Related Manuals for Sonotec BS30
Summary of Contents for Sonotec BS30
- Page 1 Operating Manual BS30 Broadband parabolic sensor for the SONAPHONE handheld unit Translation of the German Original Revision: 2.1 | 2023-04-27...
-
Page 2: Table Of Contents
Operating Manual | Content BS30 Content Introduction ........................3 Notes on this documentation ..................3 Representations in this documentation ................ 3 Identification of warning instructions ................4 Safety instructions ......................5 Introduction ........................5 Basic hazards ........................5 Personnel and qualifications ..................6 Safety-conscious working practices ................ -
Page 3: Introduction
Operating Manual | 1 Introduction BS30 1 Introduction This section is intended to explain function, structure and representations of this documentation to simplify handling of this documentation. Notes on this documentation Purpose This documentation constitutes an integral part of the product and contains important advice on safe operation as well as all information on intended and efficient use. -
Page 4: Identification Of Warning Instructions
Operating Manual | 1 Introduction BS30 1.3 Identification of warning instructions Classes of danger, signal words and colors This documentation contains warnings regarding hazards of different classifications. These classes are characterized by signal words and colors. They include the following:... -
Page 5: Safety Instructions
Operating Manual | 2 Safety instructions BS30 2 Safety instructions This section contains safety information relating to the protection of persons as well as safe and fault-free operation. All user groups of the product must be aware of and follow these safety provisions. -
Page 6: Personnel And Qualifications
Operating Manual | 2 Safety instructions BS30 2.3 Personnel and qualifications Basic requirements The product must only be used by operators that have completely read and understood the safety instructions and all documents of the user documentation. Personnel undergoing training or instructions or persons taking part in general vocational training programs may only operate the device under the continuous supervision of operating or technical personnel. -
Page 7: Use Of The Product
Do not use the product and its accessories if they display functional errors and/or visible damage. • Only connect the product to approved equipment received from SONOTEC GmbH or its sales partners. • The product adheres to the protection class given in the technical specification and is not protected against water. -
Page 8: Modifications And Alterations
Spare parts and accessories Spare parts and accessories must comply with the technical requirements specified by SONOTEC GmbH and its suppliers. Whenever original parts are used, compliance is given. 8 / 25 Revision: 2.1 | 2023-04-27... -
Page 9: Description Of The Sensor
The integrated class 2 target laser and a red/green dot sight support locating test sites. 3.2 Prohibited use Any use not approved by SONOTEC GmbH is prohibited and may lead to injury or damage to property. SONOTEC GmbH accepts no liability for damage caused by prohibited use of the product. -
Page 10: Working Principle
The position of the damaged area will thus be marked by either the target laser or the red/green dot sight. 3.4 Sensor construction Operating elements Figure 1: Operating elements of the BS30 Description/function Starts/stops a measurement value recording. Switches on the target laser (keep the button pressed) Status LED •... - Page 11 Operating Manual | 3 Description of the sensor BS30 Sensor elements Figure 2: Sensor elements of the BS30 Description/function Parabolic reflector with mirror carriage and locking screw Red/green dot sight with optionally either green or red dot and five brightness levels...
-
Page 12: Sensor Identification
Operating Manual | 3 Description of the sensor BS30 Connections Figure 3: Connections of the BS30 Description/function USB port • Type: Micro-USB socket, type B • for service purposes only Sensor cable socket • Type: LEMO 0B (4-pin) • with marked plug-in position 3.5 Sensor identification... -
Page 13: Operation Of The Sensor
Operating Manual | 4 Operation of the sensor BS30 4 Operation of the sensor This section contains descriptions and instructions for operating the sensor and using it in combination with the SONAPHONE handheld unit. WARNING Risk of injury to eyes by target laser! The target laser (laser class 2) can cause serious eye damage. - Page 14 Operating Manual | 4 Operation of the sensor BS30 Tighten the control wheel to fix the parabolic reflector in its position. Removal Hold the sensor handle with one hand, and with the other hand, loosen the mirror carriage's locking screw.
-
Page 15: Connecting The Sensor
Operating Manual | 4 Operation of the sensor BS30 4.2 Connecting the sensor ATTENTION Risk of damage to sensor and/or sensor cable! When connecting the sensor, always mind the red markings on the sockets of the sensor and the SONAPHONE handheld unit as well as the sensor cable. -
Page 16: Operation Via Sensor Buttons
Operating Manual | 4 Operation of the sensor BS30 4.3 Operation via sensor buttons Measurements may be controlled either via the touch screen of the SONAPHONE handheld unit or the sensor buttons. The sensor buttons provide the following functions: •... -
Page 17: Using The Target Laser And Red/Green Dot Sight
Operating Manual | 4 Operation of the sensor BS30 4.4 Using the target laser and red/green dot sight Description Target laser and red/green dot sight are two separate options for precisely locating damaged areas. Among others, the choice of option depends on the system's dimensions, the distance from the damaged area, the lighting conditions and personal preferences. - Page 18 Operating Manual | 4 Operation of the sensor BS30 Switching on Remove the protective caps from the red/green dot sight. Use the brightness control to set the requested color (red or green) and the dot intensity. After use Switch off the red/green dot sight by turning the brightness control to the R or G position.
-
Page 19: Cleaning And Maintenance
ATTENTION Check the compatibility of used cleaning agents! The compatibility of all cleaning agents with used materials and colors must be confirmed and approved by SONOTEC GmbH or the respective supplier. Unsuitable cleaning agents Do not clean the product with: •... -
Page 20: Maintenance
Operating Manual | 5 Cleaning and maintenance BS30 5.2 Maintenance Guidelines Do not open the device! The device contains no parts to be maintained or repaired by the operator. Replacing the red/green dot sight's battery For replacing the battery, please refer to the manufacturer's operating manual. -
Page 21: Technical Data
-10 … +65 °C Storage temperature -20 … +65 °C (up to 40 °C at 90 % humidity) Protection type IP40 Order details Scope of delivery • Broadband parabolic sensor BS30 • Calibration certificate 21 / 25 Revision: 2.1 | 2023-04-27... - Page 22 Operating Manual | 6 Technical data BS30 Technical drawing 22 / 25 Revision: 2.1 | 2023-04-27...
-
Page 23: Disposal
Operating Manual | 7 Disposal BS30 7 Disposal Recycling and taking back of used equipment Electrical and electronic devices may pose a risk to health and the environment if disposed of incorrectly. They cannot therefore be disposed of as domestic waste according to WEEE Directive 2012/19/EU (Waste Electrical and Electronic Equipment Directive). -
Page 24: Warranty
Warranty During the warranty period, SONOTEC GmbH will eliminate all deficiencies caused by material or manufacturing faults free of charge. SONOTEC GmbH will at its own discretion offer warranty by reparation or replacement of faulty products. Exceptions Internal accumulators as well as damage caused by unintended use, by wear or by manipulation of the product are exempt from warranty. -
Page 25: Manufacturer Information
© SONOTEC GmbH All rights reserved. All contents of this document are property of SONOTEC GmbH and are protected by copyright. Duplication, modification and/or distribution in any form, particularly for reprint, for photographic, mechanical or electronic reproduction or in the form of saving in data processing systems or data networks is forbidden without written approval by SONOTEC GmbH.
Need help?
Do you have a question about the BS30 and is the answer not in the manual?
Questions and answers