Subscribe to Our Youtube Channel
Related Manuals for jcb 21-AG125
Summary of Contents for jcb 21-AG125
- Page 1 POWER TOOL INSTRUCTION & USER MANUAL 21-AG125 Original Instructions IM-AG125-EN Iss: 06/2021...
- Page 2 The month and year of manufacture can be found within the product serial number e.g. MMYYPPPAXXXXX. Where production month (MM) and production year (YY) are included. 21-AG125 Designation of the tool (AG - Angle Grinder), 125 (125mm disc diameter). 21-AG125...
-
Page 3: Table Of Contents
Power Switch Constant Speed Grinding Surface Grinding Edge Grinding (Cutting) Surface Finishing with Sanding Flap Discs Maintenance Transport and Storage Storage and Handling of Recommended Accessories WARRANTY STATEMENT Terms & Conditions EU/UK DECLARATION OF CONFORMITY 21-AG125 Instruction & User Manual... -
Page 4: Work Area Safety
Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. 21-AG125 Instruction & User Manual... -
Page 5: General Power Tool Safety Warnings
Such preventive safety measures reduce the risk of starting the power tool accidentally. 21-AG125 Instruction & User Manual... -
Page 6: Tool Specific Safety Warnings
Operations for which the power tool was power tool will run out of balance, vibrate not designed may create a hazard and cause excessively and may cause loss of control. personal injury. 21-AG125 Instruction & User Manual... -
Page 7: Wire Brushing, Polishing Or Abrasive Cutting-Off Operations
Do not operate the power tool near area of operation. flammable materials. Sparks could ignite these materials. 21-AG125 Instruction & User Manual... -
Page 8: Kickback And Related Warnings
The guard helps to protect the Never place your hand near the operator from the broken wheel fragments, rotating accessory. Accessory may accidental contact with wheel and sparks kickback over your hand. that could ignite clothing. 21-AG125 Instruction & User Manual... -
Page 9: Additional Safety Warnings Specific For Abrasive
21-AG125 Instruction & User Manual... -
Page 10: Safety Warnings Specific For Sanding Operations
Tuck away or supply cord is damaged, it must be replaced trim any loose attachment strings. by the manufacturer or an authorised JCB Loose and spinning attachment strings Service Centre in order to avoid a hazard. -
Page 11: Component List
COMPONENT LIST ON/ OFF SWITCH SIDE HANDLE SPINDLE LOCK GUARD LOCKING NUT GRINDING DISC LOWER PLATE PIN WRENCH 21-AG125 Instruction & User Manual... -
Page 12: Technical Data
(taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time). 21-AG125 Instruction & User Manual... -
Page 13: Vibration Information
Plan your work schedule to spread any high vibration tool use across a number of days. THIS TOOL MAY CAUSE HAND-ARM VIBRATION SYNDROME IF USAGE IS NOT ADEQUATELY MANAGED. 21-AG125 Instruction & User Manual... -
Page 14: Operating Instructions
Screw the locking nut (raised boss innermost) onto the output shaft, on top of Switch off the tool and disconnect the power the grinding wheel. (remove battery/unplug) before changing Press down the spindle lock button. grinding discs. 21-AG125 Instruction & User Manual... -
Page 15: Power Switch
The power tool will come to a stop. Grinding Allow the tool to reach full speed before touching the tool to the work surface. 21-AG125 Instruction & User Manual... -
Page 16: Surface Finishing With Sanding Flap Discs
(remove the battery/ corrosive, abrasive additives. This risks unplug the power cord) before transport. damaging the surfaces of the tool. Always carry the tool using the purpose- designed handle. 21-AG125 Instruction & User Manual... -
Page 17: Storage And Handling Of Recommended Accessories
Tools shall also be marked with an indication of direction of rotation of the spindle. This shall be indicated by an arrow, raised or sunk, or by any other means on less visible and indelible. 21-AG125 Instruction & User Manual... -
Page 18: Warranty Statement
Warranty cover commences from the date of purchase on the retail sales receipt and is valid only for JCB Tools products purchased within the UK bearing the CE and UKCA mark and a visible serial number. - Page 19 Repairs have not been undertaken using non-genuine spare parts. JCB Power Tools used for Hire Fleets or as part of B2B and Service Contracts are not covered by these terms and conditions. JCB Tools 3 Year Warranty excludes the following (where applicable): Components normally subject to wear such as carbon brushes.
-
Page 20: Eu/Uk Declaration Of Conformity
JCB-AG125-M, 21-AG125-M DECLARATION: EU Product Code No. JCB-AG125-M-E Factory Reference No. ML-53118B Name: Yellow and Black Tools Ltd. (T/A: JCB Tools) IDENTIFICATION DETAILS OF Unit 55 Romsey Industrial Estate, Greatbridge Road Address: MANUFACTURER: Romsey, Hampshire SO51 0HR Country: Authorised Representative Service...
Need help?
Do you have a question about the 21-AG125 and is the answer not in the manual?
Questions and answers