CONTENT GENERAL INFORMATION ..................4 Functionality and Features of the 1000BASE-T1 Media Converter ....4 1.1.1 Features ......................4 1.1.2 General Information ..................5 1.1.3 LINKS ......................5 1.1.4 General operating and safety strategy of Technica Engineering’s Products 1.1.5 General design rules for the power supply of Technica Engineering’s products ........................
Figure 1-1: 1000BASE-T1 MediaConverter The Technica Engineering 1000Base-T1 MediaConverter converts the Standard 1000Base-T1 to the widely known 1000Base-T and vice versa. Data Transfer is full duplex in both directions. Additional to this it has option to convert 100Base-TX to 100Base-T1 and vice versa.
International Protection: IP 2 0 Operating Temperature: -40 to +80 °Celsius 1.1.3 LINKS The User can download the latest firmware and documentation for the 1000BASE-T1 MediaConverter here: https://technica-engineering.de/produkt/1000base-t1-mediaconverter/ 1.1.4 General operating and safety strategy of Technica Engineering’s Products Technica Engineering’s products are designed for operation in automotive systems and for supply voltages of nominal 12 V or 24 V.
General design rules for the power supply of Technica Engineering’s products The power supply circuit of Technica Engineering’s products are equipped with self- protection components. This automatic function protects the devices against excessive temperature and too high supply-voltage by switching the device off. This automatic switch-off function is independent of any software function.
Page 7
When integrating the modules in a vehicle or test set-up, the user must ensure appropriate ventilation or air convection. Technica Engineering products must not be considered as a safety element out of context when using safety-critical systems and must be included in the safety assessment when used. The development class in a safety system must be taken into account with standard QM referred to ISO26262.
2.1 Connectors On the label on top of the device you can see an overview about all HW-Interfaces of the 1000BASE-T1 MediaConverter. Figure 2-1: Label of 1000BASE-T1 MediaConverter with pinning information 2.1.1 nano-MQS Connector The pinning of the ECU connectors is listed on the label on top of the device as well.
Page 11
Function Function n.c. n.c. n.c. n.c. n.c. 100/1000 BaseT1 Positive n.c. n.c. n.c. 100/1000 BaseT1 Negative n.c. n.c. n.c. n.c. n.c. Battery +12 Volt Input n.c. n.c. Battery Ground Input Table 2—1: Pinning of black Nano MQS connector The Tyco Electronics (TE) nano Micro Quad Lock System (nano-MQS) is used. Name Picture Part Number...
The 1000BASE-T1 MediaConverter has two DIP-Switches for configuration (see HAPTER 2.2.2 Status LEDs The 1000BASE-T1 MediaConverter has two status LEDs at the frontside of the case for the 1000BASE-T1 Port. Upper LED: Green Color. It is lit if there is a linkup on the BASE-T1 port.
Page 13
Lower LED: Yellow Color. It is toggling if there is communication on the BASE-T1 port 1000 BASE-T1 MediaConverter User Manual...
3 CONFIGURATION OF THE DEVICE The 1000BASE-T1 Media converter is configured by 2 DIP Switches on the front of the device. DIP-Switch Status Description ON (up) 100/1000 BASE-T1 Port is set to Master OFF (down) 100/1000 BASE-T1 Port is set to Slave ON (up) The device is set to 1 Gbit Mode.
On one hand 1000BASE-T1 Media Converter HW 0.6 (TE- 1401). It works with a PHY A0 from Marvell (88Q2112) which is only compatible with PHY Z0, Z1 and A0 versions.
PHYs: Marvell PHY Z0 Marvell PHY Z1 Marvell PHY A0 Note: With 1000BASE-T1 transceivers from other vendors no link up will be possible. Because this PHY is not IEEE compliant 5.2 HW variant 0.7 with Marvell A2 PHY 5.2.1 And Marvell Script 1.10...
PHY is set to Legacy Mode. There is no need from the customer to make any configuration This will ensure, that the devices can work with new and existing 1000BASE-T1 devices Note: The response from a Marvell PHY to the request of legacy mode is working only if the script is at least 1.10 or higher.
6 1000BASE-T1 Filter The following 1000BASE-T1 Filter is used in the 1000BASE-T1 MediaConverter: The Pulse AE5002 is used. Figure 6-1: Used Filter in 1000BASE-T1 MediaConverter 1000 BASE-T1 MediaConverter User Manual...
7 ADDITIONAL INFORMATION The delay time is constant 2.0.us. of each byte. The 1000BASE-T1 MediaConverter_ is optimized for automotive use. The maximum cable length for 100/1000BASE-T1 segments is limited to 15 meters. 1000 BASE-T1 MediaConverter User Manual...
Figure 1-1: 1000BASE-T1 MediaConverter ..............4 Figure 1-2 Copy of RoHS Certificate of Conformity ............8 Figure 2-1: Label of 1000BASE-T1 MediaConverter with pinning information .... 10 Figure 6-1: Used Filter in 1000BASE-T1 MediaConverter ..........18 1000 BASE-T1 MediaConverter User Manual...
Page 21
July 2020 of Technica Engineering’s Products 1.1.5 Added information on General Design Rules for the Power Supply of Technica Engineering’s Products Warranty and Safety Information updated RoHS Certificate of Compliance added Declaration of conformity added 1000 BASE-T1 MediaConverter User Manual...
Page 22
10 CONTACT If you have any questions regarding this product, please feel free to contact us: Technica Engineering GmbH Leopoldstr. 236 80807 München Germany Technical support: support@technica-engineering.de General information: Info@technica-engineering.de Most current user manuals and product information: https://technica-engineering.de/ 1000 BASE-T1 MediaConverter User Manual...
Page 23
EU declaration of conformity is available at the Čeština following internet address: https://technica- Tímto Technica Engineering GmbH prohlašuje, engineering.de/produkt/1000base-t1- že produkt 1000BASE-T1 MediaConverter (TE- mediaconverter/ 1401-1), je v souladu se směrnicí 2014/30/EU. Úplné znění EU prohlášení o shodě je k Español dispozici na této internetové adrese:...
Page 24
Internet: geraadpleegd op het volgende internetadres: https://technica- https://technica- engineering.de/produkt/1000base-t1- engineering.de/produkt/1000base-t1- mediaconverter/ mediaconverter/ Latviešu Polski Ar šo Technica Engineering GmbH deklarē, ka Technica Engineering GmbH niniejszym produkts 1000BASE-T1 MediaConverter (TE- oświadcza, że produkt 1000BASE-T1 1401-1), atbilst Direktīvai 2014/30/ES. Pilns MediaConverter (TE-1401-1), jest zgodny z ES atbilstības deklarācijas teksts ir pieejams...
Page 25
Slovensko Slovensky Technica Engineering GmbH potrjuje, da je Technica Engineering GmbH týmto vyhlasuje, izdelek 1000BASE-T1 MediaConverter (TE- že produkt 1000BASE-T1 MediaConverter (TE- 1401-1), skladen z irektivo 2014/30/EU. 1401-1), je v slade so smernicou 2014/30/EÚ. Celotno besedilo izjave EU o skladnosti je na Úplné...