Subscribe to Our Youtube Channel
Related Manuals for SteelFlex PLAC
Summary of Contents for SteelFlex PLAC
- Page 1 JOONG CHENN INDUSTRY CO., LTD. Sales Office: 3F28, No.5, Shin-Yi Rd., Sec. 5, Taipei, Taiwan 110 R.O.C. Tel: 886-2-27209980 Fax:886-2-27229750 www.steelflexfitness.com PLAC OWNER'S MANUAL...
- Page 2 PLAC ASSEMBLY INSTRUCTIONS HARDWARE ILLUSTRATION (A1)HEX BOLT 1/2"x3-1/4"L PARTIAL THREAD QTY.2 (A2)HEX BOLT 1/2"x5 1/4"L PARTIAL THREAD QTY.4 (A3)HEX BOLT 5/6"x1"L PARTIAL THREAD QTY.6 (A4)HEX BOLT 5/16"x3"L PARTIAL THREAD QTY.2 (A5)ROUND ALLEN HEAD M4X12L PARTIAL THREAD QTY.2 (A6)Co.Noid HEAD BOLT M10X25L PARTIAL THREAD QTY.2 inch 1"...
-
Page 3: Hardware Illustration
PLAC ASSEMBLY INSTRUCTIONS HARDWARE ILLUSTRATION (B1)NYLON LOCK NUT 1/2" QTY.6 (C1)1/2"(I.D.)FLAT WASHER Ø25 QTY.8 (B2)NYLON LOCK NUT M4 QTY.2 (C2)1/2"(I.D.)FLAT WASHER Ø34 QTY.6 (B3)NYLON LOCK NUT M12 QTY.2 (C3)5/16"(I.D.)FLAT WASHER Ø24 QTY.8 (C4)5/16" SPRING WASHER QTY.8 (C5)M4(I.D.)FLAT WASHER Ø12 QTY.2 inch 2"... - Page 4 PLAC ASSEMBLY INSTRUCTIONS HARDWARE ILLUSTRATION D1. Ø1" SHAFT COLLAR(8130-024)--------------------------------- [2PCS] D2. 1"X2" END CAP(9211-009)---------------------------------------- [2PCS] D3. 25x50 End Cap (9211-086)---------------------------------------- [1PCS] 45 End Cap (9211-091)------------------------------------------ [1PCS] D6. 2" Nylon Washer (9214-001)-------------------------------------- [4PCS] D7. 3" Nylon Washer (9214-008)-------------------------------------- [2PCS] D8. Ø90XØ50X10T RUBBER DOUNT(9310-016)---------------- [4PCS] D9.
- Page 5 PLAC ASSEMBLY INSTRUCTIONS PARTS ILLUSTRATION SHEET A[2PCS] B[1PCS] C[1PCS] D[1PCS] E[1PCS] F[2PCS] 6630-001 H[1PCS] G[1PCS] J[1PCS] I[2PCS] 9420-142 6640002-26 6640005-26 6650-001 Ø1"X2.5TX565L PLAC-082019 Page...
- Page 6 PLAC ASSEMBLY INSTRUCTIONS PARTS ILLUSTRATION SHEET K[1PCS] L[1PCS] M[4PCS] 6640006-26 8260-071 1"X2.5TX400L 6660-001A 6640-003 O[2PCS] Q[1PCS] 8343-163 9111-061 13.5 P[1PCS] U[1PCS] R[1PCS] 8360-200 9131-018 9121-058 S[1PCS] T[2PCS] 9161-051 9161-052 PLAC-032018 Page...
- Page 7 When assembling D, please follow the order. Stick the M though the hole on the right side of the main frame. After D has been fixed on right hand side, follow the same step to tighten the other side of D with M. Page PLAC-012018...
- Page 8 B1x2 C2x2 part 1 assembled turn over C2x2 Above shows STEP 2 assembled and completed A1x2 part 2 assembled homing M12X15L ROUND BOLT X2 1/2" WASHER Ø25 1/2"X3/4"L ROUND BOLT 1/2" WASHER Ø25 1/2"X3/4"L ROUND BOLT Page PLAC-082019...
- Page 9 M10 SPRING WASHER 3/8" WASHER Ø27 3/8" NYLON LOCK NUT(7t) 1/2" WASHER Ø34 6640-003 1/2"X3/4"L HEX BOLT 1/2"x1 1/4"L HEX BOLT M10 SPRING WASHER STEP: 1→2→3→4→1→2 M10X35L HEX BOLT(#2) STEP: #1→#2 tighten all screws as Figure 2 #2→#1 Page PLAC-032018...
- Page 10 Above shows STEP 4 assembled and completed C3x4 C4x4 A3x4 *:NEED TO LOOSEH BOTH ALLEN HEAD BOLT IN ORDER TO REMOVE SHAFT Page PLAC-012018...
- Page 11 Figure A B3x2 C2x2 Above shows STEP 5 assembled and completed M5X12L ROUND BOLT D8x2 Figure A WC-XXX Back Front Page PLAC-012018...
- Page 12 M10 WASHER Ø27 M10X30L ROUND BOLT Above shows STEP 6 assembled and completed C3X2 C4X2 A3X2 D11x2 D12x2 M10 WASHER Ø27 M10X30L ROUND BOLT C3x2 C4x2 A4x2 D12x2 *:NEED TO LOOSEH BOTH ALLEN HEAD BOLT IN ORDER TO REMOVE SHAFT Page PLAC-012018...
Need help?
Do you have a question about the PLAC and is the answer not in the manual?
Questions and answers