Page 1
IM3080 11/2022 REV05 CITOMIG 185MP & 210MP OPERATOR’S MANUAL ENGLISH Lincoln Electric Bester Sp. z o.o. ul. Jana III Sobieskiego 19A, 58-260 Bielawa, Poland...
12/05 THANKS! For having chosen the QUALITY of Lincoln Electric products. Please Examine Package and Equipment for Damage. Claims for material damaged in shipment must be notified immediately to the dealer. For future reference record in the table below your equipment identification information. Model Name, Code & Serial Number can be found on the machine rating plate.
Efficiency and idle power consumption: Efficiency when max power consumption Index Name Equivalent model / Idle power consumption W000403579 CITOMIG 185MP 81,6% / 42W No equivalent model W000403578 CITOMIG 210MP 80,7% / 47W No equivalent model Idle state occurs under the condition specified in below table...
Page 6
Typical gas usage for MIG/MAG equipment: DC electrode positive Wire Wire Feeding Gas flow Material type diameter Shielding Gas Current Voltage [m/min] [l/min] [mm] Carbon, low 0,9 ÷ 1,1 95 ÷ 200 18 ÷ 22 3,5 – 6,5 Ar 75%, CO alloy steel Aluminium 0,8 ÷...
Electromagnetic Compatibility (EMC) 11/04 This machine has been designed in accordance with all relevant directives and standards. However, it may still generate electromagnetic disturbances that can affect other systems like telecommunications (telephone, radio, and television) or other safety systems. These disturbances can cause safety problems in the affected systems. Read and understand this section to eliminate or reduce the amount of electromagnetic disturbance generated by this machine.
Safety 11/04 WARNING This equipment must be used by qualified personnel. Be sure that all installation, operation, maintenance and repair procedures are performed only by qualified person. Read and understand this manual before operating this equipment. Failure to follow the instructions in this manual could cause serious personal injury, loss of life, or damage to this equipment. Read and understand the following explanations of the warning symbols.
Page 9
WELDING SPARKS CAN CAUSE FIRE OR EXPLOSION: Remove fire hazards from the welding area and have a fire extinguisher readily available. Welding sparks and hot materials from the welding process can easily go through small cracks and openings to adjacent areas. Do not weld on any tanks, drums, containers, or material until the proper steps have been taken to insure that no flammable or toxic vapors will be present.
Introduction The welding machines CITOMIG 185MP enables welding: following equipment been added CITOMIG 185MP and CITOMIG 210MP: GMAW (MIG/MAG). Work lead – 3m. FCAW-SS. Gas hose – 2m. SMAW (MMA). Driving roll V0.8/V1.0 for solid wire (mounted in the The welding machines CITOMIG 210MP enables welding: wire feeder).
Page 11
If the Controls and Operational Features value is higher, the arc will be 1. LED Indicator Power switch (only CITOMIG 185MP): softer and during welding is This LED lights up when the welding machine is ON less spatters.
Page 12
15. Escape Button (right): 18. Power Lead with Plug (2m): Power lead with plug is a standard equipment. Connect the power lead with plug Cancels an action / exit menu. to the main supply before turning power on. Locks and unlocks knobs and buttons on the panel (press and hold button for 4 seconds).
Page 14
Loading the Electrode Wire Adjusting of Force of Pressure Roll Force Turn the machine off. Open the side cover of the machine. The pressure arm controls the amount of force the drive Unscrew the locking nut of the sleeve. rolls exert on the wire.
Page 15
Welding GMAW, FCAW-SS Process 2-Step / 4-Step Burnback CITOMIG 185MP and CITOMIG 210MP can be used to Run-in WFS welding GMAW and FCAW-SS process. Spot Time CITOMIG 210MP has been provided with synergic ...
Page 16
Welding SMAW (MMA) Process The welding load voltage can be changed depend on the value of parameters are set by operators: CITOMIG 185MP and CITOMIG 210MP does not include CITOMIG 210MP the electrode holder with lead necessary for SMAW welding, but the one can be purchased separately.
Page 17
Depending on welding machine, the user can set Contact with the Technical Service Center or Lincoln functions: Electric, when a machine’s display of CITOMIG 210MP CITOMIG 185MP will show a message of the Figure 7 or similar. The welding current ...
Page 18
Guide’s Marking Interface CITOMIG 210MP Description of the user interface in "Quick Guide" chapter. Select Welding Process SMAW (MMA) Welding Basic menu GMAW (MIG/MAG) Burnback Brightness Level Manual Welding View Software FCAW- Self shielded Run-in WFS Hardware Version Manual Welding Information GMAW (MIG/MAG)
Page 19
Please refer Keep the machine clean. Using a dry (and low www.oerlikon-welding.com for any updated information. pressure) airflow, remove the dust from the external case and from the cabinet inside.
WEEE 07/06 Do not dispose of electrical equipment together with normal waste! In observance of European Directive 2012/19/EC on Waste Electrical and Electronic Equipment (WEEE) and its implementation in accordance with national law, electrical equipment that has reached the end of its life must be collected separately and returned to an environmentally compatible recycling facility.
Accessories W10429-15-3M The gas-cooled gun LGS2 150 G-3.0M to GMAW process - 3m W10429-24-3M The gas-cooled gun LGS2 240 G-3.0M to GMAW process - 3m W10429-25-3M The gas-cooled gun LGS2 250 G-3.0M to GMAW process - 3m W10529-17-4V WTT2 17V 4M 1/4G 35-50 E/H-200A-25-3M Welding cable with electrode holder to SMAW process - 3m.
Need help?
Do you have a question about the CITOMIG 185MP and is the answer not in the manual?
Questions and answers