This installation manual describes the installation of the possible. draws your attention to possible damage and/ or environ- Pendix eDrive on a bicycle. It is meant for bicycle mechan- mental hazards, the symbol Danger warns you against The Pendix eDrive motor is not designed for...
3.1 Residual risks 4. Scope of supply Observe compliance with the permissible total weight after installation of the Pendix eDrive in On the following page you will find a general overview of the components on the bike. the bicycle: Pos.-...
Frame material 6. Installation Pendix eDrive can be attached to all metal frames. If you wish to mount a Pendix system to a frame consisting of oth- er materials such as carbon, wood, etc. please consult our Please use the checklist (see section 10) and the online in- Pendix Service Department before installation.
• Chain guard, if available frame for the installation. The drilling of new If you want to use a gear hub with the Pendix eDrive, please • Crank on right (including chain wheel) holes can weaken the frame: it is a decision that make sure that the circuit for the torque of 65 Nm is acti- •...
Do not use grease when installing your Pendix eDrive into a frame made of fiber materials (car- bon frame)! Use standard carbon assembly paste instead. Magnetic fields destroy the electronic bottom Speed sensor of the 1st generation 2nd Generation Speed Sensor –...
Page 9
(No. 3). You can order this from bottom bracket on the left side to a torque of 65 Nm the Pendix online shop or via the ordering chan- and push in as far as it will go. +/- 3 Nm.
An alternative mounting option, if there are no screwed fix- Fix the accu strap with the upper battery holder ing points, is the Pendix clamp mount. It is not contained screw between the battery holder and the frame. in delivery scope of the standard set, but can be ordered at Pendix with Art.no.
The cables should have approximately 30 mm free length. It Pendix Montage Tipps does not matter which cable is on the left or right side. Pendix Installation Advice If this arrangement fits, the motor can be attached imme- diately by screwing it on.
Tighten the chain wheel screws to a torque of 9 Nm +/- 2 Nm. The chain wheels and pedals are not delivered with the Pendix system. In other words, you can use these parts of your bicycle if their dimensions agree with the details given in the chapter 5.2 „Requirements for installation“.
The disassembly of the Pendix eDrive takes place in reverse 8. First ride sequence of the described steps. Check the correct and safe function of the 32 Nm +/- 2 Nm gearshift before the first ride. The chain wheels After completing installation and switching on the Pendix...
Hints Please use the original installation manual for mounting the Pendix eDrive. In this mounting extension you will find all information you need to mount the Pendix eDrive on a folding bike. To 7.3 Battery holder Please use the Pendix clamp mount for installing the battery Pendix eDrive folding bike version holder to the bike.
Before installation: inspection of safety-relevant components on the bicycle check If there are former damages on safety-relevant components identifiable that do not allow a safe operation, please desist from installing the Pendix eDrive as long as the deficiency on the affected components is not remedied. check...
Page 16
bottom bracket mounted with correct torque → right: 15 Nm ± 2 Nm and left: 65 Nm ± 3 Nm bottom bracket turns free without increased resistance battery holder mounted with correct torque → 4,5 Nm ± 0,5 Nm square shaft left and right on bottom bracket greased electric motor mounted with correct torque →...
10.1 Comments 11. Guarantee conditions Warranty regulations can be found at tac.pendix.com The guarantee regulation can be found at: • Austria: https://pendix.at/garantie • Switzerland: https://pendix.ch/garantie • Belgium: https://pendix.be/garantie or https://pendix.be/en/warranty • Netherlands: https://pendix.nl/garantie or https://pendix.nl/en/warranty • all other countries: https://pendix.com/warranty...
Description and identification of the machine: Christian Hennig Function: Electric bicycle support motor (up to 25 km/ h or 15 ½ mph) (see Manufacturer’s address) Type/model: Pendix eDrive Place / date: Serial number: Construction year: Zwickau, the 18th of November 2021 legally responsible person, details: We herewith agree conformity with other guidelines/directives also applying to the product: •...
Page 21
Only to be observed by commercial installers...
16. Installation documentation by the installation company At the moment of the installation of the Pendix eDrive, you tick off installation checklist, handover documentation, make are going to be a manufacturer of a machine according to make a copy for your own files a copy for your own files the machinery directive.
Name: Function: Pedelec up to 25 km/ h Serial number: Address: Type/model: Pedelec with Pendix eDrive Construction year: Postcode, city: We herewith agree conformity with other guidelines/directives also applying to the product: RED Directive on the making available on the market of radio equipment (2014/53/EU),...