Page 1
PLE385 Iiyama SERVICE MANUAL PLE385 Monitor THESE DOCUMENTS ARE FOR REPAIR SERVICE INFORMATION ONLY.EVERY REASONABLE EFFORT HAS BEEN MADE TO ENSURE THE ACCURACY OF THIS MANUAL; WE CANNOT GUARANTEE THE ACCURACY OFTHIS INFORMATION AFTER THE DATE OF PUBLICATION AND DISCLAIMS RELIABILITY FOR CHANGES, ERRORS OR OMISSIONS.
PLE385 Iiyama ENVIRONMENTAL ABSOLUTE MAXIMUM RATINGS Ta=25ºC ITEM STMBOL CONDITIONS MAX UNIT NOTE Ambient Storage ºC Note 1 temperature Operation No Condensation Humidity Ta=40ºC max – – Note 2 Vibration Storage Note 3 – – Shock Storage – – 11ms/direction [Note 1] Care should be taken so that the LCD module may not be subjected to the temperature beyond this specification.
PLE385 Iiyama 3. OPERATING INSTRUCTIONS 3.1 GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor. By changing these settings, the picture can be adjusted to your personal preferences.
Page 7
PLE385 Iiyama OSD TABLE: Contrast Adjust the picture contrast. Brightness Adjust the picture brightness. Focus Adjust picture Focus. Clock Adjust picture Clock. H-Position Adjust the horizontal position of the picture. V-Position Adjust the vertical position of the picture. Language Multi-Language selection Adjusts Red intensity.
PLE385 Iiyama The recovery from Off-state requires no manual power on. Mode H-Sync V-Sync. Video Pw-cons. Indicator Rec. time Power-On active < 35 w Green LED Power-off blanked < 3w Orange LED < 5s blanked < 3W Orange LED < 5s blanked <...
PLE385 Iiyama 4.4.2 OPTICAL CHARACTERISTICS The optical characteristics are measured under stable conditions at 25℃(Room Temperature): 4.4.3 Back-light Unit Page 11 of 50...
PLE385 Iiyama 5.2 SOFTWARE FLOW CHART Main( ) Disable All Interrupt Initialize Mascot chip and other Chips on application board such As Video chip Enable All Interrupt Mode changed Sync-Isr Interrupt Service routine If Sync Flag = 1 Sync Process...
Page 14
PLE385 Iiyama Auto Tune Tune H. Position Tune V. Position Tune Pitch Tune Phase Tune H. Position V. Position Return Page 14 of 50...
Page 15
Sync Process ( ) PLE385 Iiyama Vsync or Hsync overflow ? Display the message of “No signal” and “Go to sleep” Sync changed ready ? Enter Power saving Enable sync interrupt Sync out of range ? Exit power saving status...
PLE385 Iiyama MAINTAINBILITY 8.1 EQUIPMENTS AND TOOLS REQUIREMENTS 1、 Voltmeter. 2、 Oscilloscope. 3、 Pattern Generator. 4、 DDC Tool with a IBM Compatible Computer. 5、 Alignment Tool. 6、 LCD Color Analyzer. 7、 Service Manual. 8、 User Manual. Page 26 of 50...
PLE385 Iiyama 8.2 TROUBLE SHOOTING 8.2.1MAIN BOARD 1. NO SCREEN APPEAR Page 27 of 50...
Page 28
PLE385 Iiyama 2.PANEL-POWER CIRCUIT Check R98 should have response from 12V to 0V Check the PPWR panel power relative circuit, Q12.Q13 When we switch the power switch from on to off In normal operation, when LED =green, R98 should =12 v,...
Page 29
PLE385 Iiyama 4.U6-DATA OUTPUT Page 29 of 50...
PLE385 Iiyama 8.2.2 POWER/INVERTER BOARD (INPC5216A2D) 1) W / LED , No Backlight Check CON1 Pin1 =12V Check adapter or MB Check ON/OFF signal Check Interface board Check IC1 pin2=12V Change Q1 or Q2 Check U1 Pin1 have the output of square wave at short time Change U1 Check D1(-),D2(-) have the output of square wave at short time.
PLE385 Iiyama 8.2.3 KEYPAD BOARD OSD is unstable or not working Connect Key Pad Board Is Key Pad Board connecting normally ? Replace Button Switch Is Button Switch normally ? Replace Key Pad Board Is Key Pad board normally ?
B、MEM. CHANNEL 4(6500 color): 6500 color temp. parameter is x=313±20, y=329±20, Y=230±30 cd/m 3、Into factory mode of PLE385 A 、Press MENU button during 2 seconds along with press power button will activate the factory mode, then MCU will do AUTO LEVEL automatically. Meanwhile press MENU the OSD screen will located at LEFT TOP OF PANEL 4、Bias adjustment :...
PLE385 Iiyama B、Adjust C1(6500) color-temperature 1、Switch the chroma-7120 to RGB-Mode (with press “MODE” button ) 2、Switch the MEM. Channel to Channel 4( with up or down arrow on chroma-7120 ) 3、The LCD-indicator on chroma-7120 will show x = 313 ±20, y = 329 ±20, Y = 230 ±30 cd/m...
Page 37
PLE385 Iiyama W33L4477 D T TOP COVER 1.01 PCS W33L4478 D T BOTTOM COVER 1.01 PCS ----- ------------------------- ----------------------- --------- ----- PAREN T NO : ADPC12400BAI LCD ADAPTER ASS'Y FOR I ----- ------------------------- ----------------------- --------- ----- L901 6L 31502 1.5MM RIVET...