Do you have a question about the 2515R and is the answer not in the manual?
Questions and answers
Dan Chick
May 16, 2025
I want to remove WIFO pull behind snowblower from TYM 2515R. Having a lot of trouble. Pins are real tight so can't even get started.
1 comments:
Mr. Anderson
May 22, 2025
To remove the WIFO pull-behind snowblower from a TYM 2515R when the pins are tight, move the draw bar forward and backward to help align and release the lock pin. This may reduce tension and allow the pin to be removed more easily.
This answer is automatically generated
Scott Campbell
June 26, 2025
Where do I find the drain plug for my radiator on the TYM 2515?
Page 1
PREFACE This operator’s manual contains handling tips and precautions for safe operation of your TYM.2515R(H)./. 3015R(H)./.3515R(H)./.4215R(H)./.4815R(H).tractor. Read it carefully before you operate your tractor and make sure that you have a full understanding of this manual. This will ensure correct operation and to keep the tractor optimum condition.
TABLE OF CONTENTS FOR SAFE OPERATION .......... REGARDING WARRANTY SUPPORT ....... SECTION SPECIFICATION ............ DESCRIPTION OF OPERATING SYSTEM ...... CONTROLS AND COMPONENTS ........ PERIODIC CHECKS AND MAINTENANCE ...... DIAGNOSIS AND TROUBLE SHOOTINGS .........
Page 4
SAFETY AND VEHICLE DAMAGE WARNING This manual includes information titled as DANGER, WARNING, CAUTION, IMPORTANT. These safety marks stand for the safety precaution so follow the instruction with special attention: This symbol indicates that a condition may result in harm, fatal injury or death to you or oth- er persons if this instruction is ignored.
Page 5
SYMBOL MARKS OF CONTROLLER This manual includes symbol marks of the controller to simplify operations for maneuverability and main- tenance. These meanings are as below, so carefully read it for a proper function. Left side indicator Right side indicator Preheat Engine oil pressure Battery Parking Brake...
Page 6
"USE AND DISPOSAL" POLICY CONCERNED WITH ENVIRONMENT PRESERVATION We try our best to preserve the environment, and are always concerned about our environmental impact at each step of planning, development, production, distribution, use and disposal of products, and for our overall operations through an “environmentally friendly” management system. We comply with inter- national environmental regulations, environmental regulations designated by country and local authori- ties and other requirements with which we are in agreement, and we work towards the prevention of envi- ronmental pollution and the conservation of resources.
1. FOR SAFE OPERATION SAFETY PRECAUTIONS..............1-2 BEFORE USING THE MACHINE ..................1-2 BEFORE WORKING ......................1-11 WHILE WORKING......................1-16 AFTER USING THE MACHINE ..................1-17 PRECAUTION FOR PROLONGED STORAGE ..............1-21 OTHER .........................1-23 DECAL MOUNTING LOCATION............. 1-31 DECAL..................1-33 CAUTIONS FOR DECAL MAINTENANCE ..............1-36...
TYM TRACTOR SAFETY PRECAUTIONS BEFORE USING THE MACHINE If the instructions in this chapter are ignored, it may cause a machine fail- ure, a fatal accident with injury or death. Ventilating For further detailed information, refer 환기를 충분히 to each chapter.
Page 9
OR YO R A WARNING 6015O103A 6015O104A WARNING WARNING ...
Page 19
OR YO R A Use a cor- Do not inflate rect tool 공구는 the tire bead 올바르게! 최대 공기압 이상 max air pres- 으로 공기를 넣지 sure 마십시오. 6640O132A 6015O131A 6640O133A WARNING CAUTION CAUTION ...
OR YO R A PRECAUTION FOR PROLONGED STORAGE It's HOT! 앗 뜨거! 닿 으 면 안 돼 공 구 함 6640O155A 6015O156A 6015O157A CAUTION CAUTION CAUTION ...
Page 28
TYM TRACTOR 는 와 Be Careful Remove from 어느쪽도 connect + first tractor 떼어내서 보관하세요. connect + later 좋아! 취부는 + when connecting 떼어낼떼는 -부터! 6640O158A 6640O159A 6015O160A CAUTION WARNING WARNING ...
OR YO R A DECAL (1) No.: TA00036924A (2) No.: TZE5130000C4 (3) No.: TZE5180000C4 WARNING SURFACE (4) No.: TA00040603A [MEC. Model] TZE5130000C4 Clutch pedal Locker Stopper For the long storage, please lock clutch pedal in the both Traction and PTO clutch are disengaged position TA00040603A...
Page 40
TYM TRACTOR (5) No.: TZE4190000C4 (6) No.: TZE5110000B4 (7) No.: TZE5160000B3 DANGER TO AVOID PERSONAL INJURY: 1. Read and understand the operator’s manual before operation Start only from 2. Before starting the engine, make sure that everyone is at a safe distance from the...
Page 41
OR YO R A (11) No.: TA00015596B (12) No.: TZE4100000B4 [MEC. Model] (13) No.: TZE5770000B3 WARNING WARNING TO AVOID PERSONAL INJURY: 1. Keep PTO shield in place at all times. TO AVOID PERSONAL INJURY(OPERATING ON SLOPES) 2. Do not operate the PTO at speeds faster CONNECT THE LEFT 1.
TYM TRACTOR CAUTIONS FOR DECAL MAINTENANCE Safety decals are attached to the trac- IMPORTANT tor for safe operation. Make sure to fol- low the instruction on the decals as well as the following instruction: CAUTION ...
2. REGARDING WARRANTY SUPPORT REGARDING WARRANTY CERTIFICATE........... 2-2 REGARDING AFTER-SALES SERVICE..........2-2 VEHICLE IDENTIFICATION NUMBER (VIN)..............2-2 REGARDING SUPPLYING SERVICE PARTS........2-3 REGARDING GENUINE PARTS AND FLUID..........2-3...
Page 44
TYM TRACTOR REGARDING WARRANTY REGARDING AFTER-SALES SERVICE CERTIFICATE VEHICLE IDENTIFICATION NUMBER (VIN) PRODUCTION SERIAL NUMBER ENGINE SERIAL NUMBER WARNING (1) Model And Production Serial Number (1) Engine Serial Number The manufacturer's serial number The engine number is stamped on the...
Page 45
• In case of engine failure, engine se- rial number • Working conditions (What kind of job and how fast) The TYM genuine parts and fluid are • Run hour of machine passed severe durability and perfor- mance test. Please use TYM genuine •...
Page 52
TYM TRACTOR [HST. MODEL] Models 2515H 3015H 3515H 4215H 4815H Specification Maker A1700N6 IDI A1700N3 IDI A1700N2 IDI A2000N2 IDI A2300N2 IDI Aspiration Natural Natural Natural Natural Natural Emissions Standards Tier 4 Tier 4 Tier 4 Tier 4 Tier 4...
Page 53
CAT O Models 2515H 3015H 3515H 4215H 4815H Specification Transmission Forward/Reverse Method 4 Wheel Drive 2WD/4WD 2WD/4WD 2WD/4WD 2WD/4WD 2WD/4WD No. of Traveling Speeds 3 range 3 range 3 range 3 range 3 range Forwad Traveling Speed 15.2 (24.4) 18.7 (30.2) 18.7 (30.2) 18.7 (30.2) 18.7 (30.2)
Page 54
TYM TRACTOR Models 2515H 3015H 3515H 4215H 4815H Specification Transmission Forward/Reverse Method 4 Wheel Drive 2WD/4WD 2WD/4WD 2WD/4WD 2WD/4WD 2WD/4WD No. of Traveling Speeds 3 range 3 range 3 range 3 range 3 range Forwad Traveling Speed 15.2 (24.4) 18.7 (30.2) 18.7 (30.2)
Page 55
CAT O Models 2515H 3015H 3515H 4215H 4815H Specification 3 Point Hitch CAT I CAT I CAT I CAT I CAT I 3 Point Lift capacity at lift link ends 3,306 (1,500) 3,306 (1,500) 3,306 (1,500) 3,306 (1,500) 3,306 (1,500) lbs(kg) Hitch 3Point Hitch Lift Capacity...
Page 56
TYM TRACTOR DRIVING SPEED ※ The tractor's speed is changed by the condition of the tires and road surface. ※ To ensure safety, drive at a proper speed. [MEC. MODEL] Engine speed : 2,100 rpm (2,515) / 2,600 rpm, Tire rolling radius : 532 mm (Rear 12.4-24) km/h (mph) 11.8...
Page 57
CAT O [HST MODEL] Engine speed : 2,100 rpm (2,515) / 2,600 rpm, Tire rolling radius : 532 mm (Rear 12.4-24) km/h (mph) 12.6 24.4 OR AR (3.11) (7.82) (15.15) 12.6 24.4 (3.11) (7.82) (15.15) 15.6 30.2 OR AR (3.79) (9.69) (18.75) 15.6...
RAT O CR T O MAIN SWITCH HAZARD WARNING FLASHER SWITCH CAUTION CAUTION (1) Main Switch (A) OFF (1) Hazard Warning Flasher Switch (B) ON (C) START The main switch is used to start or stop Press the hazard flasher warning switch the engine.
TYM TRACTOR TURN SIGNAL/LAMP SWITCH SHUTTLE SHIFT LEVER [MEC. MODEL] CAUTION (1) Shuttle Shift Lever (1) Lamp Switch (A) Forward (B) Reverse (2) Turn Signal Lamp Knob ( 3 ) H o r n Button Turning the lamp switch clockwise to the...
RAT O CR T O CRUISE CONTROL SWITCH [HST MODEL] 3. When applying light pressure to the CAUTION Brake pedals, the machine’s ground speed will be reduced until the Brake pedals are released. At that point, the machine will continue at the previous ...
TYM TRACTOR HAND THROTTLE LEVER DPF REGENERATION SWITCH NOTE (1) Hand Throttle Lever (1) DPF Regeneration Switch Low Speed High Speed The hand throttle lever is to increase The DPF (diesel particulate filter) col- or decrease the engine rpm. This lever...
RAT O CR T O PTO ON/OFF SWITCH Holding the button down for more than 3 seconds initiates regeneration; the lamp turns off in 30 minutes when automatic regeneration is complete. (1) PTO ON/OFF Switch [IND]: In the IND position, the PTO shaft rotates constantly regard- less of the position of the rear implement.
TYM TRACTOR PTO INDICATOR LEFT/RIGHT TURN SIGNAL HIGH BEAM INDICATOR INDICATOR (1) PTO Indicator (1) Left Turn Signal Indicator (1) High Beam Indicator (2) Right Turn Signal Indicator This comes on when the PTO clutch This indicates the condition when op- It indicates the high beam.
RAT O CR T O PARKING BRAKE & BRAKE INDI- ENGINE OIL PRESSURE WARN- BATTERY CHARGE WARNING LAMP CATOR ING LAMP (1) Parking Brake (Brake) Indicator (1) Engine Oil Pressure Warning Lamp (1) Battery Charge Warning Lamp This comes on when the parking brake Lamp will come on when the Main The battery charge warning lamp is is applied or the brake pedal is de-...
TYM TRACTOR PREHEAT INDICATOR FUEL GAUGE TACHOMETER/HOUR METER (1) Preheat Indicator (1) Fuel Gauge (1) Tachometer (2) Hour Meter The tachometer indicates the engine Lamp will light on/off depending on This indicates the remaining fuel level. rpm and the hour meter indicates the...
RAT O CR T O COOLANT TEMPERATURE GAUGE NOTE ℃ ℃ (1) Coolant Temperature Gauge This coolant temperature gauge indi- cates the engine coolant temperature after the Main Switch is turned to the "ON" position. If the needle reads the red area, immediately stop working and then inspect the tractor.
TYM TRACTOR DPF INDICATOR CAUTION NOTE CA T O (1) DPF Indicator When an amount of soot accumulated in the DPF is over the specifi ed level, the cor- responding warning lamp on the instru- ment cluster comes on.
RAT O CR T O SENSOER ERROR INDICATION Items Lamp indication Description & Action Actives when the rpm signal is not input for cranking RPM error light on → Check rpm sensor disconnection Actives when the water temperature sensor is out of range (0.16 ~ 4.78 V) Water temperature - For this error, the water temperature is displayed at 138 degrees.
Page 76
TYM TRACTOR Items Lamp indication Description & Action Active when the position sensor of the electronic exhaust valve is out of the range (0.3 ~ 4.78V) blinking - If open circuit, the measured voltage is 0V → Please contact the service center.
RAT O CR T O CONTROLS 1(FOOT CONTROLS) [HST MODEL] (1) Brake Pedal (2) Forward Pedal (3) Backward Pedal ※ Refer to the relevant content for further detailed information...
Page 78
TYM TRACTOR [MEC. MODEL] (1) Clutch Pedal (2) Left Brake Pedal (3) Right Brake Pedal (4) Link Bracket (5) Foot Throttle Pedal ※ Refer to the relevant content for further detailed information...
RAT O CR T O F-R HST PEDAL CLUTCH PEDAL [HST. MODEL] [MEC. MODEL] CAUTION (1) HST Pedal Forward (1) Clutch Pedal (2) HST Pedal Reverse It is used for shifting between “forward” If the clutch pedal is depressed, driv- and “reverse”...
TYM TRACTOR BRAKE PEDALS (LEFT/RIGHT) FOOT THROTTLE PEDAL WARNING [MEC. MODEL] [MEC. MODEL] (1) Left Brake Pedal (2) Right Brake Pedal (1) Foot Throttle Pedal (3) Link Bracket (A) Release (B) Engage Each brake pedal is activated inde- The foot throttle pedal and the hand pendently.
RAT O CR T O CONTROLS 2 (HAND CONTROLS) [HST MODEL] (1) Range Shift Lever (2) PTO Shift Lever (3) Position control lever (4) Differential Lock Pedal (5) MFWD Lever (6) Parking Brake Lever ※ Refer to the relevant content for further detailed information...
Page 82
TYM TRACTOR [MEC. MODEL] (1) Range Shift Lever (2) PTO Shift Lever (3) Main Shift Lever (4) Position control lever (6) MFWD Lever (5) Parking Brake Lever (7) Differential Lock Pedal ※ Refer to the relevant content for further detailed information...
RAT O CR T O RANGE SHIFT LEVER PTO LEVER POSITION LEVER (1) Range Shift Lever (1) PTO Shift Lever (1) Position Control Lever 3 speeds can be selected by the range The revolution of the PTO shaft can It is used to keep the implement con- shift lever.
TYM TRACTOR MAIN SHIFT LEVER MFWD LEVER It is used to shift between 2-wheel [HST MODEL] [MEC. MODEL] drive and 4-wheel drive. Depress the clutch pedal when shifting the lever. (1) Main Shift Lever [MEC. MODEL] Four speeds can be selected by mov- ing this main shift lever in “H”...
RAT O CR T O DIFFERENTIAL LOCK PEDAL The differential lock pedal is to keep [HST MODEL] the wheel rotation on both sides the same when one of the rear wheels is idling or spinning without traction. Be sure to use the steering wheel only while the wheels are set in a straight ahead position.
TYM TRACTOR PARKING BRAKE To apply the brake, depress the [HST MODEL] brake pedals firmly and pull the lever upward. To release the brake, depress the brake pedals firmly. [MEC. MODEL] (1) Parking Brake Lever...
Page 87
5. OPERATION DAILY INSPECTION BEFORE STARTING.... 5-2 HOW TO FOLD ROPS..........5-14 CONTROL LEVER ............ 5-15 PRE-OPERATION CHECK......... 5-2 DPF REGENERATION..........5-16 PRE-OPERATION ............5-2 ATTACHMENT OF IMPLEMENT .......5-19 BEFORE STARTING THE ENGINE ......5-2 RUNNING-IN PERIOD ..........5-3 ATTACHMENT POSITION ........
TYM TRACTOR DAILY INSPECTION BEFORE PRE-OPERATION CHECK STARTING PRE-OPERATION BEFORE STARTING THE ENGINE 1. Check the engine oil level. Check the engine operation carefully. After wiping out the dipstick, insert it IMPORTANT fully and then withdraw it. Oil should be between the two marks on dip- ...
RAT O STARTING ENGINE RUNNING-IN PERIOD HOW TO START ▶ Within first 10 hours of operation IMPORTANT Inspect daily or every 10 hours Tighten the wheel bolts ▶ After first 50 hours of operation Tighten the wheel, disc and hub ...
Page 90
TYM TRACTOR [MEC. MODEL] (1) Shuttle shift lever (1) PTO ON/OFF switch (1) Position control lever (A) Lowering (B) Lifting 2. Set the shuttle shift lever in the neu- 3. Confirm that the PTO switch is set in 4. Check the position of the implement.
Page 91
RAT O [MEC. MODEL] (1) Main shift lever (1) Hand throttle lever (1) Main switch (A) OFF (B) ON Low Speed High Speed (C) START 5. Put the main shift lever in the neutral 6. Place the hand throttle lever to the 7.
TYM TRACTOR STOPPING ENGINE TRACTOR OPERATION COLD START WHEN ATTACHING WEIGHT Make sure to reduce the engine rpm CAUTION with the hand throttle lever in the Low speed position before stopping the en- gine. Depress the clutch pedal and put all shift levers in the neutral position.
RAT O REDUCE SPEED WHEN TOWING LOAD Observe the guideline for towing speed CAUTION and capacity as below. 1. If the trailed weight is the same or light- er than the tractor, maintain the maxi- mum speed of 26 km/h. 2.
TYM TRACTOR HOW TO DRIVE CAUTION [HST MODEL] (1) Safety belt (2) Seat sliding lever (1) Brake pedal [MEC. MODEL] 1. Adjust the seat properly and fasten IMPORTANT the seat belt. Adjust the seat to eas- ily reach the pedal and the steering wheel.
Page 95
RAT O 2. Check if both brake pedals are inter- locked. (1) Position Control lever (1) Hand throttle lever (A) Engine rpm increases 3. Lift the implement. To lift the installed 4. Control the hand throttle lever. I n - implement, pull the control lever crease the engine rpm from low to backward.
Page 96
TYM TRACTOR [MEC. MODEL] [MEC. MODEL] [HST MODEL] (1) Main shift lever (2) Range shift lever (1) Shuttle shift lever [MEC. MODEL] (A) Forward (B) Reverse 6. Put the main and range shift levers 7. Operate the shuttle shift lever. This le-...
RAT O STOPPING 1. Stop the tractor with the brake pedal 8. Make sure the parking brake is ap- CAUTION and clutch pedal. plied. 2. Put the main shift lever to the neutral 9. Turn the main switch to the OFF posi- ...
TYM TRACTOR PARKING When parking the tractor, securely en- IMPORTANT [HST MODEL] gage the parking brake by pulling the parking brake lever completely. To re- lease the parking brake, depress the parking brake pedal firmly. CAUTION [MEC. MODEL] CAUTION ...
RAT O DIFFERENTIAL LOCK 3. If the tire is rotating idle repeatedly, try [HST MODEL] CAUTION to engage the differential lock again. IMPORTANT [MEC. MODEL] 1. When the speed at one wheel starts to drop, depress the differential lock pedal to activate the differential lock.
TYM TRACTOR HOW.TO.FOLD.ROPS CAUTION 3. Fit the pins (5) through the holes of 1. Loosen the bolt (3) and nut (6) of the the frames (1 & 7) and fit the snap frame. (Do not unscrew them com- pins (4) into the holes of the pins (5) pletely.)
RAT O CONTROL LEVER • If the safety frame is incorrectly in- CAUTION stalled, it can lead to a severe acci- dent during a rollover accident. • Make sure to install the bolts, pins and nuts properly to set the safety frame upright securely.
TYM TRACTOR DPF REGENERATION Keep above 3,000 rpm with Accel Le- ver. However, the following condi- When the DPF regeneration is com- tions must be satisfied. pleted, the regeneration lamp is turned off on the instrument panel. Parking on ...
Page 103
RAT O DPF REGENERATION INDICATION Items Lamp Indication Description If the DPF has more than a certain amount of soot, it informs DPF regeneration Light on the driver that it is time to regenerate. time reached [Buzzer] Buzzer sounds 3 times every minute. If driver press the regeneration button for more than 3 DPF regeneration seconds in high idle (2,850 rpm or more), driver can enter...
Page 104
TYM TRACTOR ERROR DISPLAY DURING DPF REGENERATION Items Lamp Indication Description Actives when the cooling water temperature exceeds 105 de- grees during DPF regeneration. You can not retry regenera- Engine overheating Blinking tion within 10 minutes. [Buzzer] Repeat 1Sec Sound On→0.5 Sec Sound Off, and if it goes below 100 degrees, Buzzer is turned off.
TYM TRACTOR TOP LINK ADJUSTMENT ATTACHING IMPLEMENT C: If the Top link is attached to the top position, the draft system will not be activated. This is good for the implement such as a drilling ma- chine or equivalent which does not require any traction force.
Page 107
RAT O WARNING IMPORTANT (1) Top link (2) Fixing bracket 4. Detach the Top link from the fixing bracket. 5. Attach the Top link to the top mast of the implement. 6. Adjust the length of the Top link and lower link if required.
TYM TRACTOR ADJUSTMENT OF STABILIZER ADJUSTMENT OF VERTICAL HEIGHT CAUTION (1) Stabilizer (1) Rectangular steel plate 1. For implements such as a plow and 1. To let the implement float along con- disc harrow, adjust the length so that tour of the ground, turn the rectangu- it can be moved for 5 - 6 cm sideways.
RAT O POSITIONING OF DRAW BAR INSTALLATION OF PTO DRIVEN IMPLEMENT 3. When towing a heavy load, tow it with 1. Attach the implement to the tractor. shortest draw bar position. 2. Lift the implement off the ground. 3. Stop the engine and put the PTO shift lever in the neutral position.
TYM TRACTOR HOW TO CONNECT HYDRAULIC HOSE FOR LOADER ATTACHMENT HYDRAULIC CIRCUIT OF FRONT CAUTION OUTLET VALVE Before connecting loader hydraulic hose (1) R2 (2) R1 (3) P2 (4) P1 (5) T OCAT O CAUTION After connecting loader hydraulic hose ...
RAT O TIRES, WHEELS AND BALLAST TIRE TYPE PROPER INFLATION PRESSURE When installing a loader, the plug of the port R1 should be fit to the port Inflation R2 to enable correct operation of the Tire size pressure loader. (㎏/cm CAUTION 7-16/8-16 11.2-24/...
TYM TRACTOR WHEEL AND AXLE FRONT WHEEL ASSEMBLY REAR WHEEL ASSEMBLY If the wheel or axle is loosened, tighten to the specified torque. Front Front Remarks Remarks 1. Drive the tractor about 100 m and tight- wheel wheel en it to the specified torque.
Page 113
6. MAINTENANCE MAINTENANCE SCHEDULE CHART....6-2 CHECKING EXHAUST GAS........6-14 CHECKING FUSE AND FUSIBLE LINK...... 6-14 FLUIDS............6-4 CHECKING AND ADJUSTING TOE-IN ...... 6-15 CHECKING AND ADJUSTING FAN BELT ....6-15 FLUIDS AND CAPACITY..........6-4 ROUTINE MAINTENANCE........ 6-5 OPENING HOOD............
TYM TRACTOR MAINTENANCE SCHEDULE CHART ⃝ : Check‧Add‧Adjust ● : Replace ★ : Replace at first time only △ : Clean HOUR YEAR INSPECTION PART ENGINE OIL LEVEL CHECK BEFORE EVERY WORK ENGINE OIL & FITER ★ ● ● ●...
Page 115
MA T ⃝ : Check‧Add‧Adjust ● : Replace ★ : Replace at first time only △ : Clean HOUR YEAR INSPECTION PART TRANSMISSON OIL ★ ⃝ ⃝ ⃝ ⃝ ⃝ ● ⃝ ⃝ ⃝ ⃝ ⃝ ● ⃝ TRANSMISSON OIL FILTER ★...
MA T ROUTINE MAINTENANCE OPENING HOOD CHECKING AND REPLACING ENGINE OIL CHECKING REPLACING (1) Opening knob (1) Oil dipstick (2) Oil inlet (1) Drain plug 1. The hood can be unlocked by pull- Pull out the oil dipstick, clean it, and To drain oil, remove the drain plug on ing the opening knob.
TYM TRACTOR CHECKING AND CHANGING TRANSMISSION FLUID CHECKING CHANGING Pull out the dipstick from the top of Drain transmission fluid by removing the rear axle housing on the left. Then, the drain plug from the transmission or rear axle case. Change transmission...
MA T CHECKING AND CHANGING FRONT AXLE OIL REPLACING ENGINE OIL FILTER CHECKING CHANGING (1) Filler plug (1) Drain plug (1) Oil filter cartridge (A) Upper limit (B) Lower limit (C) Specified level Unscrew the oil filler plugs on the left To drain the used oil, remove the right 1.
TYM TRACTOR REPLACING TRANSMISSION FLUID FILTER 4. Check the engine oil level again with 1. After draining transmission oil, re- [MEC. MODEL] the oil dipstick after the hydraulic pi- move the oil filter cartridge by turning lot lamp is turned off. If the level is low, it counterclockwise.
MA T CHECKING AND CHANGING COOLANT CHECKING REPLACEMENT PROCEDURE 1. To drain coolant, open the radiator cap and drain plug and drain cool- ant completely from the radiator. 2. Flush the radiator until clean water is drained. 3. Add anti-freeze up to the filler neck of the radiator.
TYM TRACTOR CHECKING AND ADDING FUEL CHECKING BATTERY DANGER (1) Fuel cap (1) Ground cable (-) (2) Thick red wire (+) Turn the main switch to the "ON" posi- Check if the electrolyte level is within tion. If the fuel gauge needle is pointing...
MA T CHECKING HOSES AND PIPES CHECKING ELECTRIC WIRING Check the fuel hose, hydraulic steering Open the hood and check if any ca- CAUTION wheel hose (pipe), radiator hose, etc. ble is in contact with other parts, or if for damage or leakage. Check if there any insulation is peeled off or dam- ...
TYM TRACTOR GREASING CHECKING AND ADJUSTING CHECKING AND ADJUSTING STEERING WHEEL BRAKE [HST MODEL] (1) Nipple (A) Free play of steering wheel [MEC. MODEL] Apply grease every 50 hours. Check the When the steering wheel is turned to the relevant parts (9 points) before starting...
MA T CLEANING FUEL FILTER SEPARATOR The free play of the brake pedal is 5 - If moisture is found in the filter 10 mm. Adjust both brake pedals at the head(2), remove the foreign matter as same time. follows. (1) Turn off the starter to prevent air from entering the fuel system.
TYM TRACTOR CHECKING EXHAUST GAS CHECKING FUSE AND FUSIBLE LINK Exhaust gas may be a little black at the When replacing the fuse, use only the [HST MODEL] time of starting the engine, but nor- one with the specified capacity. Open the mally it is colorless.
MA T CHECKING AND ADJUSTING CHECKING AND ADJUSTING TOE-IN FAN BELT Tighten the nuts when the toe-in is 0.2 - 0.3 in. (4 - 8 mm). Be sure of both lengths of the left and right tie rod ends are the same.
Page 130
TYM TRACTOR TROUBLESHOOTING - ENGINE Symptom Inspection item Action Depress the clutch pedal fully and turn the igni- Is the clutch depressed? tion switch to the "START" position. Is the battery discharged? Charge the battery. 1. The starter motor Is the battery terminal loosened or corroded? Clean and tighten the terminals.
Page 131
Symptom Inspection item Action Is the coolant level low? Refill the coolant. Is the fan belt loosened or damaged? Adjust the belt tension or replace it. 4. The engine is over- Is the radiator fin clogged? Clean it.
Page 132
TYM TRACTOR Symptom Inspection item Action 6. The coolant warn- ing lamp wis turned Is the coolant level in the reservoir tank low? Refill the coolant. “ON” during opera- tion. Is the engine oil level low? Refill the engine oil up to required level.
Page 133
TROUBLESHOOTING - CLUTCH AND BRAKE Symptom Inspection item Action 1. The clutch slips or does not be Is the free play of clutch pedal proper? Adjust the free play of the pedals. disengaged. 2. The brake does not work or works Is the free play of the brake pedals proper? Adjust the free play of the pedals.
Page 134
TYM TRACTOR TROUBLESHOOTING - HYDRAULIC SYSTEM Symptom Inspection item Action Is the hydraulic flow control dial in the close Adjust the hydraulic flow control dial. position? Is the transmission oil level low? Refill the transmission oil. ...
Page 135
TROUBLESHOOTING - ELECTRIC SYSTEM Symptom Inspection item Action Is the bulb blown? Replace the bulb. Is the fuse blown? Replace the fuse. 1. The headlamp does not turn “ON”. Is the cable connector separated from the socket? Inspect it.
TYM TRACTOR DAILY.STORAGE 1. Store the tractor after cleaning it. DANGER Especially, clean it thoroughly after When covering the tractor, make harrowing or working in a wet fi eld. Don’t forget to dry sure that the engine or the muffl er off and grease the 2.
TORA LONG-TERM STORAGE In particular, we recommend that the electrical cables and the rubber hoses, such as fuel hose, steering hoses and Maintenance Remove radiator hoses, be replaced every two Annually Best & years. condition If you carry out maintenance during If the tractor is not used for a long the off season, you can ensure opti- time, store it in the following manner.
Page 140
TYM TRACTOR 3. Fill up the fuel tank. Empty space in 8. Add oil, fluid and fuel to each part the fuel tank will produce dewdrops according to the maintenance chart. that will produce condensation that will be the cause of rust forma- 9.
Page 141
TORA IMPORTANT WARNING CAUTION To avoid a personal injury, WARNING ...
TYM TRACTOR OPERATING TRACTOR AFTER LONG-TERM STORAGE Keep the following instructions when op- 10. Start the engine, release the park- WARNING erating the tractor after its long-term stor- ing brake, and check the brake con- When operating the tractor in an en- age.
TORA USAGE AND DISPOSAL It is recommended to keep the following to protect the environment: 1. Overload on the machine shortens the product life and increases the harmful exhaust gas which causes air pollution due to the incomplete combustion. 2. When changing the fluid (engine oil, transmission/hydraulic oil, and engine coolant) by yourself, be careful not to spill it and dispose used oil and cool-...
9. EMISSIONS CONTROL WARRANTY EMISSIONS CONTROL WARRANTY ..........9-2...
Page 146
ACT R R ARRA TY CO TYM warrants to the original owner, and to each subsequent owner, of a new, diesel engine that the emission control system of your engine: 1. Was designed, built and equipped so as to conform at the time of sale with all applicable regula-...
Page 147
• This engine is designed to operate on diesel fuel only. Use of any other fuel may result in the engine no longer operating in compliance with EPA’s applicable emissions requirements. • The purchaser is responsible for initiating the warranty process. You must present the engine to a TYM dealer as soon as a problem exists.
Page 148
• The use of any non-exempted add-on or modifi ed parts shall be grounds for disallowing a warranty claim. TYM is not liable for failures of warranted parts caused by the use of a non-exempted add-on or modifi ed part.
Page 149
CO TRO ARRA TY ART CO ARRA TY The following is a list of emission control parts that are covered by the Limited Emission Control System Warranty. This warranty covers include any engine parts related to the following systems: - Fuel Injection Pump - Turbocharger (if equipped) - Fuel Injectors - Charge air cooling system (if equipped)
Need help?
Do you have a question about the 2515R and is the answer not in the manual?
Questions and answers
I want to remove WIFO pull behind snowblower from TYM 2515R. Having a lot of trouble. Pins are real tight so can't even get started.
To remove the WIFO pull-behind snowblower from a TYM 2515R when the pins are tight, move the draw bar forward and backward to help align and release the lock pin. This may reduce tension and allow the pin to be removed more easily.
This answer is automatically generated
Where do I find the drain plug for my radiator on the TYM 2515?