Preparation; Unpacking The Tv - JVC LT-55K870 Instruction Manual

55" led smart 4k ultra hd tv

page of 112

/ 112
Contents
Table of Contents
Bookmarks

Table of Contents

Available languages

Chapter

Preparation

Thank you

Your new TV has many features and incorporates the latest technology to enhance your viewing

experience. We recommend that you spend some time reading this instruction manual so that you fully

understand these features. You will also find some hints and tips to help you resolve any issues.

Read all the safety instructions carefully before use and keep this instruction manual for future reference.

Unpacking the TV

Remove all packaging from the TV. Retain the packaging. If you dispose of it please do so according to local regulations.

The following items are included:

TV Stand Neck Cover and

Neck

Instruction Manual

Εγχειρίδιο χρήσης

55" LED Smart 4K Ultra HD TV

LED Smart 4K Ultra HD TV 55 ιντσών

LT-55K870

Instruction Manual

JVC 55' LED Smart 4K Ultra HD TV LT-55K870 Manual GR.indd 13

for purchasing your new JVC TV.

Screws x5

TV Stand Base

Quick Start Guide

55" LED Smart 4K Ultra HD TV

LT-55K870

Thank you

for purchasing your new JVC TV.

Your new TV incorporates the latest technology to enhance your viewing

experience. We would suggest that you allow about 20 mins for initial setup.

Please follow this guide for a successful first time installation.

The latest eco-friendly power-saving technology will switch off the TV if

it is left on and idle for 4 hours. Please refer to "Auto Standby" under the

"Time Settings" section of the instruction manual for more detail.

Unpacking

Remove all packaging from the unit. Retain the packaging. If you dispose of it please do so according to any local regulations.

TV Stand Base

Screws (B) x 6

TV Stand Neck

Remote Control/

Instruction Manual

AAA Batteries x2

TV Stand Neck cover

Quick Start Guide

Screws (A) x 5

Please inspect your TV for damage after unpacking. If you do notice any damage please consult your dealer.

Operating Your Remote Control

1. Slide open the battery compartment on the back of the remote control.

2. Insert two AAA size batteries. Make sure to match the (+) and ( - )

ends of the batteries with the (+) and ( - ) ends indicated in the battery

compartment.

3. Slide the battery compartment cover back into place. Make sure it clicks

into place.

JVC 55' LED Smart 4K Ultra HD TV LT-55K870 Quick Start.indd 1

Quick Start Guide

Screws x6

Installing the Base Stand

Fitting the Neck and Neck

Cover Together

Cushioned

1. Fit the neck cover over the neck.

material

2. Using 2 of the supplied screws (A),

Protective

screw the neck and neck cover

Table

Bag

together.

Fitting the Neck and Stand to the TV

3. Ensure the TV is switched off and not connected to

the mains power supply.

4. Lay the TV down on a flat surface ideally on the

edge of a table so the base of the TV slightly

overhangs the edge of the table, with the back side

facing up. Please make sure a soft cushioned

material (such as a dry bath towel or thick piece of

foam) is placed beneath the screen. You can leave

the protective bag on to protect the TV at this point.

5. Slide the Neck and Neck cover under the lip, the

neck will fit snugly over the screw holes. Then screw

the Neck to the TV using the 6 screws (B) supplied.

6. Once the Neck is secure screw the base to the neck

using the 3 screws (A) supplied. Be careful not the

drop the base, its heavy.

The LCD display is very fragile, and must be protected at all times when installing and removing the base stand. Be sure that no hard or sharp object,

or anything that could scratch or damage the LCD display, comes into contact with it. DO NOT exert pressure on the front of the TV at any time because

the screen could crack.

Connecting the Aerial and Turning on the TV

1. Connect one end of the RF coaxial cable

Optional

to the aerial socket on the wall and the

other end of the cable to the ANT socket

If you want to connect to the internet via a wired connection then

on the back of your TV.

connect your ethernet cable to the LAN socket.

2. Plug the TV into a mains socket and

switch on at the mains.

3. In standby mode, press the