Advertisement
WARNING:
To avoid the risk of fire, explosion, or
electric shock, this product should be
installed, inspected, and maintained by
a qualified electrician in accordance
with all applicable electrical rules and
regulations.
Safety Instruction:
To avoid electric shock:
Be certain electrical power is OFF
before and during installation and
maintenance.
Make sure the supply voltage is the
same as the rated luminaire voltage.
The technical data indicated on the
LED luminaires are to be observed.
Changes
of
the
design
modifications to the LED luminaire are
not permitted.
Observe
the
national/regional
electrical safety rules and regulations
during installation.
The LEDs of this luminaire are not
replaceable; when the LEDs reach
their end of life, the whole luminaire
shall be replaced.
NOTE: Watertight fittings are required to be
used on this luminaire.
Equipment Application
This product can be used inside or outside to
illuminate areas in an industrial location.
WARNING: Please ensure the application
structure can handle the weight of the
luminaire. Dialight is not responsible for any
damages to the application structure or the
luminaire when mounted improperly.
Installation
Ensure that the mains voltage supply is
disconnected
before
connecting
luminaire.
Install
the
accordance
with
the
instructions as well as any other applicable
electric codes.
Always transport and store the equipment in
its original packaging and keep in a dry
location. When unpacking check for any
cracks or damage in the housing or lens. If in
doubt, do not install.
When assembling the cable entries for the
mains
connection,
always
manufacturer's specifications for the glands
used. Unused cable entries must be closed
and sealed by a certified blanking plug.
9100FLM000900 REV E
Page 3 of 10
ProSite Floodlight for UL 1598/1598A
Technical Data:
Locations:
F*U*****(D/J)*****
F*U*****S*****
Notice for UL 1598/1598A Models:
Outside Type (Salt Water)
Suitable for Wet Locations
Convient aux Emplacements Mouillés
Temperature Range:
F1U****(B/C/E/F)******
F2U****(F/H/L)******
F2U****(E/N)******
and
Rated Input Voltage:
F*U***(2/8)*******
120-277 VAC 50/60 Hz or 120-250 VDC
F*U***(5/9)*******
Weight:
F1U***********
F2U******(E/F)****
F2U7*****T****
F2U4*****T****
F2UN*****T****
Impact Rating:
F*U4**********
F*U7**********
F*UN**********
F*UNJ*********
Cable Entries:
Dimensions:
the
equipment
in
manufacturer's
NOTE: The addition of cable glands, dust
caps, electrical plugs, or occupancy sensors
may change the IP rating of this luminaire.
WARNING: Do not over tighten as the
protection rating may be compromised.
Always refer to the gland manufacturer's
data for torque settings.
Mounting the Luminaire
observe the
This product can be mounted via bracket or
slip fitter. All bracket and slip fit mounting
options offer 7.5 degrees of adjustment with
angle indication labels present. The mast arm
mounting
adjustment.
IP-66/67 & NEMA 4X
IP-66
-40°C to +65°C [-25°F to +149°F]
-40°C to +55°C [-25°F to +131°F]
347-480 VAC 50/60 Hz
29.9 lbs [13.6 kg]
54.1 lbs [24.5 kg]
57.7 lbs [26.2 kg]
55.1 lbs [24.9 kg]
50.7 lbs [22.9 kg]
IK-10
IK-08
IK-10
IK-07
2x 3/4 -14 NPT
(Not used on Slip Fitter models)
Mast Arm Models : 1x 3/4 NPS
See Technical Diagrams
option
offers
+/-
5
degree
Dialight, 1501 Route 34 South, Farmingdale, NJ, USA 07727
Tel: +1 732 919 3119 Fax: +1 732 751 5778
Bracket Models: F*U******(E/F)****
There are 2 bracket models, angled and
straight. See the Technical Diagrams section
for the mounting patterns.
Technical Data:
Power Consumption:
F1U***(2/8)B******
F1U***(2/8)C******
F1U***(2/8)E******
F1U***(2/8)F******
F2U***(2/8)F******
F2U***(2/8)H******
F2U***(2/8)L******
F2U***(2/8)N******
F1U***(5/9)B******
F1U***(5/9)C******
F1U***(5/9)E******
F1U***(5/9)F******
F2U***(5/9)F******
F2U***(5/9)H******
F2U***(5/9)L******
F2U***(5/9)N******
Once mounted, the angle of the luminaire
can be adjusted by loosening the M8 Hex Bolt
on each side of the bracket. When loosening,
do not back bolt out more than 5 full
rotations.
When the desired angle has been achieved,
the bolts can be tighten to lock in the angle.
Torque: 15 ft-lbs [20.3 N-m]
M8 Hex Bolts
WARNING: Do not loosen the Hex Nuts on the
bracket.
Hex Nuts
www.dialight.com
81 W
124 W
175 W
234 W
200 W
234 W
346 W
484 W
84 W
128 W
179 W
237 W
206 W
241 W
357 W
499 W
Advertisement
