Nitecore P20UV V2 - White And UV Dual Output Tactical Flashlight Manual

Features

• White + UV Dual Output Tactical Flashlight specially designed for patrol inspection, mine exploitation, forensic science as well as gemological appraisal, document examination and currency detection
• The white light utilizes a CREE XP-L2 V6 LED with a max output of 1,000 lumens
• The UV light utilizes 4 x UV LEDs (320mW, wavelength 365nm)
• Utilizes an OP reflector for a wide range flood beam
• Highly efficient constant current circuit provides a stable output for up to 46 hours
• Dual tail switches enable intuitive operations for tactical applications
• STROBE READY™ Technology to enable a quick access to STROBE Mode (Patent No.: ZL201320545349.4)
• 3 easily selectable user modes available
• The power indicator on the tail cap indicates the remaining battery power (Patent No. ZL201220057767.4)
• Anti-impact reverse polarity protection mechanism specially designed for shooting sports (Patent No. ZL201220677948.7)
• Stainless steel clip with titanium coating included
• Strike bezel uses high strength silicon nitride ceramics to enable excellent glass breaking performance
• Optical lenses with double-sided scratch resistant coating
• Constructed from aero grade aluminum alloy
• HA III military grade hard-anodized finish
• Waterproof and dustproof rating in accordance with IP68 (2 meters submersible)
• Impact resistant to 1 meter

Specifications

Length: 151.2mm (5.95")
Head Diameter: 31.8mm (1.25")
Tube Diameter: 25.4mm (1")
Tail Diameter: 26mm (1.02")
Weight: 133.5g (4.71oz)

Accessories

Tactical Holster NTH20, Clip, Lanyard, Spare O-ring, CR123 Battery Magazine

Battery Options

Technical Data

FL1 STANDARD			HIGH	MID		LOW	UV	STROBE
				(Mode 3)	(Mode 2)
			1,000 Lumens	330 Lumens	180 Lumens	60 Lumens	320mW	1,000 Lumens
			2h 30min	7h	16h	46h	27h	─
			164m	94m	69m	41m	─	─
			6,700cd	2,230cd	1,200cd	430cd	─	─
			1m (Impact Resistance)
			IP68, 2m (Waterproof and Submersible)

Note: The stated data is measured in accordance with the international flashlight testing standards ANSI/PLATO FL1-2019, using 1 x 18650 Li-ion battery (3,500mAh) under laboratory conditions. The data may vary in real world use due to different battery usage or environmental conditions.

Operating Instructions

Battery Installation

Insert the battery(s) as illustrated and screw to tighten the tail cap.
Note: After the battery insertion, the power indicator beside the tail switches will flash to indicate the remaining power. Please refer to the "Power Indication" section of this manual for more details.

Warnings:

1. Ensure the battery(s) is/are inserted with the positive end towards the head. The product will not work if the battery(s) is/are incorrectly inserted.
2. Please use the battery magazine when using 2 x CR123 batteries to avoid battery rattling and to ensure a stable contact.
3. 
   Possible dangerous radiation! Don't look into the light! May be dangerous for your eyes.
4. When the power level is low, please stop using the product and replace or recharge the battery to prevent damage to the battery.
5. When the product is kept in a backpack or left unused for prolonged time, please remove all batteries to prevent accidental activation or battery leakage.

Tactical Momentary Illumination

Half press and hold the Power Button to turn on the light momentarily. Release to turn it off.

On / Off

On: When the light is off, press the Power Button until a click sound is heard to turn it on.

Off: When the light is on, press the Power Button until a click sound is heard to turn it off.

User Mode Selection

The P20UV V2 provides 3 user modes for different users and situations.

• Tactical Mode (Mode 1):
  In this user mode, only the HIGH Level, UV and STROBE Mode are available. It will automatically access HIGH when reactivated. When the light is on, short press the Mode Button (STROBE READY™) to switch between HIGH and UV.
• Law Enforcement Mode (Mode 2):
  In this user mode, only 2 brightness levels (MID of 180 Lumens and HIGH), UV and STROBE Mode are available. It will automatically access HIGH when reactivated. When the light is on, short press the Mode Button (STROBE READY™) to cycle through the following modes: HIGH – UV – MID.
• Daily Mode (Mode 3, Default Setting):
  In this user mode, 3 brightness levels (LOW, MID of 330 Lumens and HIGH), UV and STROBE Mode are available. When the light is on, short press the Mode Button (STROBE READY™) to cycle through the following modes: LOW – MID – HIGH – UV. The P20UV V2 will memorize and reaccess the previous mode when reactivated.

Note: The P20UV V2 will automatically lower its output to avoid overheating and prolong the lifespan of the battery when accessing the HIGH Level for over 2.5 minutes.

DO NOT direct the UV light to the naked eyes or the skin.

To select a desired user mode

1. Ensure the light is turned off.
2. Loosen the tail cap.
3. Keep holding the Mode Button (STROBE READY™) on the tail cap while simultaneously tightening the tail cap.
4. Once the tail cap has been tightened, the LED will indicate a user mode selected by flashing once for Tactical Mode, flashing twice for Law Enforcement Mode and flashing three times for Daily Mode.
5. To cycle through all 3 user modes, please repeat the above procedures.

STROBE READY

• When the light is off in any user mode, press and hold the Mode Button (STROBE READY™) to access the STROBE Mode. Release to turn it off.
• When the light is on in any user mode, long press the Mode Button (STROBE READY™) to access the STROBE Mode. Short press the Mode Button (STROBE READY™) again to return to the previous mode.

Power Indication

When the battery is inserted, the power indicator located on the tail cap will flash to indicate the remaining power of the battery:

1. Flashing three times indicates that the power is above 50%.
2. Flashing twice indicates that the power is below 50%.
3. Flashing once indicates that the power is near depletion.

Note: As a precise power reading is required, please ensure the P20UV V2 is powered down for at least 20 seconds before tightening the tail cap for this function.

Changing Batteries

The batteries should be replaced when the output appears to be dim or the flashlight becomes unresponsive due to low power.

Maintenance

Every 6 months, threads should be wiped with a clean cloth followed by a thin coating of silicon-based lubricant.

Warranty Service

Any DOA / defective product can be exchanged for a replacement through a local distributor/dealer within 15 days of purchase. After that, all defective / malfunctioning NITECORE^® products can be repaired free of charge within 60 months from the date of purchase. Beyond 60 months, a limited warranty applies, covering the cost of labor and maintenance, but not the cost of accessories or replacement parts.

For the latest information on NITECORE^® products and services, please contact a local NITECORE^® distributor or send an email to service@ nitecore.com

※ Should any discrepancy occur between this manual and information specified on www.nitecore.com, Sysmax Innovations Co., Ltd. reserves the rights to interpret and amend the content of this document at any time without prior notice.

SYSMAX Innovations Co., Ltd.
TEL: +86-20-83862000
FAX: +86-20-83882723
E-mail: info@nitecore.com
Web: www.nitecore.com
Address: Rm 2601-06, Central
Tower, No.5 Xiancun Road,
Tianhe District, Guangzhou,
510623, Guangdong, China Made in China

Please find us on facebook: NITECORE Flashlight
Thanks for purchasing NITECORE!

Videos

Nitecore P20UV v2 Tactical Flashlight Review Video

Documents / Resources

References

• http://www.nitecore.com

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Nitecore P20UV V2 - White And UV Dual Output Tactical Flashlight Manual