Summary of Contents for Linde RYVAL 160 T PULSE HF
- Page 1 WELDING INVERTER RYVAL 160 T PULSE HF RYVAL 200 T PULSE HF OPERATING MANUAL Linde AG, Linde Gas Deutschland © Ryval 160-200 T PULSE HF manual EN 03...
-
Page 2: Table Of Contents
EQUIPMENT ....................7 OPERATOR CONTROLS ................8 GETTING STARTED ................. 12 TWO STROKE AND FOUR STROKE IN TIG MODE ....... 13 ROUTINE MAINTENANCE & INSPECTION ..........14 STATEMENT OF WARRANTY ..............15 DISPOSAL ....................16 Linde AG, Linde Gas Deutschland ©... -
Page 3: Introduction
3/16 INTRODUCTION Congratulations on your new Linde AG, Linde Gas Deutschland product. We are proud to have you as our customer and will strive to provide you with the best service and reliability in the industry. This Operating Manual has been designed to instruct you on the correct use and operation of your Linde AG, Linde Gas Deutschland product. -
Page 4: Safety Instructions And Warnings
The operator must be aware of all the special regulations which he needs to conform to when welding in enclosed spaces with a high risk of explosion. To prevent electric shock, we strongly suggest the following rules: Linde AG, Linde Gas Deutschland ©... -
Page 5: Open-Circuit Voltage
Before opening the machine switch off the machine and disconnect it from the power socket. Only personnel authorised by this company can carry out maintenance on the machine. NOTE: Device complies with IEC 61000-3-12. Linde AG, Linde Gas Deutschland ©... -
Page 6: Technical Data
During operation, the device may be the source of interference. We warn users Caution , that they are responsible for possible interference from welding. TECHNICAL DATA RYVAL 160 T PULSE HF Method Mains voltage V/Hz 1x230/50-60 Welding current range 5 - 160... -
Page 7: Equipment
25 A. The corresponding data for such a 32 A plug are stated in the table above in brackets. Replacement of the plug may only be performed by Linde AG, Linde Gas Deutschland as authorized service personnel. -
Page 8: Operator Controls
3176 Hose AR 1m with manom. 6053 MAGNET ON/OFF 40 kg 6052 MAGNET ON/OFF 75 kg OPERATOR CONTROLS MAIN PARTS Fig . 1 Main parts Pos. Description Operating panel LED ON Gas outlet connector Linde AG, Linde Gas Deutschland ©... - Page 9 MMA – position of the method switch 17, can be set current 25, HOT START 9 or ARC FORCE 10 by means of the encoder 21 Adjusting the gas flow - position of the method switch 17 Method switch 1. MMA coated electrode Linde AG, Linde Gas Deutschland ©...
- Page 10 LED end current - only TIG (5-160 A, 5-200 A, default 5 A) LED post gas time - only TIG (0,1-10 s, default 10 s) TIG HF 2T –TIG HF ignition, two stroke - position of the method switch 17 Linde AG, Linde Gas Deutschland ©...
- Page 11 SELECTING PULSE MODE 1. Select the required TIG method by means of method switch 17, LED 25 will illuminate 2. Press the encoder 21, then by means of turning the encoder select LED 14 Linde AG, Linde Gas Deutschland ©...
-
Page 12: Getting Started
5. Connect the torch control connector onto the matching connector 4. 6. Connect the work clamp to the work piece or at the welding table. 7. Set the method switch 17 to desired TIG method. Linde AG, Linde Gas Deutschland ©... -
Page 13: Two Stroke And Four Stroke In Tig Mode
4T HF – four stroke, HF ignition (High Frequency) 2T HF – two stroke, HF ignition (High Frequency) TWO STROKE AND FOUR STROKE IN TIG MODE TWO STROKE – 2T Welding current Down slope Current Postgas Pregas Linde AG, Linde Gas Deutschland ©... -
Page 14: Routine Maintenance & Inspection
6. Troubleshooting and repairing of Ryval welding equipment should only be carried out only by suitably qualified or competent person. 7. A ‘competent person’ must be a person who has acquired through training, Linde AG, Linde Gas Deutschland ©... -
Page 15: Statement Of Warranty
3. Linde AG, Linde Gas Deutschland will repair or replace, at its discretion, any warranted parts or components that fail due to defects in material or workmanship within the warranty period. -
Page 16: Disposal
Linde AG, Linde Gas Deutschland ©...