HIKVISION DS-TDSB00-EKT/POE/4M User Manual

HIKVISION DS-TDSB00-EKT/POE/4M User Manual

Fall detection radar

Advertisement

Fall Detection Radar
User Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DS-TDSB00-EKT/POE/4M and is the answer not in the manual?

Questions and answers

Summary of Contents for HIKVISION DS-TDSB00-EKT/POE/4M

  • Page 1 Fall Detection Radar User Manual...
  • Page 2 WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES,...
  • Page 3 Fall Detection Radar User Manual DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES.
  • Page 4 Fall Detection Radar User Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Indicates a hazardous situation which, if not avoided, will or could Danger result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could Caution result in equipment damage, data loss, performance degradation, or...
  • Page 5: Table Of Contents

    Fall Detection Radar User Manual Contents Chapter 1 Introduction ....................... 1 1.1 Product Introduction ......................1 1.2 Key Feature ..........................1 Chapter 2 Activation and Login ....................2 2.1 Activation ..........................2 2.1.1 Default Information ...................... 2 2.1.2 Activate via SADP ......................2 2.1.3 Activate via Web Browser .....................
  • Page 6 Fall Detection Radar User Manual Chapter 6 Exception Alarm ....................... 16 Chapter 7 Safety Management ....................17 7.1 Manage User ........................17 7.2 Enable User Lock ........................17 7.3 Install Authorized Certificate ....................18 7.4 Create and Install Self-signed Certificate ................18 7.5 Set SSH ..........................
  • Page 7: Chapter 1 Introduction

    Fall Detection Radar User Manual Chapter 1 Introduction 1.1 Product Introduction Fall detection radar (hereinafter referred to as "device") adopts FMCW, MIMO, beamforming, KNN, and other technologies. It can obtain target information, including person location, speed, posture, etc., and can provide non-contact fall detection. 1.2 Key Feature Supports to follow the target and output the real-time location information.
  • Page 8: Chapter 2 Activation And Login

    Get the SADP software from the supplied disk or the official website ( http:// ● www.hikvision.com/ ), and install it according to the prompts. The device and the computer that runs the SADP tool should belong to the same network ●...
  • Page 9: Activate Via Web Browser

    Fall Detection Radar User Manual Figure 2-1 Activate via SADP Status of the device becomes Active after successful activation. 5. Modify IP address of the device. 1) Select the device. 2) Change the device IP address to the same network segment as your computer by either modifying the IP address manually or checking Enable DHCP (Dynamic Host Configuration Protocol).
  • Page 10: Login

    Fall Detection Radar User Manual Caution STRONG PASSWORD RECOMMENDED-We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.
  • Page 11: Chapter 3 Radar Detection

    Fall Detection Radar User Manual Chapter 3 Radar Detection Enter a short description of your concept here (optional). This is the start of your concept. 3.1 Set Radar Mode Set radar mode according to the actual needs. Steps 1. Go to Configuration → System → System Settings → Radar . Figure 3-1 Set Radar Mode 2.
  • Page 12: Set Detection Parameters

    Fall Detection Radar User Manual 3.2 Set Detection Parameters Set radar detection parameters according to the actual needs and installation environment. Steps 1. Click Falling Monitoring. Figure 3-2 Set Detection Parameters 2. View the radar information. Radar Status The current radar status. The radar can be normally used in normal status. If the radar is in upgrading status, do not reboot the device.
  • Page 13: Chapter 4 Storage

    Fall Detection Radar User Manual Chapter 4 Storage 4.1 Set SDK Listening The SDK listening can be used to receive the uploaded information of the device arming alarm. Before You Start The listening service has been enabled for the SDK listening, and the network communication with the device is normal.
  • Page 14: Chapter 5 Network Configuration

    Fall Detection Radar User Manual Chapter 5 Network Configuration 5.1 Set IP Address IP address must be properly configured before you operate the device over network. IPv4 and IPv6 are both supported. Both versions can be configured simultaneously without conflicting to each other.
  • Page 15 Fall Detection Radar User Manual Select a NIC (Network Interface Card) type according to your network condition. IPv4 Two modes are available. DHCP The device automatically gets the IP parameters from the network if you check DHCP. The device IP address is changed after enabling the function. You can use SADP to get the device IP address.
  • Page 16: Set Wi-Fi

    Fall Detection Radar User Manual 5.2 Set Wi-Fi Set Wi-Fi parameters if you want to connect the device to the network via Wi-Fi. Steps 1. Go to Configuration → Network → Network Parameters → Wi-Fi . 2. Select Wi-Fi Mode as Wi-Fi. 3.
  • Page 17: Connect To Platform

    Fall Detection Radar User Manual 5.4 Connect to Platform 5.4.1 Connect to OTAP The device can be accessed to the maintenance platform via OTAP protocol, in order to search and acquire device information. Before You Start Ensure the device can communicate with the platform normally. Steps 1.
  • Page 18: Connect To Hik-Connect

    Fall Detection Radar User Manual 5.4.2 Connect to Hik-Connect The device can be remotely accessed via Hik-Connect. Before You Start Connect the device to the Internet. ● Set the IP address, subnet mask, gateway, and DNS server of the LAN. ●...
  • Page 19: Set Snmp

    Fall Detection Radar User Manual Figure 5-3 Set DDNS 3. Enter the server address, domain, and other information. 4. Click Save. 5. Optional: Enter the domain name in the browser address bar to access the device. 5.6 Set SNMP You can set the SNMP network management protocol to get the alarm event and exception messages in network transmission.
  • Page 20: Set Ieee 802.1X

    Fall Detection Radar User Manual 5.7 Set IEEE 802.1X IEEE 802.1X is a port-based network access control. It enhances the security level of the LAN/ WLAN. When devices connect to the network with IEEE 802.1X standard, the authentication is needed. Steps 1.
  • Page 21 Fall Detection Radar User Manual It refers to the port through which the browser accesses the device. For example, when the HTTP Port is modified to 81, you need to enter http://192.168.1.64:81 in the browser for login. HTTPS Port It refers to the port through which the browser accesses the device, but certificate verification is needed.
  • Page 22: Chapter 6 Exception Alarm

    Fall Detection Radar User Manual Chapter 6 Exception Alarm Set exception alarm when the network is disconnected, the IP address is conflicted, etc. Steps 1. Go to Configuration → Event → Alarm Linkage → Exception . 2. Select the exception type(s) according to the actual needs. 3.
  • Page 23: Chapter 7 Safety Management

    Fall Detection Radar User Manual Chapter 7 Safety Management 7.1 Manage User The administrator can add, modify, or delete other accounts, and grant different permissions to different user levels. Steps 1. Go to Configuration → System → User Management . 2.
  • Page 24: Install Authorized Certificate

    Fall Detection Radar User Manual 7.3 Install Authorized Certificate If the demand for external access security is high, you can create and install authorized certificate via HTTPS protocol to ensure the data transmission security. Steps 1. Go to Configuration → Network → Network Parameters → HTTPS . 2.
  • Page 25: Set Ip Address Filtering

    Fall Detection Radar User Manual 3. Click Save. 7.6 Set IP Address Filtering You can set the IP addresses allowable and not allowable to access the device. Steps 1. Go to Configuration → System → Security → Security Settings . 2.
  • Page 26 Fall Detection Radar User Manual - Select Permanent. The password will be permanently valid. - Select Daily and set Password Expiry Time. It will prompt you that the password is expired according to the set password expiry time, and you need to set the new password. 3.
  • Page 27: Chapter 8 Maintenance

    Fall Detection Radar User Manual Chapter 8 Maintenance 8.1 View Device Information Basic Information and Algorithms Library Version Go to Configuration → System → System Settings → Basic Information to view the basic information of the device. You can edit Device Name and Device No. The device No. is used to control the device. It is recommended to reserve the default value.
  • Page 28: Upgrade

    Fall Detection Radar User Manual 3. Click Save. 8.3 Upgrade Upgrade the system when you need to update the device version. Before You Start Prepare the upgrade file. If the upgrade file is a compressed package, it needs to be decompressed into the .dav format.
  • Page 29: Set Serial Port

    Fall Detection Radar User Manual Steps 1. Go to Configuration → System → Maintenance → Upgrade & Maintenance → Device Maintenance . 2. Select the restoration mode. - Click Restore and click OK. Then the parameters except the IP parameters, user parameters, and the saved parameters will be restored to the default settings.
  • Page 30: Set Dst

    Fall Detection Radar User Manual Steps 1. Go to Configuration → System → System Settings → Time Settings . 2. Select Time Zone. 3. Select Sync Mode. NTP Synchronization Select it to synchronize the device time with that of the NTP server. Set Server IP, NTP Port, and Interval.
  • Page 31: Import Configuration File

    Fall Detection Radar User Manual 2. Click Export after Configuring Parameters. 3. Set an encryption password, confirm the password, and click OK. Note The password is used for importing the configuration file of the current device to other devices. 4. Select the saving path, and enter the file name. 5.
  • Page 32: Export Diagnosis Information

    Fall Detection Radar User Manual 8.12 Export Diagnosis Information The technicians can export the diagnosis information to troubleshoot and maintain the device. Steps 1. Go to Configuration → System → Maintenance → Upgrade & Maintenance → Data Export . 2. Click Export after Diagnosis Information. 3.
  • Page 33: Appendix A. Communication Matrix And Device Command

    Fall Detection Radar User Manual Appendix A. Communication Matrix and Device Command Scan the QR code below to get the communication matrix of the device. Scan the QR code below to get the device command.
  • Page 34 UD31949B...

This manual is also suitable for:

Ds-tdsb00-ekh/poe/2m

Table of Contents