Page 1
System instruction Pendix eDrive IN / INs Compatible with Pendix.bike PRO App Valid only in combination with original bicycle operating instructions...
Pedelec unattended for ger to your life and/or health, if relevant instruc- The Pendix eDrive IN / INs is not designed or al- even a short time. tions are ignored or not correctly followed. It also lowed for use in explosion hazard areas.
Responsibility for possibly defective Pendix eDrive IN / INs may be performed. Do not electric drive unit of your Pendix eDrive IN / INs and how to ride a parts at purchase and all guarantee conditions take apart or open components! become invalid if the Pedelec/Pendix eDrive is Pedelec.
4. Example of product configurations Pendix eDrive IN(s) system Single motor system in two-wheeler Double motor system in tricycle/four-wheeler Motor(s) 1 wheel hub motor 2 wheel hub motors Nominal voltage 36 V / 48 V DC Power (max.) 700 W...
5. Overview components 5.1 Single motor system for single track vehicle Battery (battery type depending on manufacturer) Rotary handle/button To activate the start assist (on the frame or on the battery) Display of the system status Display of the support level Bluetooth-interface Bottom bracket bearing sensor Bottom bracket...
• If the battery is deformed in any way, the inte- The Pendix HMI is a unit that can be installed directly on the • Before undertaking a journey, the battery must be fully grated protective mechanism can be damaged.
Page 9
Do not use the charging unit in damp places or near leaking • Caution: magnetic fields around the battery plug/ When using the charging unit for the first few water. There is a risk of the charging unit overheating, catch- holder also influence medical equipment such as for times a smell may become perceptible.
The ePower (battery) is the power pack and central control noise is heard, and both whole points are positioned one unit of the Pendix eDrive IN / INs. The battery supplies the over the other. To remove the battery, please proceed in the necessary energy for the drive of the bicycle, at the same opposite sequence.
Page 11
If you want to know the charge level of the battery, simply Device ePower300 ePower 500 press the on/off button briefly when the battery is not con- parameters nected. You can see the charge level of the battery by the Cell technology Li-Ion (lithium-ion) colour of the LED indicator at the top of the battery:...
Page 12
The USB-C output can be activated or deactivated by press- which the LED display begins to show brightness levels in 5 In its lower section, the Pendix battery has been fitted with ing shortly the on-off switch button in case the battery is nei- steps.
5.5.2 AES Classic Charging the battery Device parameters Battery AES Classic Cell technology LiFePO4 Battery holder To charge the battery safely, read the safety in- Nominal voltage 36 V structions on page 9 of this manual. 669 Wh Capacity Release button (optionally 2-fold equipped) The battery must be removed from the holder for charging.
5.5.3 AES 2.0 Charging the battery Device Battery AES Battery AES parameters Battery holder 36 V 48 V To charge the battery safely, read the safety in- Cell technology LiFePO4 LiFePO4 structions on page 9 of this manual. Lock Nominal voltage 36 V 48 V The battery must be removed from the holder for charging.
5.5.4 AES Power Pack plus Charging the battery Device Battery AES Power Pack plus parameters Lock Cell technology LiFePO4 To charge the battery safely, read the safety in- structions on page 9 of this manual. Carrying Nominal voltage 48 V handle Capacity 1,440 Wh...
5.5.5 AES Super Pack Charging the battery Device Battery AES Super Pack parameters Lock Cell technology LiFePO4 To charge the battery safely, read the safety in- structions on page 9 of this manual. Carrying Nominal voltage 48 V handle Capacity 1,440 Wh The battery must be removed from the holder for charging.
5.5.6 BMZ Cargo Charging the battery Device Battery BMZ Cargo parameters To charge the battery safely, read the safety in- Cell technology Lithium-ion Battery holder structions on page 9 of this manual. Nominal voltage 48 V Capacity 807 Wh Release button The battery must be removed from the holder for charging.
On/Off button on the temperature that can be covered is reduced. HMI. With a Pendix ePower battery, the LED indicator lights Route influences such as underground, topogra- • Riding style: You can save energy with the optimum effective continuously in the colour of the current state of charge.
HMI is on permanently. This means that the motor is activated so that it can support you the moment you start The eDrive IN / INs can be equipped with a rotary handle or The reverse function is only activated for mul- pedalling.
The Bluetooth interface is located in the Pendix HMI. De- Should your Pendix eDrive IN / INs not function properly an- nect the Pendix eDrive with the app as it is described in the pending on the bicycle model, the HMI can be installed ymore, this can have different reasons.
10. Disposal Repairs on the motor may only be carried out by The built-in electronic bottom bracket is a me- a bicycle specialist/technician or a person with chanical wearing part. The durability is specified similar knowledge and technical background with 20,000 km, after which the bottom bracket The eMachine, rechargeable battery, measuring support, and with original replacement (spare) parts should be replaced.
Warranty regulations can be found at: tac.pendix.com The guarantee regulation can be found at: • Austria: https://pendix.at/garantie • Switzerland: https://pendix.ch/garantie • Belgium: https://pendix.be/garantie or https://pendix.be/en/warranty • Netherlands: https://pendix.nl/garantie or https://pendix.nl/en/warranty • all other countries: https://pendix.com/warranty 13. Imprint Responsible for content and illustrations Pendix GmbH Innere Schneeberger Straße 20...