(REF_65W_2C_GAN_PAG1). Intended audience This document is primarily intended for EZ-PD™ PAG1S-1P multiport charger and adapter solution developers. User guide Please read the sections “Important notice” and “Warnings” at the end of this document 002-37406 Rev. *A www.infineon.com 2023-04-21...
EZ-PD™ PAG1S-1P based 65 W ATQ GAN USB PD dual-C charger and adapter solution user guide Table of contents Table of contents About this document ........................1 Table of contents ..........................2 Introduction .......................... 3 Specification ......................... 5 Board overview ........................6 Procedure to program EZ-PD™...
Figure 1 High-level block diagram of a dual-port adapter Infineon provides a comprehensive solution for both sections of adapters, i.e., AC-DC and buck converters. Specifically, for AC-DC conversion, Infineon’s EZ-PD™ PAG1x-based solution, along with the EZ-PD™ CCG7DC- based buck converter, ensure compatibility with USB PD/Programmable Power Supply (PPS) standards. The EZ-PD™...
Page 4
Table 1 Critical components bill of materials (BOM) Designator Description Part number Manufacturer EZ-PD™ PAG1S USB PD power adapter CYPAS111A1-24LQXQ Infineon Technologies secondary side controller EZ-PD™ PAG1P primary side startup CYPAP112A3-10SXQ Infineon Technologies controller EZ-PD™ CCG7DC dual-port USB Type-C CYPD7271-68LQXQES...
EZ-PD™ PAG1S-1P based 65 W ATQ GAN USB PD dual-C charger and adapter solution user guide Specification Specification Table 2 Test specifications Parameter Value Input voltage and frequency 90 to 264 V AC, 47 to 63 Hz Max output power 65 W system power with dual-C and a max load current of 3.25 A 65 W on each port with a max load current of 3.25 A Output voltage...
EZ-PD™ PAG1S-1P based 65 W ATQ GAN USB PD dual-C charger and adapter solution user guide Board overview Board overview The EZ-PD™ PAG1S-1P based 65 W USB PD dual-C charger and adapter solution (REF_65W_2C_GAN_PAG1 + CCG7DC 65W_2C with ATQ) shown in Figure 2 solution board is designed to meet the specifications shown in Table...
EZ-PD™ PAG1S-1P based 65 W ATQ GAN USB PD dual-C charger and adapter solution user guide Procedure to program EZ-PD™ CCG7DC-based daughter board Procedure to program EZ-PD™ CCG7DC-based daughter board EZ-PD™ PAG1S and EZ-PD™ CCG7DC support PSoC™ MiniProg4 (CY8CKIT-005) as a programmer to program the EZ-PD™...
EZ-PD™ PAG1S-1P based 65 W ATQ GAN USB PD dual-C charger and adapter solution user guide Test setup Test setup Figure 6 shows the test setup to capture the electrical data of the DUT. The following setup is the optimal one to capture efficiency by capturing: Input power using a power meter ...
EZ-PD™ PAG1S-1P based 65 W ATQ GAN USB PD dual-C charger and adapter solution user guide Test setup Power adapter tester (PAT) Connect the DUT to a USB-C power adapter tester (PAT) using a USB Type-C cable. After the connection is established, the PAT UI does a PDO discovery and displays the results.
EZ-PD™ PAG1S-1P based 65 W ATQ GAN USB PD dual-C charger and adapter solution user guide Quick steps for demo Quick steps for demo Connect the 65 W solution board to the power meter AC terminal (which is already connected to the programmable AC supply) as in Figure Connect a USB PD tester or a power adapter tester (PAT) to the port and ensure that the USB PD tester gets...
EZ-PD™ PAG1S-1P based 65 W ATQ GAN USB PD dual-C charger and adapter solution user guide References References Datasheets EZ-PD™ PAG1P, Primary side startup controller EZ-PD™ PAG1S - CYPAS111, USB PD power adapter secondary side controller CYPD7271, EZ-PD™ CCG7DC dual-port USB-C Power Delivery and DC-DC controller User guide 002-37406 Rev.
EZ-PD™ PAG1S-1P based 65 W ATQ GAN USB PD dual-C charger and adapter solution user guide Revision history Revision history Document Date Description of changes revision 2023-04-04 Initial release 2023-04-21 Post to web User guide 002-37406 Rev. *A 2023-04-21...