Related Manuals for GREISINGER GIR 230 Pt
Summary of Contents for GREISINGER GIR 230 Pt
- Page 1 E33.0.11.6C-03 Manual for connection and operation of the GIR 230 Pt Page 1 of 14 Manual for connection and operation of GIR 230 Pt Version 1.1...
-
Page 2: Table Of Contents
E33.0.11.6C-03 Manual for connection and operation of the GIR 230 Pt Page 2 of 14 Index 1. SAFETY REGULATIONS ............................3 2. INTRODUCTION ................................ 4 3. ELECTRICAL CONNECTION..........................4 3.1. Terminal assignment..............................4 3.2. Connection data ............................... 4 3.3. Connecting an input signal............................5 3.3.1. -
Page 3: Safety Regulations
E33.0.11.6C-03 Manual for connection and operation of the GIR 230 Pt Page 3 of 14 1. Safety regulations This device was designed and tested considering the safety regulations for electronic measuring devices. Faultless operation and reliability in operation of the measuring device can only be assured if the General Safety Measures and the devices specific safety regulations mentioned in this users manual are considered. -
Page 4: Introduction
Manual for connection and operation of the GIR 230 Pt Page 4 of 14 2. Introduction The GIR 230 Pt is a microprocessor controlled displaying, monitoring and controlling device. The device is supporting one interface for the connection of: - Pt100 (3-wire-technology),... -
Page 5: Connecting An Input Signal
E33.0.11.6C-03 Manual for connection and operation of the GIR 230 Pt Page 5 of 14 3.3. Connecting an input signal Please take care not to exceed the limitations of the inputs when connecting the device as this may lead to destruction of the device.. -
Page 6: Configuration Of The Device
E33.0.11.6C-03 Manual for connection and operation of the GIR 230 Pt Page 6 of 14 4. Configuration of the device Please note: When you are configuring the device and don’t press any button for more than 60 sec. the configuration of the device will be cancelled. The changes you made will not be saved and will be lost! Hint: The buttons 2 and 3 are featured with a ‘roll-function‘. -
Page 7: Selection Of The Output Function
E33.0.11.6C-03 Manual for connection and operation of the GIR 230 Pt Page 7 of 14 4.2. Selection of the output function The Display now shows “outP“. (output) Use button 2 and button 3 (middle and right button) to select the desired output-function. -
Page 8: Switchpoints And Alarm-Boundaries
E33.0.11.6C-03 Manual for connection and operation of the GIR 230 Pt Page 8 of 14 5. Switchpoints and alarm-boundaries Please note: The settings of the switchpoints will be cancelled, when no button was pressed for more than 60 sec. changes you may have made already won‘t be saved and will be lost! Hint: The buttons 2 and 3 are featured with a ‘roll-function‘. -
Page 9: 2-Point-Controller With Alarm Function, 3-Point-Controller With Alarm Function
E33.0.11.6C-03 Manual for connection and operation of the GIR 230 Pt Page 9 of 14 Now you finished configuring the switching points of your device. Press button 1 to switch over to display the measuring value. 5.2. 2-point-controller with alarm function, 3-point-controller with alarm function This chapter describes how to configure the device as a 2-point-controller with alarm function or 3-point- controller with alarm function. -
Page 10: Minimum/Maximum-Alarm
E33.0.11.6C-03 Manual for connection and operation of the GIR 230 Pt Page 10 of 14 5.3. Minimum/maximum-alarm This chapter describes how to configure the device‘s alarm boundaries for min-/max-alarm-monitoring. This instruction demands that you selected “AL“ as your desired output function. -
Page 11: Offset- And Slope-Adjustment
E33.0.11.6C-03 Manual for connection and operation of the GIR 230 Pt Page 11 of 14 8. Offset- and slope-adjustment The offset and slope-adjustment function can be used for compensating the tolerance of the used probes. Please note: The settings of the offset- / slope-adjustment will be cancelled, when no button was pressed for more than 60 sec. -
Page 12: Error Codes
E33.0.11.6C-03 Manual for connection and operation of the GIR 230 Pt Page 12 of 14 9. Error codes When detecting an operating state which is not permissible, the device will display an error code The following error codes are defined: Err.1:... -
Page 13: Specification
E33.0.11.6C-03 Manual for connection and operation of the GIR 230 Pt Page 13 of 14 10. Specification Absolute maximum ratings: Performance data Limit values Connection Notes between min. max. min. max. 207 V 244 V 253 V Supply voltage 3 and 4... - Page 14 E33.0.11.6C-03 Manual for connection and operation of the GIR 230 Pt Page 14 of 14...
Need help?
Do you have a question about the GIR 230 Pt and is the answer not in the manual?
Questions and answers