Table of Contents
Advertisement
Quick Links
Table of Contents
1. Introduction ............................................................................................................................................... H1
2. Warranty and liability ................................................................................................................................. H2
2.1 Warranty ......................................................................................................................................................... H2
2.2 Liability ............................................................................................................................................................ H2
3. Safety and the environment ....................................................................................................................... H3
3.1 General safety ................................................................................................................................................. H3
3.2 Environment .................................................................................................................................................... H3
3.3 Warning labels and pictograms ....................................................................................................................... H4
4. Inspection before and during use ............................................................................................................... H5
4.1 Checks to be performed before use ................................................................................................................ H5
4.2 Shortening the PTO shaft ................................................................................................................................ H5
4.3 Connecting the SAMON Haulm Topper .......................................................................................................... H6
4.4 Inspection after ± 5 metres ............................................................................................................................. H6
4.5 Inspection and maintenance after ± 5 ha. ...................................................................................................... H6
5. Maintenance .............................................................................................................................................. H7
5.1 Lubrication schedule ....................................................................................................................................... H7
5.2 Adjusting drive belts........................................................................................................................................ H8
5.3 Gear drive maintenance .................................................................................................................................. H9
5.3.1 Topping up the gear drive oil ....................................................................................................................... H9
5.3.2 Replacing the gear drive oil .......................................................................................................................... H9
5.4 Aligning wheels with automatic depth control ............................................................................................ H10
5.5 Automatic depth control .............................................................................................................................. H11
5.5.1 Adjusting automatic depth control folding height ..................................................................................... H11
5.5.2 Adjusting width of automatic depth control probes .................................................................................. H11
5.5.3 Adjusting and setting automatic depth control valve block ...................................................................... H12
5.5.4 Adjusting automatic depth control sensors after repair/installation ........................................................ H13
6. Transport and storage .............................................................................................................................. H14
6.1 Transport by transport vehicles .................................................................................................................... H14
6.2 Transport by tractor ...................................................................................................................................... H14
6.3 Storage .......................................................................................................................................................... H15
7. Technical data .......................................................................................................................................... H16
8. Technical diagrams ................................................................................................................................... H17
8.1 Hydraulic diagram of automatic depth control ............................................................................................. H17
8.2 Hydraulic diagram of folding frame ............................................................................................................. H18
8.3 Electrical diagram (only for automatic depth control) .................................................................................. H19
9. Ordering parts .......................................................................................................................................... H20
10. Faults ...................................................................................................................................................... H21
11. EC Declaration of Conformity ................................................................................................................. H22
Advertisement
Table of Contents
Related Manuals for Samon SU15AO3B
Summary of Contents for Samon SU15AO3B
-
Page 1: Table Of Contents
4.1 Checks to be performed before use ........................ H5 4.2 Shortening the PTO shaft ..........................H5 4.3 Connecting the SAMON Haulm Topper ......................H6 4.4 Inspection after ± 5 metres ..........................H6 4.5 Inspection and maintenance after ± 5 ha....................... H6 5. -
Page 2: Introduction
Introduction. This edition of the manual is intended for buyers of a SAMON Haulm Topper. It contains information for the use and maintenance of this machine. When this manual was compiled the utmost care was taken to ensure that the illustrations and technical data are correct and current for this manual. -
Page 3: Warranty And Liability
SAMON Haulm Topper for purposes it is not intended for is considered improper use. * For harvesting any other types of deciduous species and crops, always first check with your Samon dealer. This warranty is provided on construction defects in the machine encountered during normal use. -
Page 4: Safety And The Environment
• The SAMON Haulm Topper is fitted with a ball valve on the hydraulic hose. This valve must be closed when the Haulm Topper is folded away in order to prevent the Haulm Topper from folding out. -
Page 5: Warning Labels And Pictograms
13.3 x 6.4 TL6310 “Max 30 l/min” label 6.0 x 5.0 TL6320 “Blade speed” label 9.8 x 7.8 TL6312 If any of these labels should be missing or illegible you can order a replacement at your SAMON dealer. www.samon.nl - info@samon.nl V1-2023-EN... -
Page 6: Inspection Before And During Use
Inspections before and during use WARNING!!! When performing maintenance on the SAMON Haulm Topper always switch the tractor engine off and remove the key from the ignition. After switching off the machine, wait until the blades come to a complete halt! Checks to be performed before use •... -
Page 7: Connecting The Samon Haulm Topper
Install the supplied hydraulic hoses; the thicker hydraulic hose is the return hose. NOTE!!! Use with a SAMON Haulm Topper with automatic depth control of up to 30 L/min and always connect the return hose to a pressure-free return! •... -
Page 8: Maintenance
Maintenance WARNING!!! When performing maintenance on the SAMON Haulm Topper always switch the tractor engine off and remove the key from the ignition. After switching off the machine, wait until the blades come to a complete halt! Lubrication schedule Lubricate periodically to ensure that the SAMON Haulm Topper works optimally. -
Page 9: Adjusting Drive Belts
Adjusting drive belts Each part of the SAMON Onion Haulm Topper, left, right and the centre, has a structure for adjusting the drive belts. The following applies to each part: • Make sure that the SAMON Onion Haulm Topper is folded out and standing on a flat, level surface. -
Page 10: Gear Drive Maintenance
NOTE!!! The gear drive oil must be replaced every 2 years. 5.3.1 Topping up the gear drive oil • Make sure the SAMON Onion Haulm Topper is standing on a flat, level surface. • Remove the PTO shaft(s). • Remove bleed nipple or vent hose (A) at the top. -
Page 11: Aligning Wheels With Automatic Depth Control
Turn the wheel sets in the maximum extended position and remove the connection hoses. • Screw the protective caps of the connecting nipples back on. • Check the alignment again. • Red connection: Long hose • Green connection: Short hose www.samon.nl - info@samon.nl V1-2023-EN... -
Page 12: Automatic Depth Control
Automatic depth control If the SAMON Haulm Topper is equipped with an automatic depth control, it will be necessary to adjust the cutting height and working width of the probes. Cutting height ➔ 5.5.1 adjustment: ➔ Width adjustment: 5.5.2 5.5.1 Adjusting automatic depth control folding height •... -
Page 13: Adjusting And Setting Automatic Depth Control Valve Block
The valve block has been set to the proper pressure and flow at the factory. WARNING!!! When performing maintenance on the hydraulic system of the SAMON Haulm Topper, make sure that there is no pressure on the system. Always remove the hydraulic hoses before maintenance. -
Page 14: Adjusting Automatic Depth Control Sensors After Repair/Installation
The sensors and plugs of the magnet coils are provided with a LED to facilitate in controlling their operation. When in operation, the LED will light up. NOTE!!! The minimum distance between sensor and reaction plate is 1.5 mm in order to ensure maximum performance by the automatic depth control. www.samon.nl - info@samon.nl V1-2023-EN... -
Page 15: Transport And Storage
• The blades are unprotected when the SAMON Haulm Topper is folded and lifted. • Also keep in mind that the sight of the driver is limited when the SAMON Haulm Topper is connected to a tractor. www.samon.nl - info@samon.nl... -
Page 16: Storage
• Check all bearings and replace when clearance is excessive. NOTE!!! Replacement of the lower bearings of the topper shafts must be carried out by an authorised SAMON dealer. The bearings require precise adjustment to minimise wear. • Check the bolts on the blades and the blades for wear and replace in time. -
Page 17: Technical Data
Technical data SAMON 3-Bed Haulm Topper “Open model” 1.5 metres 1.8 metres 2.0 metres Working width: Rear Rear Rear Use: SU15AO3B SU18AO3B SU20AO3B Type: 1000 PTO 1000 PTO 800-900 PTO PTO shaft: SAE.90EP SAE.90EP SAE.90EP Gear drive oil: 260x250x290 cm... -
Page 18: Technical Diagrams
Technical diagrams Hydraulic diagram of automatic depth control www.samon.nl - info@samon.nl V1-2023-EN... -
Page 19: Hydraulic Diagram Of Folding Frame
Hydraulic diagram of folding frame www.samon.nl - info@samon.nl V1-2023-EN... -
Page 20: Electrical Diagram (Only For Automatic Depth Control)
Electrical diagram www.samon.nl - info@samon.nl V1-2023-EN... -
Page 21: Ordering Parts
Ordering parts Follow the instructions below for ordering parts to ensure quick and correct delivery. 1. Only order parts from official SAMON dealers. 2. Include the type, model and serial number of your machine as stated on the type shield. -
Page 22: Faults
Check by measuring and replace if necessary. Depth control works slowly Insufficient pressure Perform pressure measurement and change with the pressure control valve, if necessary (Up to 120 Bar) Insufficient flow Reset 3-way control valve (See 5.6.3) www.samon.nl - info@samon.nl V1-2023-EN... -
Page 23: Ec Declaration Of Conformity
Company Ellens Landbouwtechniek BV Name Mr M. Ellens Country the Netherlands Done at Nagele, 4 October 2022 Company Ellens Landbouwtechniek BV Name Mr O. Ellens Signature www.samon.nl - info@samon.nl V1-2023-EN...
Need help?
Do you have a question about the SU15AO3B and is the answer not in the manual?
Questions and answers