Troubleshooting (Basic) - Panasonic Toughbook CF-74CCB02BM Operating Instructions Manual

Troubleshooting (Basic)

Follow the instructions below when a problem has occurred. There is also an advanced troubleshooting guide in the
"Reference Manual". For a software problem, refer to the software's instruction manual. If the problem persists, contact
Panasonic Technical Support (
( Reference Manual "Troubleshooting (Advanced)").
Starting Up
Cannot start up.
The power indicator or bat-
tery indicator is not lit.
The power is turned on but
"Warming up the system (up
to 30 minutes)" appears.
Cannot turn on the computer.
The computer does not
resume from standby.
(The power indicator blinks
quickly in green.)
You have forgotten the
password.
"Remove disks or other
media. Press any key to
restart" or a similar mes-
sage appears.
Windows startup and opera-
tion is slow.
The date and time are incor-
rect.
[Executing Battery
Recalibration] screen
appears.
[Enter Password] does not
appear when resuming from
standby/hibernation.
page 30). You can also check the computer's status in the PC Information Viewer
Connect the AC adaptor.
Insert a fully charged battery.
Remove the battery pack and the AC adaptor, then connect them again.
If a device is connected to the ExpressCard slot or the USB port, disconnect the
device, or set [ExpressCard Slot], [USB Port] or [Legacy USB Support] to [Disable]
in the [Advanced] menu of the Setup Utility.
The computer is warming up before start up. Wait for the computer to start up (takes up
to 30 minutes). If, "Cannot warm up the system" is displayed, the computer failed to
warm up and does not start. In this case, turn off the computer, leave it in an environ-
ment of 5 °C {41 °F} or higher temperature for about an hour, and then turn on the power
again.
Leave it in an environment of 5 °C {41 °F} or higher temperature for about an hour, then
turn on the power again.
Supervisor Password or User Password: Contact Panasonic Technical Support (
30).
Administrator password:
• If you have a password reset disk, you can reset the administrator password. Set the
disk and enter any wrong password, then follow the on-screen instructions and set a
new password.
• If you do not have a password reset disk, reinstall (
and then set a new password.
A floppy disk is in the drive and it does not contain system startup information. Remove
the floppy disk and press any key.
This message may appear with some devices connected to the
USB port . Remove the device, or set [ExpressCard Slot], [USB Port] or [Legacy USB
Support] to [Disable] in the [Advanced] menu of the Setup Utility.
If the problem persists after removing the disk, it may be a hard disk failure. Contact
Panasonic Technical Support (
F9 in the Setup Utility (
Press
Utility settings (excluding the passwords) to the default values. Start the Setup Utility and
make the settings again. (Note that the processing speed depends on the application
software, so this procedure may not make Windows faster.)
If you installed a resident software after purchase, turn off the residence.
Disable Indexing Service in the following menu.
Click [start] - [Search] - [Change preferences] - [Without Indexing Service]
Make the correct settings. Click [start] - [Control Panel] - [Date, Time, Language, and
Regional Options] - [Date and Time].
If the problem persists, the internal clock battery may need to be replaced. Contact
Panasonic Technical Support (
When the computer is connected to LAN, check the date and time of the server.
The 2100 A.D. or later year will not be correctly recognized on this computer.
The Battery Recalibration was canceled before Windows was shut down last time. To
start up Windows, turn off the computer by the power button, and then turn on.
To display [Enter Password] at resuming, set the Windows password. The password you
have set in the Setup Utility is not requested at resuming.
A Click [start] - [Control Panel] - [User Accounts] and select the account, and set the
password.
B Click [start] - [Control Panel] - [Performance and Maintenance] - [Power Options] -
[Advanced] and add a check mark for [Prompt for password when computer resumes
from standby].
page 20) and set up Windows,
page 30).
page 22 "To start the Setup Utility") to return the Setup
page 30).
page
ExpressCard slot or the
23