Subscribe to Our Youtube Channel
Related Manuals for Ocular IOCAH10-7S
Summary of Contents for Ocular IOCAH10-7S
- Page 1 OCULAR IQ WALLBOX INSTALLATION GUIDE IOCAH10-7S/7T & IOCAH10-22S/22T OCULAR CHARGING AUSTRALIA Email: sales@ocularcharging.com.au Web: www.ocularcharging.com.au...
-
Page 2: Table Of Contents
CONTENTS ..................SPECIFICATIONS ....................FEATURES ................PRODUCT OVERVIEW ................SAFETY INSTRUCTIONS IMPORTANT ! ................... INSTALLATION READ THIS ENTIRE DOCUMENT BEFORE INSTALLING OR USING ..................NOTES BEFORE INSTALLATION THE CHARGER. FAILURE TO DO SO OR TO FOLLOW ANY OF THE ......................TOOLS REQUIRED INSTRUCTIONS AND WARNINGS IN THIS DOCUMENT CAN ....................... -
Page 3: Specifications
All specifications and descriptions contained in this document are verified to be accurate at the time of printing. However, because continuous improvement is a goal at Ocular Charging, we reserve the right to make product modifications at any time. Model... -
Page 4: Features
SELF-MONITORING AND RECOVERY PRODUCT OVERVIEW The charger will automatically resume charging after a minor fault such as OVP, UVP, OTP or OCP, with no user intervention required. OCPP 1.6J FULL PROFILES & SMART CHARGING SUPPORT The charger supports OCPP 1.6J including the latest smart charging profile to balance the load of charging stations with limited power supply. - Page 5 SAVE THESE IMPORTANT SAFETY INSTRUCTIONS This document contains important instructions and warnings that must be followed when installing and maintaining the workplace pedestal charger CAUTIONS: WARNINGS: Do not install or use the charger near flammable, explosive, harsh, or combustible The charger should be installed only by a qualified approved technician. materials, chemicals, or vapors.
- Page 6 Regarding the installation of the Ocular IQ Wallbox, each charger will need a power connection and additional internet connection to allow smart charging with Energy Tracking , Smart Control and Load Management. Power connection Internet connection (required for smart functions) Regarding the power connection of the chargers, each charger will have its own designated circuit from the distribution board as per required in Appendix P, AS 3000:2018 Australia Standard for EV charging stations.
-
Page 7: Installation
NOTES BEFORE INSTALLATION STEP ONE - CHECK BOX CONTENTS The charger should be protected by an external Residual Current If any of these components are damaged or missing, contact Ocular Device (RCD) to be installed in the upstream circuit which complies Charging. -
Page 8: Step Two - Wall Mounting & Wiring
STEP TWO – WALL MOUNTING & WIRING 3. Electrical Connection Remove the backplate from the charger and mount the backplate to the wall In Australia only the TN network is used, as shown on the label on the back plate. Connect the cable through the bottom of the junction box ensure conduit is connected to the bottom of the power box conduit... -
Page 9: Step Three - Install The Charger
Please connect the ethernet cable to the WAN port this should connect automatically to the internet if there's no IT restrictions, ( if static IP address is required please refer to the Ocular Configuration manual) (See Ocular or local supplier for manual) - Page 10 This hot spot will have the following SSID: IOC – 2.4GHz - ****** The password for this Hotspot is: IOC12345 Step 2: Navigate to the web-interface of the Ocular Charger After being connected to the Hotspot, open Microsoft Edge or Google Choose the Wi-Fi SSID that you prefer, and then input the Wi-Fi Password Chrome and navigate to: 192.168.10.1:8900...
-
Page 11: Step Five - Verify The Installation
STEP FIVE – VERIFY THE INSTALLATION Verify the power cables are wired properly Close the upstream RCD to power on the charger unit, and you should see the LED lights sequentially illuminate blue. If the LED red light illuminates or flashes, refer to the Troubleshooting table on page 13. -
Page 12: Lcd Display Details
LCD SCREEN DISPLAY DETAILS Welcome Screen Scan the QR code or swipe the Connect the charging plug RFID card to start charging Suspended by EV Charging in process Suspended by EVSE... - Page 13 Remove the charging plug Automatic upgrade mode Software downloading and activated upgrading automatically Network upgrade mode Software update error Micro SD card upgrade mode...
- Page 14 Factory Reset Invalid Authorisation Service not available RFID Activated Reserved Mode Explanation of ICONS...
-
Page 15: Troubleshooting
If the situation persists, contact your installer for Technical Support. MAINTENANCE AND REPAIR Regularly inspect the Charger components for damage. If damage is found, contact Ocular Charging The Electric Vehicle Charger contains no user-serviceable components. If the unit is not operating correctly, contact your... - Page 16 OCULAR CHARGING AUSTRALIA Email: sales@ocularcharging.com.au Web: www.ocularcharging.com.au...
Need help?
Do you have a question about the IOCAH10-7S and is the answer not in the manual?
Questions and answers