Download Print this page

Bausch Datacom DinBox GSM M4 Reference Manual

Hide thumbs Also See for DinBox GSM M4:

Advertisement

Quick Links

Reference Manual for
DinBox GSM M4
V1.0a
Bausch Datacom NV Tiensesteenweg 56
B-3360 Korbeek-Lo
Belgium
+32 16 461288

Advertisement

loading
Need help?

Need help?

Do you have a question about the DinBox GSM M4 and is the answer not in the manual?

Questions and answers

Summary of Contents for Bausch Datacom DinBox GSM M4

  • Page 1 Reference Manual for DinBox GSM M4 V1.0a Bausch Datacom NV Tiensesteenweg 56 B-3360 Korbeek-Lo Belgium +32 16 461288...
  • Page 2 ! CAUTION ! ELECTRIC SHOCK HAZARD IF COVER REMOVED SERVICE BY QUALIFIED PERSONEL ONLY Bausch Datacom nv DinBox GSM M4 V1.0a...
  • Page 3 3.3 Power supply 3.4 GSM Module 3.5 Ins and outs 3.5.1 Power 3.5.2 Serial Interfaces 3.5.3 Ethernet 3.5.4 Digital Input 3.5.5 Digital Output 3.5.6 SIM Card Reader 3.5.7 GSM Antenna LED Indicators Configuration & Setup Bausch Datacom nv DinBox GSM M4 V1.0a...
  • Page 4 Bausch Datacom nv DinBox GSM M4 V1.0a...
  • Page 5 Introduction This manual is the reference guide when setting up the "DinBox GSM M4" modem. This modem has an Ethernet, a RS-232 and a RS-485 interface, 1 digital output and 1 digital input. It has a built-in power supply and an integrated GSM, GPRS, 3G or 4G module.
  • Page 6 Bausch Datacom nv DinBox GSM M4 V1.0a...
  • Page 7: Block Diagram

    PPPos STM32 F4 – CORTEX M4 Power Supply The "DinBox GSM M4" has 5 different power supply options. Before connecting power please check carefully that the supplied voltage and the wire connection is correct. PS1 option AC isolated 85 – 264 Vac / 100 – 370 Vdc PS2 option DC isolated 18 –...
  • Page 8 - galvanic isolated (optomos ‘solid state’ relay) FRAM The "DinBox GSM M4" has one FRAM (ferro electric RAM) of 64 Kbit (8.192 x 8 bits). This non-volatile memory can/will be used to store the configuration, measured data and log information.
  • Page 9 • IP class : IP3x Housing The "DinBox GSM M4" is enclosed into a Bernic Series 1570 housing. This housing is 9 modules wide and has a DIN rail snap slot for easy DIN rail mounting.  dimensions 157 mm x 86 mm x 58 mm ...
  • Page 10 10x LED conductor 3 mm 62,5 62,5 40,5 605 - 2 pin 605 - 4 pin 605 - 4 pin 5mm pitch 5mm pitch 5mm pitch 12,3 shielded RJ-45 Ethernet with 2 LED's [17,3] Bausch Datacom nv DinBox GSM M4 V1.0a...
  • Page 11 Power Supply The "DinBox GSM M4" has 5 power options. Please verify carefully that your product has the correct power supply option BEFORE connecting the power voltage. PS1 option AC isolated 85 – 264 Vac / 100 – 370 Vdc ...
  • Page 12: Gsm Module

    GSM module The “DinBox GSM M4” has a built-in state-of-art Sierra Wireless quad band GSM/GPRS module. Currently [15/04/2016] two options are possible : HL6528 (2G/GPRS) or HL8548 (3G). HL6528 (2G/GPRS) features:  Class 4 (2 W) for GSM 850 and E-GSM 900 GSM Output Power ...
  • Page 13  SMS reading from SIM card or ME storage  SMS sorting  SMS concatenation  SMS Status Report  SMS replacement support  SMS storing rules (support of AT+CNMI, AT+CNMA) A SMA connection is provided for external antenna connection. Bausch Datacom nv DinBox GSM M4 V1.0a...
  • Page 14 Disconnect the mains power before connecting or disconnecting the power and/or DTE plugs ! Ins and Outs Before starting with the installation, take a moment to become more familiar with the possible connections to and from the "DinBox GSM M4". Antenna RS-232 DC Output...
  • Page 15 3.5.1 Power As mentioned before the "DinBox GSM M4" has 5 power options. Not all options are using the same internal electronic circuits, and they all have there specific component stuffing. To meet all possibilities the “DinBox GSM M4” has 2 power supply in- and outputs.
  • Page 16 Power for direct powered options 4 and 5 should be connected via terminals 27 and 28. 3.5.2 Serial Interfaces The “DinBox GSM M4” has 2 serial interfaces; one full RS-232 non isolated interface on a RJ-45 connector and one galvanic isolated 2/4-wire RS-485 interface on 5 screw terminals.
  • Page 17 Jumper JP3 (internally, located onto the PCB) is provided to close A = Y and B = Z to switch to 2-wire. No external wiring needed. It's possible to add a 120 ohm end-resistor between A & B with jumper JP4 (internally, located onto the PCB). No external resistor needed. Bausch Datacom nv DinBox GSM M4 V1.0a...
  • Page 18 3.5.3 Ethernet The "DinBox GSM M4" has one 10/100 Mbit/s Ethernet connection. This Ethernet interface supports Auto-Negotiation to automatically determine the best possible speed and duplex mode of operation. It also supports Auto-MDIX to allow using a direct connect LAN cable, or a cross-over patch cable.
  • Page 19 3.5.4 Digital input connection The "DinBox GSM M4" can monitor 1 digital input. This input is a passive input; a voltage between 9 and 25Vdc needs to be applied to create an active input. RS-485 Power Ethernet G Z B A Y This DI is galvanic isolated with an optocoupler and has an isolation test voltage of 5.300 Vrms.
  • Page 20 3.5.5 Digital output connection The "DinBox GSM M4" can control 1 digital output. Non inductive AC or DC loads can be switched on or off. RS-485 Power Ethernet G Z B A Y The connection is done via screw contacts. These terminals have a 5 mm pitch and the maximum conductor cross section of 2.5 mm...
  • Page 21 Ethernet 3.5.7 GSM antenna connection The "DinBox GSM M4" has a 50 ohm SMA connector to connect the GSM antenna. Keep the antenna cables as short as possible to prevent the loss of antenna gain. Always use the modem with a proper antenna connected.
  • Page 22: Led Indicators

    LED indicators There are 10 status LED's onto the front of the "DinBox GSM M4": OFF – no power applied to the modem ON – power applied Alive Toggles together with the watchdog of the modem OFF – configuration mode ON –...
  • Page 23 Configuration & Setup This chapter describes the configuration of the “DinBox GSM M4”. Bausch Datacom nv DinBox GSM M4 V1.0a...