Assembly - Dolmar TM-102.17 H Instruction Manual

Instructions for maintenance and storage
4.
4.1 Make sure that the nuts, bolts and screws are tight.
4.2 Be careful when adjusting - danger of injuries. Do not trap your
fingers between the housing and the blade. Wear protective gloves.
4.3 Never store the lawn tractor with fuel in the tank inside a building in
which petrol fumes can possibly come into contact with naked
flames or with sparks
- danger of explosion!
4.4 Only empty the petrol tank in the open.
4.5 Allow the engine to cool down before you put the machine into an
enclosed area.
4.6 Avoid the risk of a fire by keeping the engine and the exhaust free
of grass, leaves and grease (oil).
4.7 Check regularly to make sure that the grass box is in a satisfactory
condition.
4.8 For safety's sake, worn or damaged parts must be replaced
immediately.
4.9 Replacement blades and additional appliances may only be
mounted on the lawn tractors intended for this purpose according to
the manufacturer's instructions. This is the only way to maintain the
safety and the performance of your lawn tractor.
4.10 Please ensure that the maintenance, checking and sharpening of
the blade is only done by an authorised dealer.
4.11 Only use original replacement blades.
We would point out that we are not liable according to the Product
Liability Act for damage caused by our machine as a result of
improper repairs not carried out by our authorised service
a)
agents,
or if ORIGINAL SPARE PARTS are not used as replacement
b)
parts.
The same applies to accessories. A service booklet with the
addresses of our authorised service agents is enclosed with the
appliance.
GB

ASSEMBLY

The following assembly work must be carried out before the first
operation:
1. Installation of the steering wheel.
2. Installation of the driver's seat.
3. Assembly of the grass box
4. Fitting the grass box to the lawn tractor.
Attention!
Putting into operation (even test operation) before complete
assembly is strictly forbidden - dangers of accidents!
The information on directions (right, left, top etc.) for this appliance
are to be understood in the direction of travel looking from the
driver's seat.
The order of assembly steps is to be complied with, as otherwise
flawless function cannot be guaranteed.
Please note:
The figures stated to the left of the text, such as the
here, refer to the illustrations in the illustrated part at the front.
Assembly of the steering wheel
Point the front wheels straight ahead in the direction of
1
movement.
Push the 8 x 60 ∅ clamping sleeve about 10 mm into the
bore of the steering wheel hub.
Put the steering wheel onto the steering column.
Ensure the correct position: the spoke is to point towards
the driver's seat.
Put the round iron (7 x 150 mm ∅) of the enclosed spark
plug connector into the free bore of the steering wheel hub.
Turn the steering wheel until the round iron can be pushed
through the bore of the steering wheel.
Connect with steering wheel with the steering column by
pushing in the 8 x 60 ∅ clamping bolt.
Installing the driver's seat
2
Unscrew the driver's seal according to the diagram on the
hinged console.
Hexagonal recess hole screw M8 x 20
Fan-disk Ø 8.4 x Ø 15
Disk Ø 8.4 x Ø 24
Spacer bushing Ø 8.2 x Ø 14
Hexagonal recess hole screw /
Wing screw M8 x 20
Fan-disk Ø 8.4 x Ø 15
Push the seat into the required position and tighten the
screws by means of the enclosed socket wrench – 6 mm
(Allen key)!
The seat can be moved in a longitudinal direction by
loosening the screw
GB 8
10
(2 x)
(2 x)
(2 x)
(2 x)
(2 x)
(2 x)
.