Hatco Flav-R-Shield ED-20 Installation Manual

Flav-R-Shield™
Full Service Sneeze Guards
Model ED-20
Model ED-20 Full Service Sneeze Guards are available in ten
widths ranging from 36"–144" (914–3658 mm) with a common
height of 18" (457 mm). All of the widths can be configured in one
of three depths including 12", 15", or 18" (305, 381, 457 mm).
For additional information regarding Model ED-20 sneeze
guards, scan the QR Code below:
https://www.hatcocorp.com/en/equipment/sneeze-guard-equipment/
full-service/flav-r-shield-full-service-pass-over-sneeze-guard-ed20
Important Safety Information
To avoid serious injury and damage to equipment or property, read
the following safety information before installing this equipment.
Do not attempt to assemble and install sneeze guards alone.
Installation of sneeze guards requires two or more people,
dependent upon unit.
Always wear proper protective eye wear when handling glass
sneeze guards.
Never spray cleaners directly onto sneeze guard surfaces.
Spray cleaner into non-abrasive cloth, and then wipe down
surfaces.
Do not place anything on top of sneeze guard. It is not designed
to be a weight-bearing component.
Use non-abrasive cleaners and cloths only. Abrasive cleaners
and cloths could scratch finish of unit, marring its appearance
and making it susceptible to soil accumulation. Use of abrasive
materials will void warranty.
Assembly and Installation
1. Unpack all components. Verify that the appropriate number of
the items below are present.
• Face Panel, 3/8" Glass
• End Panel, 3/8" Glass
• Top Shelf, 3/8" Glass
• Post Assembly, 1" Stainless Steel
• Hardware Packet (includes hex wrench for set screws)
2. Remove the Mounting Flanges from each Post Assembly.
a. Slide the Flange Cover up and off of the flange.
b. Using the included hex wrench, loosen the set screw on the
flange.
c. Slide the flange off of the post assembly.
3. Install the Mounting Flanges to the mounting surface.
a. Refer to the chart and illustration below to determine the
location of the flanges.
b. Position the flanges in the appropriate locations, and mark
the screw hole locations. IMPORTANT! Measure carefully,
and make sure the flanges remain square to each other as
well as the installation location.
c. Pre-drill the screw holes in the mounting surface.
d. Install the flanges using the appropriate, countersunk-style
fasteners for the mounting surface.
© 2022 Hatco Corporation
INSTALLATION GUIDE
Width (A)
Item Number * (post center to center)
ED20-036xx
(914 mm)
ED20-048xx
(1219 mm)
ED20-060xx
(1524 mm)
ED20-072xx
(1829 mm)
ED20-084xx
(2134 mm)
ED20-096xx
(2438 mm)
ED20-108xx
(2743 mm)
ED20-120xx
(3048 mm)
ED20-132xx
(3353 mm)
ED20-144xx
(3658 mm)
* The "xx" at the end of the Item Numbers refers to the depth of the
sneeze guard. This will be "12", "15", or "18", depending on the
unit ordered.
† NSF Standards require the use of 18" End Panels for compliance.
4. Insert each Post Assembly into its corresponding Mounting
Flange. Make sure the posts are fully seated in the flanges.
5. Tighten the set screw on each Mounting Flange securely.
6. Slide each Flange Cover down onto its corresponding flange.
1
P/N 07.14.005.00-0622 [ED20_IG]
Depth (B) †
(post center to center)
36" 12", 15", or 18"
(305, 381, 457 mm)
48" 12", 15", or 18"
(305, 381, 457 mm)
60" 12", 15", or 18"
(305, 381, 457 mm)
72" 12", 15", or 18"
(305, 381, 457 mm)
84" 12", 15", or 18"
(305, 381, 457 mm)
96" 12", 15", or 18"
(305, 381, 457 mm)
108" 12", 15", or 18"
(305, 381, 457 mm)
120" 12", 15", or 18"
(305, 381, 457 mm)
132" 12", 15", or 18"
(305, 381, 457 mm)
144" 12", 15", or 18"
(305, 381, 457 mm)
A
18"
(457 mm)
B
continued...