Table of Contents
Advertisement
Quick Links
Printed Matter No. 9836 9624 01
Publication Date 2020-09-29
Valid from Serial No. A1420001
Valid to Serial No. A2729999
BCP BL-12-I06
(5.0-12.0 Nm)
Read all safety warnings and instructions
Failure to follow the safety warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference
BCP BL-12-I06
8431127330
WARNING
Battery-Powered Screwdriver
Product Instructions
Advertisement
Table of Contents
Related Manuals for Atlas Copco BCP BL-12-I06
Summary of Contents for Atlas Copco BCP BL-12-I06
- Page 1 BCP BL-12-I06 Printed Matter No. 9836 9624 01 Battery-Powered Screwdriver Publication Date 2020-09-29 Valid from Serial No. A1420001 Product Instructions Valid to Serial No. A2729999 BCP BL-12-I06 8431127330 (5.0-12.0 Nm) WARNING Read all safety warnings and instructions Failure to follow the safety warnings and instructions may result in electric shock, fire and/or serious injury.
-
Page 2: Table Of Contents
Standby behaviour (from serial no.A3482445) ........ 16 Service ........................ 17 Preventing ESD problems ................ 17 Maintenance instructions ................ 17 Service recommendations .............. 17 Service instructions ................ 17 Preventive maintenance .............. 17 Electric circuit diagram ................ 18 Troubleshooting.................... 19 Error codes ..................... 19 © Atlas Copco Industrial Technique AB - 9836 9624 01... - Page 3 Recycling ....................... 20 Recycling instruction.................. 20 Recycling information BCP ................ 20 © Atlas Copco Industrial Technique AB - 9836 9624 01...
-
Page 4: Product Information
■ Damage to parts that occurs as a result of inadequate maintenance or performed by parties other than Atlas Copco or their Certified Service Partners during the warranty period is not covered by the warranty. ■ To avoid damage or destruction of tool parts, service the tool according to the recommended mainte- nance schedules and follow the correct instructions. -
Page 5: Website
You can find information concerning our products, accessories, spare parts and published matters on our website. Safety Data Sheets MSDS/SDS The safety data sheets describes chemical products sold by Atlas Copco. For more information, consult the website: www.atlascopco.com Choose Products - Safety Data Sheets, and follow the instructions on the page. -
Page 6: Service Instructions
Plus, refer to the exploded views. Lubricate o-rings and threaded connections with grease before assembling. Make sure that all threaded connections on the tool are tightened correctly according to the specifications on the exploded views. © Atlas Copco Industrial Technique AB - 9836 9624 01... -
Page 7: Operation
Ordering No. Torque rate Nm / rev. Torque range Nm 4145 0958 80 0.5 – 0.5 4145 0958 81 1.5 – 3.0 4145 0958 82 3.0 – 6.0 4145 0958 83 6.0 – 9.0 © Atlas Copco Industrial Technique AB - 9836 9624 01... -
Page 8: Controlling The Torque
Test joints - Soft joints Controlling the torque Atlas Copco’s Torque Analyser, ACTA 4000, plus an correctly-sized in-line rotary transducer, such as IRTT, are suitable instruments for controlling the torque. © Atlas Copco Industrial Technique AB - 9836 9624 01... - Page 9 Operation Remark / Included Ref. No. Ordering No. Description in Service kit Torque testing read- (Type: ACTA 3000 / out instrument FOCUS 2000) See our main catalogue or separate leaflet © Atlas Copco Industrial Technique AB - 9836 9624 01...
-
Page 10: Adjusting The Torque
Put the key in the hole at the front part of the tool. Turn the key clockwise to increase the tightening torque. Finish the adjustment at a holding position, located each 1.5 turns of the key. © Atlas Copco Industrial Technique AB - 9836 9624 01... -
Page 11: Setting Tool Speed
The display light on the speed setting unit flashes when it is put in the charger. 1 Green LED: ■ The green LED flashes: The battery pack charges. ■ The green LED is steady lit: The battery is fully charged. 2 Red LED: © Atlas Copco Industrial Technique AB - 9836 9624 01... -
Page 12: Attaching And Removing The Battery Pack
Since a battery pack slowly discharge itself, keep the battery pack in the charging unit that provides a trickle charge. Operating the tool Make sure that the switch (CW/CCW) is in the clockwise position. Release the trigger to change the switch. © Atlas Copco Industrial Technique AB - 9836 9624 01... - Page 13 A click sound is heard, the LED is green and the motor is turned off. The LED on the tool notify the tightening status after each tightening. There is no notification if the tool is run in counterclockwise mode. © Atlas Copco Industrial Technique AB - 9836 9624 01...
-
Page 14: Rehit Protection
To enable the buzzer function, push and keep the trigger half way. After 10 seconds the LED flashes orange and the buzzer function is activated. To disable the buzzer function, repeat the same procedure. © Atlas Copco Industrial Technique AB - 9836 9624 01... -
Page 15: Led Indications
Battery energy is not sufficient, motor turned off. Battery power status A temperature above 50°C reduces the battery perfomance. Do not expose the battery to heat or sunshine. Low battery status © Atlas Copco Industrial Technique AB - 9836 9624 01... -
Page 16: Charging The Battery Pack
BCP BL-12-I06 Charging the battery pack Use only an Atlas Copco battery charger (see optional accessories). Refer to the separate instruc- tions delivered with the charger. Fully charge a new or a long time unused battery pack before using your battery tool. Full loading capacity of a battery pack is reached after 4-5 charges. -
Page 17: Service
In order to maximize battery life, do not leave the battery connected to the tool you do not use it for sev- eral days. The battery can discharge and go into “sleep mode” which will require a special wake-up charge procedure. For further information, see instructions for multicharger, 4211542485. © Atlas Copco Industrial Technique AB - 9836 9624 01... -
Page 18: Electric Circuit Diagram
Service BCP BL-12-I06 Electric circuit diagram © Atlas Copco Industrial Technique AB - 9836 9624 01... -
Page 19: Troubleshooting
Overcurrent on the power circuit. The hardware limit is reached. The tool does not start or stops correctly. If the fault still appears, the power stage is faulty, contact customer service © Atlas Copco Industrial Technique AB - 9836 9624 01... - Page 20 Plastic housing Plastics, other, PA Motor Electronic Window kit Electronic Plastic housing Plastics, other, PA Li-Ion battery Electronic Trigger Plastics, other, PA Circuit board Electronic Battery connector Plastics, other, PA © Atlas Copco Industrial Technique AB - 9836 9624 01...
- Page 24 Original instructions © Copyright 2020, Atlas Copco Industrial Technique AB. All rights reserved. Any unauthorized use or copying of the contents or part thereof is prohibited. Atlas Copco Industrial This applies in particular to trademarks, model denominations, part numbers Technique AB and drawings.