Cooper Security 706r - Tilt Switch/PA Transmitter Manual

Controls and Indicators

Figure 1. 706r Controls and Indicators

1. Activity LED
2. Control Button (grey)
3. PA Button (orange)
4. Lock Button (black)
5. Aerial

Introduction

The 706rEUR-00 has an integral tilt switch and can be used as a personal attack transmitter up to 900m from a Scantronic receiver.

Specifications

Part No.: 706rEUR-00

Power Supply: Lithium power cell (soldered in place)

Battery Life: Minimum 75,000 operations over a seven year period.

Temperature Range: -10 to +55°C

Dimensions: 170H x 45W x 30D (including aerial)

Weight: 68 gms

Channels 2

Display One LED for transmitter activity and learning.

Compliance Product is CE tested to EN 50081-1 and EN 50082-1.

Radio Section Operating frequency 868.6625MHz at 20kHz bandwidth. I-ETS 300 220. CE tested to I-ETS 300 339 (draft standard).

Transmitter range Up to 900m free space (range depends on the receiver aerial and the nature of the receiving path).

Compatible Equipment

762r Two channel receiver

768r/769r 8 channel receiver

790rEUR-00 Signal Strength Meter.

7500r Domestic Radio Panel

Preparing The 706r For Use

When delivered from the factory the 706r has a battery fitted and is powered up in PA mode.

Learning the Transmitter

Consult the Installation and Programming Guides for the appropriate receivers. The Activity LED pulses out the unit's ID at every activation and can be used for infra red learning.

Programming

The 706r has three modes: PA, Tilt Switch - Buzzer, and Tilt Switch - Silent. When delivered from the factory the unit is in PA mode.

Tilt Switch With Buzzer

To change from PA to Tilt Switch - Buzzer mode press and hold the Control button for five seconds. The buzzer gives a double beep and the Activity LED flashes to signal the change in mode.

Tilt Switch - Silent

To change from PA to Tilt Switch - Silent mode press and hold the Control button for seven seconds. After five seconds the 706r gives a double beep and the Activity LED flashes. After a further two seconds the 706r gives another double beep to signal the change in mode.

Note: While the 706r is in either of the Tilt Switch modes the Activity LED flashes once every 10 seconds.

To Change Back to PA Mode

To change back to PA mode press and hold the Control button again for five seconds. The buzzer gives a single beep to signal the change in mode.

Operation

Personal Attack

Press the two orange side buttons together. The transmitter does not signal if you press only one button. Note the black button fitted below the left-hand orange button. This is a safety lock to prevent false activations. Slide the black button upwards to lock the orange button.

Tilt Switch

If the 706r is in Tilt Switch - Buzzer mode then the buzzer starts a warning tone approximately 5 seconds after the unit tilts more than 45 degrees from vertical. The warning tone lasts for 15 seconds while the unit is tilted. At the end of the warning tone the unit sends an alarm signal to the receiver if it is still tilted. Restore the unit upright to silence the warning tone.

Tilt Switch - Silent mode operates in a similar way to Tilt Switch - Buzzer mode, but the unit does not give any warning tones.

Manual Over-Ride

If you wish to work for a short time with the 706r tilted past 45 degrees, then press the grey button on top of the unit to temporarily disable the tilt switch. After you press the button the unit ignores the tilt switch for 5 minutes. Press the grey button again for another delay. This facility lets you work without causing false alarms by inadvertently tilting the 706r.

Servicing

The internal lithium power cell gives at least 75,000 activations in a seven year period.

The cell is permanently soldered in place. If the battery needs changing return the whole unit to Cooper Security Ltd Service Department.

Unsoldering the battery will INVALIDATE the warranty.

Battery Care

PAY ATTENTION TO THE METHOD OF DISPOSAL. DO NOT:

DISPOSE OF THE BATTERY IN A FIRE.

ATTEMPT TO OPEN THE BATTERY.

HIT THE BATTERY WITH A HEAVY OBJECT.

SHORT CIRCUIT THE BATTERY - THERE IS A RISK OF EXPLOSION.

ATTEMPT TO RECHARGE THE BATTERY.

Contact Cooper Security Ltd. for further disposal information.

TESTING

Determine the limits of the transmitter's range and inform the user of these limits. Check that the unit will function in all areas where the user EXPECTS it to function and point out any discrepancies.

To ensure good reception use the Scantronic 790 field strength meter to obtain accurate field strength readings and audible and visual indication of the transmitter's performance and any interference present.

Transmitter range depends on the receiver aerial and the nature of the receiving path.

To reduce the problems, there are a number of simple guidelines that can be followed:

NEVER use the transmitter on a metal surface, including foil-backed wallpaper.