within which they fit into the rear piping housing section.
Connection pipe
Cloth tape
(accessories)
Connection cable (power supply cable)
Connection cable (Transmission and Remote controller cable)
Pipe
Drain hose
(2) Temporarily fasten the connection cable along the connection pipe with vinyl tape.
(3) Fasten the connection pipe to the outside wall with a saddle, etc.
(4) Fill the gap between the outside wall pipe hole and the pipe with sealer so that rain
water and wind cannot blow in.
(5) Fasten the drain hose to the outside wall, etc.
Saddle*
Pipe
GOOD
Drain
hose
Lifted up
Saddle
En-13
CAUTION
Overlap the insulation.
Indoor unit pipe
(heat insulation)
Vinyl tape
Indoor unit pipe
Wrap with cloth tape.
Pipe
Vinyl tape
Wrap with cloth tape
Cloth tape
Outside wall cap*
Sealer putty*
Wall
(Outdoors)
*Locally purchased
PROHIBITED
Wave End in water

8. FRONT PANEL REMOVAL AND INSTALLATION

8.1. Intake grill removal and installation

Intake grill removal
Open the intake
grille. While gently
pressing the left and
right mounting shafts
of the intake grille
b
outward "a", remove
the intake grille in
direction of the ar-
row "b".
Press 4 places on the intake grille to close it com-
pletely.

8.2. Front panel removal

(1) Remove 4 caps, remove
wire cover and remove
10 screws.
NOTES:
When replacing the front
panel, do not scratch or dam-
age the louver.
(2) The front panel is pulled
to the front, raising the
upper surface, then the
front panel is removed.

8.3. Front panel installation

(1) First, fit the lower part of the front panel, and insert top and middle hooks. (3 top
sides, 5 middles)
Top holes (3 position)
Middle hooks
Indoor unit
(5 position)
(2) Attach the 10 screws.
(3) Attach the wire cover.
(4) Attach the 4 caps.
Intake grill installation
While holding the
grille horizontal, set
the left and right
mounting shafts into
a
the pillow blocks
at the top of the
c
panel "c". To latch
each shaft properly,
insert the shaft until
it snaps.
Screws (Wire cover)
Screws
(10 position)
Caps (4 position)
Top hooks
(3 position)
Front panel
Middle hooks
(5 position)
Wire cover
Front panel