Table of Contents
Advertisement
Quick Links
(
Operating
Instructions
_
STEREO DOUBLE CASSETTE
TAPE DECK
CT-SSSWR
•
Photograph shows
BLACK
finished model
•
Only the
DI
G
(U.S.
Military) model
comes
with
the side
panels.
"This
product
is
manufactured to
comply
with the radio in-
terference requirements
of
EEC Directive
761889/
EEC
and
82/ 499/
EEC."
Th,ank.you
for.
tiuying this
Pioneer
product.
Please
read.these Ol'lerating instructions
thoroughly,
so you
will know
how to.operate your model
properly.
After
you have finished
reading
t~e
instr~ctions
,
put them
away in a safe
place
for.future
reference
.
For
the
5ake
of convenience,
these
operating
instructions are based
on.the model HEM, and they can be used for the HB, HP, KU, KC,
D
and
DI
G models.
The differences
betweerr-the
models
are
given
below.
HEM
model
:
For
Europe
excluding
U.K.
('
HEM
'
stamped on packing
cas.
e ):
Power
line voltage
is
AC 220
volts.
HB
model:
For U
.K. ('HB' stamped
on
packing
case):
Power
line voltage
is AC
240
vo
lts
.
HP
model:
For
Australia
('HP'
stamped
on
packing
case)
:
Power
line
voltage is
AC
240
volts
.
KU and KC
models
:
For U.S.A. and
Canada
('KU' or
' KC'
stamped on
packing case):
Power line voltage is
AC 120
volts
.
D
and D
I
G models
:
For destination
s excluding
above ('D' or
'
DI
G' stamped on packing
case):
A 3-point (1
20
V
l
220
V
l
240
V) voltage selector
switch
is pr;-
vided
.
NOTE:
Depending upon the model, the design
of
the power plug and the
power outlet
differs.
The
line voltage selector switch
is located on the rear panel of the
unit.
Please
check
that it is
set
properly before plugging the power
cord
into
an outlet.
If
it is not set
properly,
change
the setting
of
it
according
to the
LINE
VOLTAGE
SELECTION
(D
and D
I
G models
only).
IMPORTANT NOTICE
(For KU
and KC
models)
The
serial number
for this equipment
is
located on the rear
panel.
Please write
this serial number on your enclosed warranty card and
keep in
a
secu re
pla
ce.
This
is for
your
security.
'"\_
WARNING: TO PREVENT
FIRE OR
SHOCK HAZARD,
DO NOT EXPOSE
THIS
APPLIANCE
TO RAIN OR
MOISTURE.
LINE VOLTAGE
SELECTION
(0
and D/G models
only)
Before your model is shipped
from
the factory,
the switch
is
set
to
the
power requirements
of
the
destination;
nevertheless,
you should
check
th;;it it is set properly before plugging
the power cord into
the
AC
outlet.
1. Disconnect the power cord
.
2.
Provide yourself with
a
medium size screwdriver.
3. Insert
the
screwdriver
into
the groove
on
the voltage selector
and
adjust to the voltage
value
of
your area.
HEM (for
Europe
excluding U.K.),
HB
(fo
r U
.K.),
HP (for
Australia), KU
(for
U .S.A.) and KC
(for
Canada)
models
are
not
provided with a LINE VOLTAGE SE,LECTOR switch.
{\DPIONEER~
Advertisement
Table of Contents
