Page 1
‘ Model D5P/D10P Power Ditcher Operator’s and Parts Manual LANDOLL COMPANY, LLC 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM F-1154-2304...
Instructions for Ordering Parts ** Repair parts must be ordered through an Authorized Dealer ** DEALER INSTRUCTIONS FOR ORDERING PARTS FROM LANDOLL PARTS DISTRIBUTION CENTER Phone #: 800-423-4320 785-562-5381 Fax #: 888-527-3909 Order online: dealer.landoll.com IDENTIFICATION PLATE The Identification Plate, which list the model and serial number of the equipment. It is located on the right side of the frame.
Page 3
DANGER DO NOT operate or perform any maintenance tasks on this equipment until you have completed the following: 1. Receive proper training to operate this equipment safely. 2. Read and understand the operator’s manual. 3. Be thoroughly trained on inspection and repair procedures. Failure to comply with this warning may result in serious injury or possibly death.
Page 5
INDEX Table of Contents Introduction and Safety Information Introduction ............1-1 Safety .
Page 6
TABLE OF CONTENTS INDEX Table provided for general use. NOTES: F-1154-2304...
CHAPTER 5 / Shows the various assemblies, sub-assemblies, and systems. Refer to this chapter PARTS MANUAL when ordering Landoll replacement parts. Order parts from your Landoll dealer. WARRANTY The Warranty Registration form is included with the product documents. Fill it out and mail it within 15 days of purchase.
You will find various types of safety information on the The safety statements contained in this manual relate to following pages and on the machine signs (decals) the operation of the Model D5P/D10P Power Ditcher. attached to the vehicle. This section explains their •...
INDEX TABLE OF CONTENTS INTRODUCTION AND SAFETY INFORMATION Transporting Safety Maintenance Safety IMPORTANT DANGER It is the responsibility of the owner/operator to • Stop the tractor and disengage the PTO before comply with all state and local laws. making any adjustments. Keep all shields in •...
Page 10
TABLE OF CONTENTS INDEX INTRODUCTION AND SAFETY INFORMATION Table provided for general use. NOTES: F-1154-2304...
The Cutter Head has (4) heat treated high carbon steel blades with a cutting diameter adjustable from 18" to 20". The D5P/D10P Series Power Ditchers are connected to The D5P18A Power Ditcher is designed for use on the tractor PTO shaft by means of a shielded double tractors with 50 to 110 PTO horsepower and 540 RPM u-joint.
TABLE OF CONTENTS INDEX STANDARD SPECIFICATIONS General Torque Specifications (rev. 4/97) Torque Specified in Foot Pounds This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and cap-screws assembled without supplemental lubrication (as received condition).
INDEX TABLE OF CONTENTS STANDARD SPECIFICATIONS Hydraulic Fitting Torque Specifications Torque Specified in Foot Pounds - 37 JIC, ORS, & ORB (REV. 10/97) This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing.
Page 14
TABLE OF CONTENTS INDEX STANDARD SPECIFICATIONS Table provided for general use. NOTES: F-1154-2304...
Page 15
Chapter 3 INDEX TABLE OF CONTENTS Assembly Instructions Receiving the Power Assembly Instructions Ditcher 1. The D5P18A and D10P18A Series Power Ditcher is completely assembled at the factory, except for the Universal Drive Shaft which is wired to the “A” frame. IMPORTANT 2.
6. Cat. II or III Standard or Quick Coupler Hitch 7. Removable End Plates for Ease of Service 8. Adjustable Skid for Depth Control 9. Safety Collars on Input and Output Shafts 10. Chain Adjustment Figure 3-1: D5P/D10P Power Ditcher Figure 3-2: D5P/D10P Power Ditcher F-1154-2304...
Page 17
TABLE OF CONTENTS Operation and Maintenance Operation CAUTION The Landoll D5P/D10P Power Ditcher is a ditching 1. Avoid injury or fatal accidents. Read these machine for controlling field water drainage by improving safety precautions completely and carefully! water run-off conditions. The Power Ditcher can make...
Page 18
TABLE OF CONTENTS INDEX OPERATION AND MAINTENANCE WARNING CAUTION 1. Do not clean, adjust or service when the 1. Wear personal protective equipment (PPE) machine is in motion. such as, but not limited to, protection for eyes, lungs, ears, head, hands and feet when 2.
Forward speed and depth of cut should be matched to soil conditions. 5. When backing or turning, the Ditcher should be raised to clear the ground. The Ditcher should never be raised to maximum height with the PTO engaged. Figure 4-1: D5P/D10P Tractor Attachment...
Page 20
JOINT ANGLE WRONG! REAR JOINT ANGLE IS LESS THAN FRONT JOINT ANGLE. REAR JOINT ANGLE FRONT JOINT ANGLE CORRECT! FRONT AND REAR JOINT ANGLES ARE EQUAL WHEN POWER DITCHER IS IN CORRECT WORKING POSITION. Figure 4-2: D5P/D10P Attachment to Tractor F-1154-2304...
Page 21
INDEX TABLE OF CONTENTS OPERATION AND MAINTENANCE Lubrication 1. Proper lubrication of your machine is instrumental in obtaining optimum performance and extended life. Neglect leads to needless breakdowns and WARNING unnecessary expenses. 2. Check oil level at the check plug on the chain housing Do Not lubricate machine while machine is in when the Power Ditcher is in an upright position.
TABLE OF CONTENTS INDEX OPERATION AND MAINTENANCE Maintenance Chain Adjustment 1. The chain adjusting bolt is located on the right hand WARNING side of main frame. Tighten to “finger tight” in order to remove excess chain slack. Do not over tighten. Do not clean, adjust or service when machine is 2.
Page 23
INDEX TABLE OF CONTENTS OPERATION AND MAINTENANCE Table provided for general use. NOTES:...
Page 24
Chapter 5 TABLE OF CONTENTS INDEX Parts List Frame Assembly AFTER 1998 FRONT Figure 5-1: Frame Assembly F-1154-2304...
Page 25
BUSHING,BLACK,D5P/D10P (1-1/4" X 2) E10317 KLIK PIN - 1/4" (1/4 X 1-3/4) W933232 SPRING PIN, SLTD 5/16 X 2 E0911 PIN WLDMT ZINC PLATE D5P/D10P (HITCH PIN) E100673 SPACER,D5P/D10P (2 X 2-3/4) E100640 BUSHING, D4P/D5P/D10P (1-7/16 X 2-3/4) E100699 PLATE,DEFLECTOR,BLACK...
Page 26
TABLE OF CONTENTS INDEX PARTS LIST Chain Case Assembly 24,25 24,25 26,35 Figure 5-2: Chain Case Assembly F-1154-2304...
TABLE OF CONTENTS PARTS LIST Cutter Head Assembly Figure 5-4: Cutter Head Assembly Cutter Head Assembly ITEM PART NUMBER DESCRIPTION EPA74013 CUTTER HEAD ASSY,BLK,D5P/D10P E0938 CUTTER HEAD WELD 16 OD E10498 NUT HEX LOCK 1/2-20 E100662-D BLADE, 2HOLES, BLACK 1-654-010056-03 SCREW 1/2-20UNFX1-1/2...
Page 30
TABLE OF CONTENTS INDEX PARTS LIST Decals DANGER WARNING Landoll Company, LLC Marysville, Kansas www.landoll.com Operate only with 540 rpm PTO MODEL # All drive line shields must be kept in place. SERIAL # MADE IN USA 1-573-010006 017805 ITEM 4...
Page 31
RIGHT VIEW LEFT VIEW Figure 5-6: Decal Location Decals ITEM PART NUMBER DESCRIPTION 10036 FASTENER, SERIAL NO. PLATE (HARDWARE FOR ITEM 4) 017805 DECAL, WARNING (D5P) 017806 DECAL, WARNING (D10P) 366579 DECAL, DANGER 1-573-010006 PLATE, NAME 366578 DECAL, WARNING 141259...
Page 32
TABLE OF CONTENTS INDEX PARTS LIST Table provided for general use. NOTES: F-1154-2304...
Page 33
Chapter 12 TABLE OF CONTENTS Glossary For clarity this glossary of industry standard abbreviations and their definitions are provided. For additional information, see instruction on the inside front HHCS ....Hex Head Cap Screw cover or the last page of this manual.
Page 34
TABLE OF CONTENTS INDEX GLOSSARY RH ....... . Righthand RND ....... . . Round SER .
Page 35
Chapter 7 TABLE OF CONTENTS Index Numerics 1D69249 ....... 2-573-010198 ......017805 .
Page 36
TABLE OF CONTENTS INDEX INDEX E11359AGCO ......5-4 E11375AGCO ......5-4 E11376AGCO .
Page 37
INDEX TABLE OF CONTENTS INDEX Table provided for general use. NOTES:...
Page 38
Instructions for Ordering Parts ** Repair parts must be ordered through an Authorized Dealer ** DEALER INSTRUCTIONS FOR ORDERING PARTS FROM LANDOLL PARTS DISTRIBUTION CENTER Phone #: 800-423-4320 785-562-5381 Fax #: 888-527-3909 Order online: dealer.landoll.com IDENTIFICATION PLATE The Identification Plate, which list the model and serial number of the equipment. It is located on the right side of the frame.
Page 39
Document Control Revision Log: Date Form # Improvement(s): Description and Comments 03/2001 F-351-0301 Operator’s Manual 02/2002 F-353-0202 Parts Manual 04/2011 F-351-0411 Operator’s Manual 04/2011 F-353-0411 Parts Manual 04/2023 F-1154-2304 Revise Manual, Combined Operator’s and Parts Manual, New Template *Revised Format “Year/Month”...
Page 40
Equipment from Landoll Company, LLC is built to exacting standards ensured by ISO 9001 registration at all Landoll manufacturing facilities. Model D5P/D10P Operation’s and Parts Manual Re-Order Part Number F-1154 LANDOLL COMPANY, LLC 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM...