Advertisement
Quick Links
ONE DISC USER MANUAL
Ventum One Disc Torque Specs
▼ Seatpost clamp: 6-8 Nm
▼ 2 nose-cone side bolts: hand tight
▼ Mono-riser bolts (behind the nose cone): 7 Nm
▼ Mast tilt bolts (between arm pads): 7 Nm
▼ Base bar bolts: 7 Nm
▼ Aero-extension holder bolts: 5 Nm
▼ Arm cup/pad bolts: 3 Nm
▼ Stem bolts: 6-8 Nm
▼ TRP brake lever bolts (on base bar): 3 Nm
Advertisement
Related Manuals for Ventum One
Summary of Contents for Ventum One
- Page 1 ONE DISC USER MANUAL Ventum One Disc Torque Specs ▼ Seatpost clamp: 6-8 Nm ▼ Aero-extension holder bolts: 5 Nm ▼ 2 nose-cone side bolts: hand tight ▼ Arm cup/pad bolts: 3 Nm ▼ Mono-riser bolts (behind the nose cone): 7 Nm ▼...
-
Page 2: Seatpost Clamp
Ventum One Disc User Manual Congratulations on your purchase of the Ventum One Bike! This document will guide you through the process of setting up your new bike and getting out on the road. Of course, if you have any questions or if we can be of assistance in any way, please contact the Ventum Concierge team at support@ventumracing.com. - Page 3 Nose-cone side bolts ▼ Position the nose cone as shown ▼ Hand tighten the nose cone side bolts Mono-riser bolts ▼ Position the mast clamp as shown ▼ Torque the mono-riser bolts to 7 Nm One Disc User Manual...
- Page 4 Mast tilt bolts ▼ Position the armrest mount as shown ▼ Torque the mast tilt bolts to 7 Nm Base bar bolts ▼ Torque the base bar bolts to 7 Nm One Disc User Manual...
- Page 5 Aero extension holder bolts ▼ Torque the aero extension holder bolts to 5 Nm Arm cup/pad bolts ▼ Torque the arm cup bolts to 3 Nm One Disc User Manual...
- Page 6 Stem bolts ▼ Torque the stem bolts to 6 N.m.. If necessary, they can be torqued up to 8 Nm TRP brake lever bolts ▼ Torque the brake lever bolts to 3 Nm One Disc User Manual...
- Page 7 ▼ Torque the right screw to 7 Nm Mast height ▼ Loosen the mono-riser bolts until the riser post can slide freely ▼ Adjust the mast until it is at the desired height ▼ Torque the mono-riser bolts to 7 Nm One Disc User Manual...
- Page 8 ▼ Place 1mm thick washers under the ▼ Torque the bottle bracket screws to 1 or 2 Nm bottle bracket as shown Front thru axle Rear thru axle ▼ Install the thru axles and torque to 10 Nm One Disc User Manual...
- Page 9 ▼ A: Right Etap/Di2 cable ▼ B: Left Etap/Di2 cable through these ports ▼ B: It is recommended to route the Di2/Etap ▼ C: Front brake cable cables through these ports ▼ D: Rear brake cable One Disc User Manual...
- Page 10 ▼ A: Top of stem ▼ B: Mast riser ▼ C: Bottom of stem ▼ D, E, F, G: Etap/Di2 cables One Disc User Manual...
- Page 11 This can be done by using the index finger to guide the wires to either side of the mast while installing it into the stem. ▼ Route cables from extensions into the stem and under the basebar nut plate within the stem out to the Blipbox/B-junction. One Disc User Manual...
- Page 12 ONE DISC USER MANUAL Please contact the Ventum Concierge team at support@ventumracing.com. Before you hit the road, please also take a moment to register your bike purchase via our website: https://ventumracing.com/register-your-bike/...