Connect Tech JB0 User Manual

Multi-port serial communications adapters

Advertisement

Quick Links

Connect Tech Inc.
Industrial Strength Communications
Titan/cPCI
Multi-port Serial Communications
Adapters

User Manual

Connect Tech Inc
42 Arrow Road
Guelph, Ontario
N1K 1S6
Tel: 519-836-1291
Toll: 800-426-8979 (North America only)
Fax: 519-836-4878
Email: sales@connecttech.com
support@connecttech.com
FTP:
//ftp.connecttech.com
HTTP: //www.connecttech.com
CTIM-00009, Revision 0.00 September 24 2001
Part Number: MAN090
Titan/cPCI User's Manual, ver. 0.00

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the JB0 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Connect Tech JB0

  • Page 1: User Manual

    Connect Tech Inc. Industrial Strength Communications Titan/cPCI Multi-port Serial Communications Adapters User Manual Connect Tech Inc 42 Arrow Road Guelph, Ontario N1K 1S6 Tel: 519-836-1291 Toll: 800-426-8979 (North America only) Fax: 519-836-4878 Email: sales@connecttech.com support@connecttech.com FTP: //ftp.connecttech.com HTTP: //www.connecttech.com CTIM-00009, Revision 0.00 September 24 2001 Part Number: MAN090 Titan/cPCI User’s Manual, ver.
  • Page 2 This page is intentionally blank Titan/cPCI User’s Manual, ver. 0.00...
  • Page 3: Limited Warranty

    Limited Warranty Connect Tech Inc. warrants to the original purchaser of this Connect Tech hardware product that it is to be in good working order for a period of one year from the date of purchase from Connect Tech Inc. or an authorized Connect Tech dealer. Should this product, in Connect Tech Inc.'s opinion, fail to be in good...
  • Page 4: Trademark Acknowledgment

    Copyright/Trademark Copyright Notice The information contained in this document is subject to change without notice. Connect Tech shall not be liable for errors contained herein or for incidental consequential damages in connection with the furnishing, performance, or use of this material.
  • Page 5: Table Of Contents

    Contents Table of Contents Chapter 1: Introduction Introduction ...1-1 Manual Overview ...1-1 Conventions & Symbols ... 1-2 Product Overview...1-3 Titan/cPCI Adapters... 1-3 Features ... 1-3 Titan/cPCI Software... 1-5 Customer Service Overview...1-5 RMA Overview ...1-8 Chapter 2: Hardware Installation Introduction ...2-1 Configuration...2-1 Baud Rate Selection...
  • Page 6 Contents Chapter 4: Appendices (continued) Appendix D: RS-485/422 Line Interface ...4-9 Electrical Interface Selection ... 4-9 Full Duplex Mode ... 4-10 Half Duplex RS-485 ... 4-10 Multi-drop Slave Mode... 4-10 Line Termination ... 4-11 RS-485/422 Cable Wiring... 4-13 List of Tables Table 1: DB-9 cable connector pinouts ...4-5 Table 2: DB-37 cable connector pinouts ...4-6 List of Figures...
  • Page 7: Chapter 1: Introduction

    Product Overview - describes the Titan/cPCI, its features and specifications. Customer Services Overview - describes the various customer support services available to users of Connect Tech products. RMA Overview - describes the RMA policy and procedures for all Connect Tech products.
  • Page 8: Conventions & Symbols

    The "Warning" convention advises you to take certain precautions in order to avoid possible damage to your Connect Tech product. This message warns you that your Connect Tech product is very sensitive to static electricity. Make sure that before handling the product you practice proper ESD procedures.
  • Page 9: Product Overview

    Titan/cPCI adapters offer CompactPCI rear I/O capability. Please contact your Connect Tech Sales representative for further information concerning the available rear I/O options for your Titan/cPCI adapter. System requirements are one 3U CompactPCI compatible...
  • Page 10 Chapter 1: Introduction Figure 1 shows the locations of various hardware components found on Titan/cPCI adapters. Figure 1: Titan/cPCI adapters Line Termination/Bias Jumper blocks JC, JD Connector Port 2 Connector Port 1 Ejector Handle Jumper blocks JC, JD, JE, JF DB37 Connector Ejector...
  • Page 11: Figure 2: Titan/Cpci – 10 Port Configuration

    Chapter 3: Software Installation. Customer Service Overview If you experience difficulties after reading the manual and using the product, contact the Connect Tech reseller from which you purchased the product. In most cases the reseller can help you with product installation and difficulties.
  • Page 12 Chapter 1: Introduction Figure 3: Problem summary sheet Problem Description Connect Tech Product Description Product: Product serial no.: IRQ selected: I/O port address selected: Device driver: System Description Operating system: System type & manufacturer: Amount of RAM: Video adapter: Network adapter:...
  • Page 13 Chapter 1: Introduction We offer three ways for you to contact us: Mail/Courier You may contact us by letter and our mailing address for correspondence is: Connect Tech Inc. c/o Customer Service 42 Arrow Road Guelph, Ontario Canada N1K 1S6 Email/Internet You may contact us through the Internet.
  • Page 14: Rma Overview

    Note: Please pack the item for repair securely and ship it prepaid and insured. Connect Tech is not liable for damage or loss to the product due to shipping. Connect Tech will not accept items for repair without an RMA number.
  • Page 15: Chapter 2: Hardware Installation

    Reboot your system. If the BIOS cannot find a suitable configuration please contact Connect Tech Technical Support. Baud Rate Selection Titan/cPCI adapters offer ideal solutions for applications requiring serial communications up to 1.8432 Mbps.
  • Page 16: Rs-485/422 Line Interface

    Chapter 2: Hardware Installation RS-485/422 Line Interface The Titan/cPCI adapters come with a jumper selectable RS- 485/422 electrical line interface for each port. The RS-485/422 electrical interface is a reliable high-speed serial link that offers superior noise immunity and multi-drop network connectivity. The RS-485/422 electrical interface is also a superset of the RS- 422 electrical interface.
  • Page 17: Installing The Titan/Cpci Adapter In Your System

    Chapter 2: Hardware Installation Installing the Titan/cPCI Adapter in your System To install your Titan/cPCI adapter in your computer follow these steps: Your Titan/cPCI adapter is very sensitive to static electricity. Make sure you wear an anti-static wristband before you remove the card from the anti-static shipping bag.
  • Page 18 This page is intentionally blank Titan/cPCI User’s Manual, ver. 0.00...
  • Page 19: Chapter 3: Software Installation

    If you require further information please contact Connect Tech Customer Support. Before installing the Titan/cPCI software device driver, verify and note jumper settings described in Appendix D: RS-485/422 Line Interface for: Jumper block JA –...
  • Page 20 This page is intentionally blank Titan/cPCI User’s Manual, ver. 0.00...
  • Page 21: Chapter 4: Appendices

    Chapter 4: Appendices – Specifications Appendix A: Specifications Operating Environment Storage temperature: Operating temperature: 5° C to 70° C Relative humidity: 5 - 95% non-condensing Air movement: Altitude: Power Requirements Titan-2/cPCI: Titan-4/cPCI: CompactPCI Bus Interface One 3U cPCI slot Communications UARTs •...
  • Page 22: Dimensions

    Chapter 4: Appendices – Specifications Dimensions 3U cPCI compliant Connectors/Interface Titan-2/cPCI: Male DB-9 Titan-4/cPCI: Optional cable harness with DB-37 to four male DB-9 connectors Other connection options are available upon request. Contact Connect Tech for details. Titan/cPCI Part Numbers TN029000000 Titan-2/cPCI, 2 ports, RS232/485, front I/O, TN029100000 Titan-2/cPCI, 2 ports, RS232/485, TN049000000 Titan-4/cPCI, 4 ports, RS232/485, TN049000001 Titan-4/cPCI, 4 ports, RS232/485,...
  • Page 23: Certification

    Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. Connect Tech Inc. declares that the product(s) covered by the contents of this manual have been tested and found compliant with the below listed standards as required by the Electromagnetic Compatibility (EMC) Directive for General Immunity Compliance, EN 50 0082.1:1997...
  • Page 24 This page is intentionally blank Titan/cPCI User’s Manual, ver. 0.00...
  • Page 25: Chapter 4: Appendices - Connectors/Pinouts

    Chapter 4: Appendices – Connectors/Pinouts Appendix B: Connectors/Pinouts Appendix B outlines the connector pinouts for the Titan/cPCI-2 and the Titan/cPCI-4. Connector Pinouts Tables 1 and 2 outline the pinouts for the Titan/cPCI connectors or cable connectors. Technical Tip: Please ensure that you terminate signals if your application does not use them.
  • Page 26 Chapter 4: Appendices – Connectors/Pinouts Table 2: DB-37 cable connector pinouts Port Cable Part Number: CAB04DX Titan/cPCI User’s Manual, ver. 0.00 RS-232 RS-485/422 Signal Direction Signal signal gnd output TxD- output TxD+ input RxD- input RxD+ unused unused input RTS- input CTS+ output...
  • Page 27: Chapter 4: Appendices - Factory Settings

    Chapter 4: Appendices – Factory Settings Appendix C: Factory Settings Function Electrical Interface Jumper block JB is set for all ports RS- Half Duplex Termination Note: Please see Figure 1 for the locations of these jumper blocks. Factory Setting 485/422 - all positions not jumpered Jumper block JA is set for all ports running in full duplex or multi-drop slave mode - all positions not jumpered...
  • Page 28 This page is intentionally blank Titan/cPCI User’s Manual, ver. 0.00...
  • Page 29: Chapter 4: Appendices - Rs-485/422 Interface

    Figure 1 shows the location of jumper block JB. Technical Tip Please refer to the technical tips or release notes concerning installation and configuration of various device drivers and software utilities. If you require further information please contact Connect Tech Technical Support Example 1 Example 2 Technical Note: You can set up the RS-232 serial ports to run at up to 230.4...
  • Page 30: Full Duplex Mode

    4-10 Chapter 4: Appendices – RS-485/422 Interface Full Duplex Mode By not installing pins on jumper block JA and by using features in our driver software, you can run the individual RS-485/422 ports in full duplex mode. This mode is typically used in point to point RS-485/422 situations much like RS-232.
  • Page 31: Line Termination

    Chapter 4: Appendices – RS-485/422 Interface Line Termination You can use jumper blocks JC, JD, JE and JF to terminate and bias TxD ±, RxD ±, RTS ±, and CTS ± on the individual RS- 485/422 ports through jumper selectable 150 Ω fixed resistors. Please refer to Figure 4 for a partial schematic of the RS-485/422 circuit for the Titan/cPCI and to Figure 1 for the locations of JC, JD, JE and JF.
  • Page 32: Technical Notes

    4-12 Chapter 4: Appendices – RS-485/422 Interface Example The following example shows the settings on JC, JD, JE and JF where RS-485 port 1 is terminated on RTS ± and TxD ±, the RS-485 port 2 is set for bias/termination on RTS ±, TxD ±, CTS ±, and RxD ±, the RS-485 port 3 is not terminated, and port 4 is set for RS-232 on jumper block JB and therefore should not be terminated...
  • Page 33: Figure 5: Rs-485/422 Wiring Diagram (4 Wire)

    Chapter 4: Appendices – RS-485/422 Interface RS-485/422 Cable Wiring You can wire Titan/cPCI adapters in various ways to communicate with RS-485/422 peripherals. This section describes a few examples of RS-485/422 cabling schemes. Figure 5 describes a 4 wire cabling scheme between a port on the Titan/cPCI adapter to a port on the RS-485/422 peripheral.
  • Page 34: Figure 6: Rs-485/422 Wiring Diagram (2 Wire)

    4-14 Chapter 4: Appendices – RS-485/422 Interface Figure 6 describes a 2 wire cabling scheme between a port on the Titan/cPCI adapter to a port on the RS-485/422 peripheral. Figure 6: RS-485/422 wiring diagram (2 wire) Technical Tip The RS-485/422 electrical interface consists of a differential signaling scheme.
  • Page 35 Titan/cPCI User’s Manual, ver. 0.00...
  • Page 36 Titan/cPCI User’s Manual, ver. 0.00...

This manual is also suitable for:

Jb1Jb2Jb3Titan/cpci-2Titan/cpci-4

Table of Contents

Save PDF