Toshiba RAS-22 Owner's Manual page 4

INDOOR UNIT DISPLAY
1
1 ECO (White)
2 1
2 Wi-Fi access (White)
3 Hi POWER (White)
4 Timer (White)
5 Operation (White)
4
3 5
Display brightness can be adjusted, follow procedure on !.
●
Require Wireless LAN connecting adapter which available as accessory.
PREPARATION BEFORE USE
2
Preparing Filters
1. Open the air inlet grille and remove the air filters.
2. Attach the filters. (see detail in the installation manual).
Loading Batteries (when use wireless operation.)
1. Remove the slide cover.
2. Insert 2 new batteries (AAA type)
following the (+) and (–) positions.
Clock Setup
1. Push by tip of the pencil.
If timer indication is flashing, go to the next step 2.
2. Press or : adjust the time.
3. Press : Set the time.
Remote Control Reset
Push by tip of the pencil or
1. Remove the batteries.
2. Press .
3. Insert the batteries.
3 AIR FLOW DIRECTION
1
Press : Move the louver
in the desired vertical direction.
Press : Move the
2
louver in the desired horizontal
direction.
Press : For select
louver swing operation.
Vertical Horizontal
3
(Up-Down) (Left-Right)
Swing Swing
Up-Down
Swing off Left-Right
Swing
Press : To select provided air flow direciton
Wide Spot Wide
center left left
4
"Pi" sound when air flow direction is set and "PiPi" sound when
air flow direction is canceled and return to manually setting.
Note:
Do not move the louver manually by hands or others.
●
The louver may automation positioning by some operation mode.
●
● Vertical (Up-Down) swing
● Horizontal (Left-Right) swing
Spot Wide Spot Return to
center right right manually setting
REMOTE CONTROL
4
Infrared signal emitter
1
Start/Stop button (
)
2
Mode select button ( )
3
Temperature button ( )
4
Fan speed button ( )
5
Swing louver button ( )
6
Set louver Up-Down button (
7
On timer button ( )
8
Off timer button ( )
9
Setup button ( )
0
Clear button ( )
!
Memory and Preset button (
@
AIR FLOW selection button (
#
High power button ( )
$
Economy button ( )
%
Set louver Left-Right button (
^
Comfort sleep button ( )
&
Filter reset button ( )
*
Set clock button ( )
(
Check button ( )
)
Reset button ( )
-
Note:
The provided Remote Controller is a wireless type, which also can be
●
used as a wire. Please see "How to Connect The Remote Controller for
Wired Operation", located in installation instruction, in case of wired
control is required.
In wire operation, remote controller will return to initial condition (PRESET,
●
TIMER and CLOCK will return to initial condition) when user shutdown
power supply of Air conditioner.
5 AUTOMATIC OPERATION
To automatically select cooling, or fan only operation
1. Press : Select Auto A.
2. Press : Set the desired temperature Min. 17°C, Max. 30°C.
3. Press : Select AUTO, LOW , LOW+
MED+ , HIGH
COOLING / FAN ONLY OPERATION
6
1. Press : Select Cool
2. Press : Set the desired temperature.
Cooling: Min. 17°C, Max. 30°C
Fan Only: No temperature indication
3. Press : Select AUTO, LOW , LOW+
MED+ , HIGH
7 DRY OPERATION
For dehumidification, a moderate cooling performance is controlled
automatically.
1. Press : Select Dry
2. Press : Set the desired temperature Min. 17°C, Max. 30°C.
Note: Dry mode fan speed is set to Auto only.
8 Hi-POWER OPERATION
To automatically control room temperature and airflow for faster cooling
operation (except in DRY and FAN ONLY mode)
Press : Start and stop the operation.
)
)
)
)
, MED ,
or Quiet .
or Fan only .
, MED
or Quiet .
.
,