Advertisement
Insert four 18650 Li-ion or four 18650 IMR batteries with the positive terminal pointing towards the correct direction, as illustrated in the diagram below. When using flat top 18650 batteries, ensure the flat top battery connector is placed on the positive terminal of the batteries.
It is of crucial importance to ensure IMR batteries are installed correctly as labelled. Installing these batteries backward poses significant risk of short-circuiting, which in turn leads to combustion or explosion.
FL1 STANDARD | TURBO | HIGH | MID | LOW | UItralow | Strobe | SOS | Beacon |
6000 LUMENS | 2300 LUMENS | 1000 LUMENS | 320 LUMENS | 2 LUMENS | 6000 LUMENS | 6000 LUMENS | 6000 LUMENS | |
*45 min | *2 h | 4h 30min | 11h 15min | 1000h | ||||
655m | 420m | 270m | 153m | 12m | ||||
107200cd | 44100cd | 18400 cd | 5900cd | 36 cd | ||||
1m(Impact Resistant) | ||||||||
IPX8, 2m (Waterproof AND Submersible) |
NOTE: The stated data has been measured in accordance with the international flashlight testing standards ANSI/NEMA FL1, using 4 x IMR18650 batteries (3.7V, 3100mAh) under laboratory conditions. The data may vary in real-world use due to different battery use or environmental conditions.
* The runtime for Turbo and High mode are the testing result before starting temperature regulation.
FL1 STANDARD | TURBO | HIGH | MID | LOW | UItralow | Strobe | SOS | Beacon |
4500 LUMENS | 2300 LUMENS | 1000 LUMENS | 320 LUMENS | 2 LUMENS | 4500 LUMENS | 4500 LUMENS | 4500 LUMENS | |
*1h | *2 h 15min | 5h | 14h 30min | 1000h | ||||
600m | 420m | 270m | 153m | 12m | ||||
90000cd | 44100cd | 18400 cd | 5900cd | 36cd | ||||
1m(Impact Resistant) | ||||||||
IPX8, 2m (Waterproof AND Submersible) |
NOTE: The stated data has been measured in accordance with the international flashlight testing standards ANSI/NEMA FL1, using 4 x Li-ion 18650 batteries (3.7V, 3400mAh) under laboratory conditions. The data may vary in real-world use due to different battery use or environmental conditions.
* The runtime for Turbo and High mode are the testing result before starting temperature regulation.
* The use of the 6000 lumens Turbo: All 18650 batteries must be capable for a discharge current of at least 8A each, or use the product with the NITECORE NBP68HD battery pack. It is recommended to use the product with NITECORE protected IMR 18650 3100mAh (For TM28).
LEDs | 4×Cree XHP35 HI |
Battery options | li-ion/IMR/NBP68HD battery pack |
Dimensions | Length: 5.59" Head diameter: 2.68" Head side-length: 2.24" Tail diameter: 1.97" |
Weight | 14.6oz (battery excluded) |
Materials | Aerospace grade aluminium alloy construction, HAIII hard anodising |
Accessories | Holster, adaptor, lanyard, O-ring, charging port cover, flat top battery connector |
Type | Dimensions | Nominal voltage | Compatibility | Rechargeable | Must not be used with CR123 or RCR123 batteries. |
NITECORE 18650 3100mAh (For TM28) | 18650 | 3.7V | Recommended | Yes | |
Li-ion | 18650 | 3.7V | Recommended | Yes | |
IMR | 18650 | 3.6V/3.7V | Yes | Yes | |
NBP68HD battery pack | Batt Pack | 3.7V | Recommended | Yes |
Note: This product uses a two-stage power switch, access to its various functions depends on the extent the switch is pressed.
Upon each battery installation, a battery selection prompt comes up on the OLED display, select the correct battery type by pressing the display switch and press the power switch to confirm:
If no action is taken for 10 seconds after battery installation, the OLED display will enter standby mode.
Correct battery type must be selected upon battery installation, setting battery type to IMR while using regular 18650 li-ion batteries may render the product inoperative when switching to turbo (when OLED shows 6000 lumens).
Solution: Reinstall batteries and select the correct battery type when prompted. To guarantee the best user experience, it is recommended to use NITECORE IMR18650 batteries.
With the light turned off, pressing the power switch partway or all the way down will turn the light on, press the switch all the way down again to turn the light off.
The TM28 comes with 2 modes:
With the light turned on, press the switch twice in quick succession to enter strobe, press the switch partway down repeatedly to cycle through Strobe-SOS-Beacon, press the switch all the way down to turn the light off.
This product has an onboard OLED display that provides real-time operating data:
When entering standby mode simultaneously press and hold the display switch and the on/off switch to enter into Demonstration mode. In Demonstration mode, the OLED screen will cycle through the TM28's various messages. Simply press any button to exit Demonstration mode.
With the light turned on, hold down the switch for 1 second to enter lockout mode, this is designed to prevent accidental activation. To unlock, hold down the switch for 1 second again. Batteries are expected to last for 12 months in lockout mode.
Note: When the product is expected to be left unattended for extensive period, it is advised to loosen the tail cap.
When the product is turned on, the built-in power indicator under the switch will blink to indicate remaining battery:
Note:
To initiate the charging process, connect the charging port to a power outlet with the adaptor provided:
Heat generated by the LEDs can be substantial, prolonged operation at "Turbo" level will significantly increase operating temperature. Therefore, it is not recommended to use "Turbo" for long period of time. The TM28 has temperature regulation, when operating temperature reaches 60°Celsius (max bearable temperature by human skin), the TM28 automatically lowers its output to prevent temperature from increasing.
Note: Do not submerge the product in water or any liquid when it has generated sufficient heat, doing so will cause pressure inequalities and significantly increase risk of water damages.
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the TM28 that isn't answered in the manual? Leave your question here.