Panasonic AK-HRP931P Operating Instructions Manual page 11

Parts and their functions
+CLP: Detail edge overshoot clip
This is used to limit the length of the overshoot parts of the
detail edge components.
–CLP: Detail edge undershoot clip
This is used to limit the length of the undershoot parts of
the detail edge components.
KNEE: Detail edge knee
This function applies the knee to the detail edge parts.
CRM: Chroma detail
This function boosts the detail in the high chroma
saturation.
CRSP: Chroma detail crisp
This is used to remove the very faint noise components
below the level set from the chroma detail components.
CRED: Chroma detail reduce
This is used to suppress the chroma detail edge.
SKIN_DTL: Skin tone detail
This is used to set the skin tone detail function to ON or
OFF.
SKIN_LVL: Skin tone detail level
This is used to set the chroma saturation of the parts
where the skin tone detail is applied.
ZEB: Skin tone area zebra
This is used to set whether or not to apply zebra to the
areas where coring is applied as the skin tones to the Y
signals in the PM output.
PHAS: Skin tone area phase
This is used to move the areas recognized as the skin
tones in the range of 153 to 93 along the Q axis on the
color vector display.
WIDTH: Skin tone area width
This is used to widen the areas recognized as the skin
tones in the range of 1 to 20 along the I axis on the color
vector display.
CRSP: Skin tone detail crisp
This is used to remove the very faint noise components
below the level set from the skin tone detail components.
> Matrix control switch [MATRIX CONTROL]
This is pressed to change the correction amounts for the
R-G, R-B, G-R, G-B, B-R and B-G chroma saturation.
R - G R - B
– 1 0 0
B - R B - G
0 0
M T X 1 2
C y _ B
G - R G - B
+ 1 + 1 0
G A I N P H A S E
0 0
MTX 12, GAIN, PHASE
These are used to select the following 12-axis matrix
adjustment items: G, G_Cy, Cy, Cy_B, B, B_Mg, Mg, Mg_R,
R, R_Ye, Ye and Ye_G.
GAIN
This is used to adjust the chroma saturation (gain) of the
items set using MTX 12 in the range of –127 to +127.
PHASE
This is used to adjust the phase of the items set using
MTX 12 in the range of –127 to +127.
? SYSTEM
H E A D O P T L E V E L
C C U O P T L E V E L
R E T 1 R E T 2
H D S D I 1 H D S D I 2 H D S D I 3 H D S D I 4
D C M D U C M D
S P S P
H B A R S B A R P A T H O
A R I B S M P T
S D I 4
P M
A N L G O _ S E L
S D R G B
H _ C O H F I N ( H D T V )
9 9 1 2 3
H _ C O H F I N ( S D T V )
9 9 1 2 3
S C C O S C F I N ( S D T V )
7 3 0
S H _ H S H _ V
0 9 0 H
V E R
HEAD, CCU OPT LEVEL:Camera, CCU light reception
strength level
These indicate the light reception strength margins of the
camera head and CCU.
RET1, RET2, RET3, RET4: Return video settings
These are used to set the input allocations of the return
signals.
DCMD: Down-conversion system selection
This is used to select the down-conversion system.
UCMD: Up-conversion system selection
This is used to select the up-conversion system.
πππππ
πππππ
R E T 3 R E T 4
D C L K U C L K
O N O N
S E T
O F F 7 . 5 %
M S E L M L I N K
M I X O N
S Y N C T Y P E
O N T R I
11