Table of Contents
Advertisement
OPERATION PARAMETER
ONLINE UNITS NUMBER
OPERATE MODE
SV1 STATE
SV2 STATE
SV3 STATE
PUMP_I
ADDRESS
OPERATION PARAMETER
PUMP_O
PUMP_C
PUMP_S
PUMP_D
PIPE BACKUP HEATER
TANK BACKUP HEATER
ADDRESS
OPERATION PARAMETER
GAS BOILER
T1 LEAVING WATER TEMP.
WATER FLOW
HEAT PUMP CAPACTIY
POWER CONSUM
Ta ROOM TEMP.
ADDRESS
OPERATION PARAMETER
T5 WATER TANK TEMP.
Tw2 CIRCUIT2 WATER TEMP. 35°C
TIS' C1 CLI. CURVE TEMP.
TIS2' C2 CLI. CURVE TEMP.
TW_O PLATE W-OUTLET TEMP. 35°C
TW_I PLATE W-INLET TEMP.
ADDRESS
OPERATION PARAMETER
Tbt1 BUFFERTANK_UP TEMP. 35°C
Tbt2 BUFFERTANK_LOW TEMP. 35°C
Tsolar
25°C
IDU SOFTWARE
01-09-2019V01
ADDRESS
OPERATION PARAMETER
ODU MODEL
COMP.CURRENT
COMP.FREQENCY
COMP.RUN TIME
COMP.TOTAL RUN TIME
EXPANSION VALVE
ADDRESS
#00
1
COOL
ON
OFF
OFF
ON
1/9
#00
OFF
OFF
OFF
OFF
OFF
ON
2/9
#00
OFF
35°C
1.72m
/h
3
11.52kW
1000kWh
25°C
3/9
#00
53°C
35°C
35°C
30°C
4/9
#00
5/9
#00
6kW
12A
24Hz
54 MIN
1000Hrs
200P
6/9
20
OPERATION PARAMETER
FAN SPEED
IDU TARGET FREQUENCY
FREQUENCY LIMITED TYPE
SUPPLY VOLTAGE
DC GENERATRIX VOLTAGE
DC GENERATRIX CURRENT
ADDRESS
OPERATION PARAMETER
TW_O PLATE W-OUTLET TEMP. 35°C
TW_I PLATE W-INLET TEMP.
T2 PLATE F-OUT TEMP.
T2B PLATE F-IN TEMP.
Th COMP. SUCTION TEMP.
Tp COMP. DISCHARGE TEMP.
ADDRESS
OPERATION PARAMETER
T3 OUTDOOR EXCHARGE TEMP. 5°C
T4 OUTDOOR AIR TEMP.
TF MODULE TEMP.
P1 COMP. PRESSURE
ODU SOFTWARE
HMI SOFTWARE
ADDRESS
INFORMATION
The power consumption parameter is optional. If some parameter
is not be activated in the system, the parameter will show «--»
The heat pump capacity is for reference only, not used to judge
the ability of the unit. The accuracy of sensor is ±1℃. The flow
rates parameters are calculated according to the pump running
parameters,the deviation is different at different flow rates,the
maximum of deviation is 15%.The flow parameters are calculated
according to the electrical parameters of the pump operation.
The operating voltage is different and the deviation is different.
The display value is 0 when the voltage is less than 198V.
6.9 For Serviceman
6.9.1 About For Serviceman
FOR SERVICEMAN is used for installer and service
engineer to.
•
Set the function of equipment.
•
Set the parameters.
6.9.2 How To Go To For Serviceman
Go to ''MENU'' > ''FOR SERVICEMAN''. Press
FOR SERVICEMAN
Please input password:
2
ENTER
ADJUST
#00
600R/MIN
46Hz
5
230V
420V
18A
7/9
#00
30°C
35°C
35°C
5°C
75°C
8/9
#00
5°C
55°C
2300kPa
01-09-2018V01
01-09-2018V01
9/9
.
3 4
Advertisement
Table of Contents
