Subscribe to Our Youtube Channel
Related Manuals for CASE CONSTRUCTION CX26C
Summary of Contents for CASE CONSTRUCTION CX26C
- Page 1 CX26C Mini Excavator SERVICE MANUAL Part number 51422576 English January 2018 © 2018 CNH Industrial Italia S.p.A. All Rights Reserved.
- Page 2 SERVICE MANUAL CX26C Cab - Tier IV final engine CX26C Canopy - Tier IV final engine 51422576 22/01/2018...
- Page 3 Contents INTRODUCTION Engine..................10 [10.001] Engine and crankcase ............. 10.1 [10.101] Cylinder heads .
- Page 4 [35.357] Pilot system ..............35.10 [35.360] Hammer and rotating bucket hydraulic system .
- Page 5 Thanks very much for your reading, Want to get more information, Please click here, Then get the complete manual NOTE: If there is no response to click on the link above, please download the PDF document first, and then click on it. Have any questions please write to me: admin@servicemanualperfect.com...
- Page 6 [55.405] External lighting switches and relays ..........55.12 [55.408] Warning indicators, alarms, and instruments .
- Page 7 INTRODUCTION 51422576 22/01/2018...
-
Page 8: Table Of Contents
Contents INTRODUCTION Foreword - Important notice regarding equipment servicing ........3 Safety rules . -
Page 9: Foreword - Important Notice Regarding Equipment Servicing
Specifications, descriptions, and illustrative material herein are as accurate as known at time of publication but are subject to change without notice. In case of questions, refer to your CASE CONSTRUCTION Sales and Service Networks. 51422576 22/01/2018... -
Page 10: Safety Rules
INTRODUCTION Safety rules Personal safety This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible death or injury. Throughout this manual you will find the signal words DANGER, WARNING, and CAUTION followed by special in- structions. -
Page 11: Safety Rules - General Information
Service parts Install CASE CONSTRUCTION genuine service parts. When placing an order, check the parts catalog. It contains the CASE CONSTRUCTION genuine part numbers. Any breakdowns arising from the installation of non-genuine parts are not covered by the warranty. Lubricants (fuel, hydraulic oil) Use the oil from the specified company or specified in the operator's manual or service Manual. -
Page 12: Safety Rules - Personal Safety
INTRODUCTION Safety rules - Personal safety Preliminary warnings to maintenance operation WARNING Avoid injury! Shut off the engine, remove the key, and make sure all machine motion stops before you service the machine. Failure to comply could result in death or serious injury. W1128B WARNING Improper operation or service of this machine can result in an accident. - Page 13 INTRODUCTION WARNING Tip-over hazard! Only raise the track as little as necessary. Failure to comply could result in death or serious injury. W0276A Hydraulic system WARNING Burn hazard! Before performing any service on the hydraulic system, you must allow it to cool. Hydraulic fluid temperature should not exceed 40 °C (104 °F).
- Page 14 INTRODUCTION WARNING Burn hazard! Hot coolant can spray and scald if you remove the radiator or deaeration tank cap while the system is hot. To remove the cap: allow the system to cool, turn the cap to the first notch, and wait for all pressure to release.
-
Page 15: Safety Rules - Ecology And The Environment
INTRODUCTION Safety rules - Ecology and the environment Soil, air, and water quality is important for all industries and life in general. When legislation does not yet rule the treatment of some of the substances that advanced technology requires, sound judgment should govern the use and disposal of products of a chemical and petrochemical nature. -
Page 16: Torque - Standard Torque Settings
INTRODUCTION Torque - Standard torque settings BOLT AND NUT Use following table for unspecified torque. Coarse thread Bolt size Wrench 10 t M6 x 1.0 10 mm 8.34 – 12.26 N·m (6.15 – 9.04 lb ft) 11.12 – 17.08 N·m (8.20 – 12.60 lb ft) M8 x 1.25 13 mm 19.66 –... - Page 17 INTRODUCTION Wrench Torque Thread size (UNF) 1-3/16-12 36 mm 176.26 N·m (130.00 lb ft) 1-7/16-12 41 mm 206.08 N·m (152.00 lb ft) 50 mm 1-11/16-12 343.02 N·m (253.00 lb ft) Fitting Thread size Wrench Torque 19 mm 1/4" 39.18 N·m (28.90 lb ft) 3/8"...
-
Page 18: Torque - Special Torque Settings
INTRODUCTION Torque - Special torque settings Component Bolt size Wrench Tightening torque Code 88 – 113 N·m (65.10 – 83.18 lb ft) Travel motor M12 x 1.75 19 mm Sprocket M12 x 1.75 19 mm 88 – 113 N·m (65.10 – 83.18 lb ft) Idler wheel M8 x 1.25 13 mm... - Page 19 INTRODUCTION SMIL16MEX1225HB 51422576 22/01/2018...
- Page 20 INTRODUCTION SMIL16MEX1226HB 51422576 22/01/2018...
- Page 21 INTRODUCTION SMIL16MEX1227HB 51422576 22/01/2018...
- Page 22 INTRODUCTION SMIL16MEX1228FB A. Cab version B. Canopy version 51422576 22/01/2018...
Need help?
Do you have a question about the CX26C and is the answer not in the manual?
Questions and answers