Subscribe to Our Youtube Channel
Related Manuals for Total Source KRIH0001
Summary of Contents for Total Source KRIH0001
- Page 1 Original operating manual OPERATING MANUAL FORKLIFT JACK K R I H 0 0 01 - K R I H 0 0 0 2 - K R I H 0 0 0 3 06/2021 - V01...
- Page 2 © 06 -2021. TVH and TotalSource are registered trademarks. TVH Parts Holding NV, Brabantstraat 15, B-8790 Waregem. All rights reserved. ® ® No part of this publication may be reproduced or communicated in any form or by any means, electronic or mechanical, including copying, recording or use in an information storage or retrieval system, without prior and explicit permission of TVH Parts Holding NV.
- Page 3 Bulgare Можете да намерите това ръководство на Вашия език чрез линка, посочен по – долу. Tchèque Tento návod najdete ve svém jazyce prostřednictvím odkazu níže. Danois Du kan finde denne vejledning på dit sprog via nedenstående link. Allemand Sie finden diese Bedienungsanleitung in Ihrer Sprache unter folgendem Link. Grec Μπορείτε...
- Page 4 Thank you for using our product. For your safety and to ensure a correct operation, we would like to bring to your attention some aspects of this manual: • This booklet provides useful instructions for the correct operation and maintenance of the product.
-
Page 5: Table Of Contents
TABLE OF CONTENTS INTRODUCTION ..................DESCRIPTION . -
Page 6: Introduction
INTRODUCTION This manual contains all the necessary information about the installation and operation of the forklift jack. Some of the maintenance operations should only be carried out by professional technicians. If you need this information and the maintenance steps, please contact your dealer. Also included in this manual are a number of safety instructions to create a safe working environment. -
Page 7: Description
DESCRIPTION 2.1. Technical data Always check the data plate for the correct information. Type Forklift jack KRIH0001 Lifting capacity (kg) 4000 Minimum lifting height of the foot (mm) (H3/H4) Maximum lifting height of the saddle (mm) (H3/ Width of the base (mm) (H1/H2) -
Page 8: Main Components Of The Product
2.2. Main components of the product N° Component Grip handle Lever Return valve Wheels Lifting foot 2.3. Type plate N° Plaque signalétique Explication Type of product Serial number Type of pallet truck xxxx Fork length xxxx mm Capacity of the product (kg) Serial n°... -
Page 9: Safety Instructions
SAFETY INSTRUCTIONS 3.1. Explanation of the safety decals If the decals are damaged or missing, please replace them. N° Autocollant Explication 1. The wheels must be locked before using the 166TA4352 jack. 2. The jack shall be placed in its intended position under the vehicle. - Page 10 • TVH Parts Holding NV can’t anticipate all possible circumstances that might result in danger. Therefore, the warnings given in this publication, and those that appear on the equipment, are not exhaustive. • In the event that equipment, procedures, work methods or working techniques are used that are not specifically advised by the TVH Parts Holding NV company, it must be ensured that there is no danger to the operator or other people.
-
Page 11: Transport And Storage
TRANSPORT AND STORAGE The forklift jack must always be stored level, in a dry and temperature-controlled environment. Transport the jack to the work area by either (a) wheeling it or (b) lifting and carrying it. The jack should always be wheeled to the work area if possible—only lift and carry the jack if it can’t be wheeled safely. - Page 12 How to lift and carry the jack 1. Determine the lifting points on the jack (see Figure 3). The jack should be lifted using the lifting point at the toe end. Never lift the jack by the pump handle. The pump handle can’t carry sufficient weight.
-
Page 13: Assembly And Installation
ASSEMBLY AND INSTALLATION 5.1. Packing list KRIH0001 Description Amount Reference Handle 144TA9612 Jack Contact your dealer Bolt 144TA9609 /144TA9610 Operating manual 166TA8327 KRIH0002 Description Amount Reference Handle Contact your dealer Jack Contact your dealer Bolt Contact your dealer Operating manual... -
Page 14: Operation
OPERATION 6.1. Safety instructions • Keep the work area well illuminated. • Make sure that the forklift jack makes firm contact with the ground. • When the forklift jack is in use, make sure that no persons are in the vicinity of the forklift jack or lie down underneath the vehicle to prevent serious injuries. -
Page 15: Operating Instructions
6.2. Operating instructions Carry out the daily maintenance check listed in chapter 7. 1. Apply the emergency brake on your vehicle and turn each non-lifted wheel in the opposite direction to prevent unintended vehicle movements; 2. Close the release valve by turning it clockwise. You must feel a firm resistance. - Page 16 6. Immediately after transferring the load, place the support stands under the machine. The support stands should be as widely spaced as possible! If you place the support stands too close together, the vehicle is more likely to tip over. Lowering 1.
- Page 17 3. Slowly turn the release valve counterclockwise, but no more than half a turn. 4. Remove the jack. Fully lower the saddle and push the handle sleeve down. This to reduce exposure to the piston to prevent rust and pollution. 17/32...
-
Page 18: Maintenance
MAINTENANCE 7.1. Safety instructions for the repair of the product If you need the hydraulic diagram or the spare parts list, please contact your dealer. Some of the maintenance operations should only be carried out by professional technicians. If you need this information and the maintenance steps, please contact your dealer. •... - Page 19 3. Lubrication A periodic coating of lubricating oil on pivot points will help to prevent rust and assure that the pump assemblies move freely. This maintenance may be carried out by the operator 3.1. Where to lubricate for 107TA8221 Please see the picture below for the pivot points that need a periodic coating of lubrication.
-
Page 20: Troubleshooting
TROUBLESHOOTING If you need the hydraulic diagram, please contact your dealer. N° Problem Cause Action The jack won’t lift The jack is overloaded Remove excess weight a load - There is a low oil level Check the hydraulic oil level - The oil level is exceeded Air got trapped in the jack Remove air from the jack... -
Page 21: Final Decommissioning And Disposal
FINAL DECOMMISSIONING AND DISPOSAL Final, proper decommissioning or disposal of the product must be performed in accordance with the regulations of the country of application. In particular, regulations governing the disposal of batteries, fuels and electronic and electrical systems must be observed. Waste packaging should be sorted and put into solid dustbins according to the materials and needs to be collected by the local special environment protection bureau. -
Page 22: Annexes
Función / Funzione / Função Levantamiento una carga/ Sollevamento un carico Merk / Marque / Brand / Marke / Marca TotalSource Type / Typ / Tipo KRIH0001 Model/ Modèle/ Modell/ Modelo TVH/ 4618513 ● dat het zelf het TECHNISCH DOSSIER samenstelt;... - Page 23 dass Hydraulikhebber allen einschlägigen Bestimmungen der nachstehenden Richtlinien und harmonisierten Normen entspricht; que la jack cumple todas las disposiciones aplicables de las Directivas y normas armonizadas citadas abajo; che la martinetto è conforme a tutte le disposizioni pertinenti delle direttive e norme armonizzate elencate qui di seguito: que a jack cumpre todas as disposições aplicáveis das seguintes diretrizes e normas harmonizadas abaixo;...
- Page 24 EG-VERKLARING VAN OVEREENSTEMMING DÉCLARATION CE DE CONFORMITÉ EC DECLARATION OF CONFORMITY EG-KONFORMITÄTSERKLÂRUNG DECLARACIÓN CE DE CONFORMIDAD DICHIARAZIONE CE DI CONFORMITÀ DECLARAÇÃO DE CONFORMIDADE CE (Machine directive 2006/42/EC) De fabrikant, Le fabricant, The manufacturer, Der Hersteller, El fabricante, Il fabbricante, O fabricante: TVH Parts Holding NV, Brabantstraat 15, B - 8790 Waregem Verklaart met betrekking tot het hierna beschreven PRODUCT: Déclare, concernant le PRODUIT décrite ci-dessous :...
- Page 25 que le cric satisfait à l’ensemble des dispositions pertinentes des directives et normes harmonisées ci-dessous; that the machine jack fulfills all the relevant provisions of the directives and harmonized standards stated herein below; dass Hydraulikhebber allen einschlägigen Bestimmungen der nachstehenden Richtlinien und harmonisierten Normen entspricht;...
- Page 26 EG-VERKLARING VAN OVEREENSTEMMING DÉCLARATION CE DE CONFORMITÉ EC DECLARATION OF CONFORMITY EG-KONFORMITÄTSERKLÂRUNG DECLARACIÓN CE DE CONFORMIDAD DICHIARAZIONE CE DI CONFORMITÀ DECLARAÇÃO DE CONFORMIDADE CE (Machine directive 2006/42/EC) De fabrikant, Le fabricant, The manufacturer, Der Hersteller, El fabricante, Il fabbricante, O fabricante: TVH Parts Holding NV, Brabantstraat 15, B - 8790 Waregem Verklaart met betrekking tot het hierna beschreven PRODUCT: Déclare, concernant le PRODUIT décrite ci-dessous :...
- Page 27 dass Hydraulikhebber allen einschlägigen Bestimmungen der nachstehenden Richtlinien und harmonisierten Normen entspricht; que la jack cumple todas las disposiciones aplicables de las Directivas y normas armonizadas citadas abajo; che la martinetto è conforme a tutte le disposizioni pertinenti delle direttive e norme armonizzate elencate qui di seguito: que a jack cumpre todas as disposições aplicáveis das seguintes diretrizes e normas harmonizadas abaixo;...
- Page 28 Your distributer: Manufactured outside the EU for: TVH PARTS HOLDING NV Brabantstraat 15 • 8790 Waregem • Belgium T +32 56 43 42 11 • F +32 56 43 44 88 • info@tvh.com • www.tvh.com...
Need help?
Do you have a question about the KRIH0001 and is the answer not in the manual?
Questions and answers