Sealey LVLP-990 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND
CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY
CAUSE DAMAGE OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
Familiarise yourself with this products application and limitations, as well as the specific potential hazards peculiar to the spray gun.
WARNING! Disconnect the spray gun from the air supply before changing accessories, servicing or performing any maintenance.
3
Paint cup remains pressurised after gun is disconnected from air line. DO NOT pull the trigger, but depressurise by gently opening cup.
p
Maintain the spray gun in good condition (use an authorised service agent).
3
Replace or repair damaged parts. Use recommended parts only. Non-authorised parts may be dangerous and will invalidate the warranty.
3
Keep the spray gun clean for best and safest performance.
3
Ensure the air system is compatible with the spray gun air consumption (269l/min - 9.5cfm).
3
Wear approved safety respiratory protection and safety goggles.
3
Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and tie back long hair.
3
Locate the spray gun in a suitable working area, keep area clean and tidy and free from unrelated materials and ensure there is adequate
3
ventilation and lighting.
3
Keep children and unauthorised persons away from the working area.
When not in use ensure the air supply is turned off.
3
Avoid unintentional operation.
3
DO NOT point spray gun at yourself, at other persons or animals.
3
DO NOT carry the spray gun by the hose, or yank the hose from the air supply.
7
DO NOT use the spray gun for any purpose other than for which it is designed.
7
DO NOT allow untrained persons to operate the spray gun.
7
DO NOT get the spray gun wet or use in damp or wet locations or areas where there is condensation.
7
DO NOT operate the spray gun if any parts are missing or damaged as this may cause failure or possible personal injury.
7
DO NOT direct air from the air hose at yourself or at others.
7
When not in use switch the spray gun off and disconnect from the air supply.
7
3
2. DESCRIPTION & SPECIFICATIONS
The LVLP spray gun has an anodised body, which resists corrosion and has a low affinity for paint making the unit easy to clean, and adjustable
paint and fan width controls. LVLP (Low Volume - Low Pressure) technology uses far less air and the gun is compatible with compressors as
small as 3.5hp/2.6kW. Suitable for use with water based paints.
2.1. Specifications
Model LVLP-990 Suction Feed
Standard set-up . . . . . . . . . . . . . . .1.7mm
Available set-ups . . . . . . . . . . . .1.5,1.9mm
Air pressure . . . . . . . . . . . . . . .2 bar/30psi
Air consumption . . . . . . . . . . . . . . .9.5cfm
Max. operating pressure . . . . . .4 bar/58psi
3. AIR SUPPLY CONNECTION
3.1. Ensure the air valve is in the "off" position before connecting to the air supply.
3.2. You will require an air pressure of
3.3. p WARNING! Ensure the air is clean and the pressure does not exceed 4 bar/58psi. Too high an air pressure and unclean air will shorten
the product life due to excessive wear, and may be dangerous, possibly causing damage and personal injury.
3.4. Drain the air tank daily. Water in the air line may damage the gun and will contaminate the paint.
3.5. Clean the air inlet filter screen weekly. The recommended hook-up procedure is shown.
3.6. Line pressure should be increased to compensate for
unusually long air hoses (over 8 metres).
The minimum hose diameter should be 10mm I.D.
and fittings must have the same inside dimensions.
3.7. Keep hoses away from heat, oil and sharp edges.
Check hoses for wear and make certain that all
connections are secure.
2 bar/30psi , and an air supply of
INSTRUCTIONS FOR:
LV L P S P R AY G U N
LVLP-990 & LVLP-991
Models:
Model LVLP-991 Gravity Feed
Standard set-up . . . . . . . . . . . . . . .1.5mm
Available set-ups . . . . . . . . .1.3,1.7,1.9mm
Air pressure . . . . . . . . . . . . . . .2 bar/30psi
Air consumption . . . . . . . . . . . . . . .9.5cfm
Max. operating pressure . . . . . .4 bar/58psi
9.5cfm to operate the spray gun.
LVLP-990/991 - 0004 - (1) - 191099