1. Manuals
  2. Brands
  3. Traxxas Manuals
  4. Motorized Toy Car
  5. Slash 4X4 Brushless
  6. Owner's manual

Traxxas Slash 4X4 Brushless Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
MODEL 68154-4
owner
s manual
'

Advertisement

Table of Contents
loading

Related Manuals for Traxxas Slash 4X4 Brushless

Summary of Contents for Traxxas Slash 4X4 Brushless

  • Page 1 MODEL 68154-4 owner s manual ’...
  • Page 2 ANATOMY OF experienced RC enthusiast you will find it helpful and fast. THE SLASH 4X4 Traxxas Slash 4X4 Brushless hangs it out for an all new way to Be sure and read through the rest of the manual to learn BRUSHLESS challenge your driving skills.

  • Page 3: Before You Proceed

    Traxxas service needs. Maintenance and replacement identified by the icons below. Be sure to read them! To-Win, Slash 4X4, BL-2s, and parts may be purchased directly from Traxxas by phone or online ProGraphix are trademarks or An important warning about personal safety or avoiding at Traxxas.com.

  • Page 4: Safety Precautions

    SAFETY PRECAUTIONS All of us at Traxxas want you to safely enjoy your new model. Operate • Insulate the Wires: Always insulate exposed wiring with heat shrink your model sensibly and with care, and it will be exciting, safe, and tubing to prevent short circuits.
  • Page 5 • ONLY use a Traxxas iD charger to charge Traxxas iD batteries. identifying the battery type and specifications. ALWAYS use a ONLY use a Lithium Polymer (LiPo) balance charger with a Traxxas iD charger to charge Traxxas iD batteries.
  • Page 6 SAFETY PRECAUTIONS (continued from previous page) • While charging or discharging, ALWAYS place the battery (all • DO NOT disassemble, crush, short circuit, or expose the batteries to types of batteries) in a fire retardant/fire proof container and on flame or other source of ignition. Toxic materials could be released. a non-flammable surface such as concrete.

  • Page 7: Tools, Supplies, And Required Equipment

    1.5mm “L” wrench 4-way wrench model, but are a good idea to include in any RC toolbox: • Safety glasses • Traxxas Ultra Premium Tire Glue, part #6468 (CA glue) • Hobby knife • Side cutters and/or needle nose pliers...
  • Page 8 ANATOMY OF THE SLASH 4X4 BRUSHLESS Caster Block Battery Steering Block Half Shaft Hold-Down Rear Camber Link Traxxas High-Current Battery Compartment Front Connector Suspension Arm Spur Gear Motor Drive Shaft Front Shock Tower Rear Shock Tower Chassis Shock Steering Servo...

  • Page 9: Quick Start: Getting Up To Speed

    QUICK START: GETTING UP TO SPEED The following guide is an overview of the procedures for getting your model running. Look for the Quick Start logo on the bottom corners of Quick Start pages. The Quick Start Guide is not intended to replace the 1.
  • Page 10 TRAXXAS TQ 2.4GHz RADIO SYSTEM INTRODUCTION power more efficiently than mechanical speed controls so that Your model includes the TQ 2.4GHz transmitter. When powered the batteries run longer. An electronic speed control also has Applying the Decals on, the TQ 2.4GHz will automatically locate and lock onto an...
  • Page 11 TRAXXAS TQ 2.4GHz RADIO SYSTEM Resistance - In an electrical sense, resistance is a measure of how 2-channel radio system - The TQ radio system, consisting of an object resists or obstructs the flow of current through it. the receiver, the transmitter, and the servos. The system uses To prevent loss of radio range, When flow is constricted, energy is converted to heat and is lost.
  • Page 12 TRAXXAS TQ 2.4GHz RADIO SYSTEM Your model is equipped with the Traxxas TQ 2.4GHz transmitter. MODEL WIRING DIAGRAM BL-2s Wiring Diagram The transmitter has two channels: Channel one operates the Motor steering, and channel two operates the throttle. The receiver...
  • Page 13 Refer to the to avoid losing control. select. Traxxas recommends you choose a genuine Traxxas EZ-Peak iD Troubleshooting section on page 18 for more information on charger for safer charging and maximum battery life and performance.
  • Page 14 To reinstall the body: INSTALLING THE BODY 1. Position the body on the chassis. Align the front and rear of the Your Slash 4X4 Brushless includes an innovative latching system for Battery iD body with the bumpers. securing the body to the chassis (body clips are not required).
  • Page 15 Traxxas connector is engineered to extract all the power your and do not bend or cut the white screw next to the antenna tube.
  • Page 16 TRAXXAS TQ 2.4GHz RADIO SYSTEM RADIO SYSTEM CONTROLS • In order for the transmitter and receiver to bind to one another, Remember, always turn the the receiver in the model must be turned on within 20 seconds transmitter on first and off of turning on the transmitter.
  • Page 17 TRAXXAS TQ 2.4GHz RADIO SYSTEM Throttle reversing procedure: 6. When looking down at the Note: Throttle reversing is often times unnecessary on electric model, the front wheels Using Reverse: While driving, models, as issues with the throttle can usually be solved by...
  • Page 18 TRAXXAS TQ 2.4GHz RADIO SYSTEM Higher Speeds Require Greater Distance TQ 2.4GHz Binding Instructions The faster you drive your model, the more quickly it will near the For proper operation, the transmitter and receiver must be Failsafe limit of radio range. At top speeds, models can cover anywhere electronically ‘bound.’...

  • Page 19: Adjusting The Electronic Speed Control

    1. Turn the transmitter off. transmission on high-traction surfaces. 2. Hold both MENU and SET. 7. To turn the BL-2s off, press the EZ-Set button until the LED turns TRAXXAS • 19 3. Turn the transmitter on. off (.5 seconds).
  • Page 20 ADJUSTING THE ELECTRONIC SPEED CONTROL BL-2s Profile Selection 4. The LED will blink and then turn solid Patented Training Mode The speed control is factory set to Profile #1 (100% forward, brakes, and reverse). green (Low-Voltage Detection ACTIVE) or (Profile #3) reduces forward To disable reverse (Profile #2) or to allow 50% forward and 50% reverse (Profile #3), red (Low-Voltage Detection DISABLED).

  • Page 21: Driving Your Model

    • The Traxxas TQ 2.4GHz transmitter is not water resistant. Do not subject it to speed and with repetitive hard acceleration.
  • Page 22 DRIVING YOUR MODEL • Do not operate your model during a rain storm or other inclement After Running Your Vehicle in Wet Conditions 1. Drain the tires by spinning the tires at high speed to “sling” the weather where lightning may be present. water out.
  • Page 23 Label which wire is for which channel. 4. Apply a small bead of silicone grease (Traxxas part #1647) to the wire clamp. 5. Install the wire clamp and tighten the two 2.8x8mm cap screws securely.

  • Page 24: Adjusting Your Model

    ADJUSTING YOUR MODEL Once you become familiar with driving your model, you might need 1. Move the front shocks to position 3 on the suspension arms. to make adjustments for better driving performance. 2. Move the rear shocks to position 4 or 5 on the suspension arms. 3.
  • Page 25 ADJUSTING YOUR MODEL Gearing Compatibility Chart: Centering Your Servo Motors and Gearing The chart below shows If you have removed the servo horn from your model’s steering servo, One of the more significant advantages to your model’s recommended gear combination or the servo has been removed for service or cleaning, the servo must transmission is the extremely wide range of available gear ratios.
  • Page 26 TUNING THE SEALED GEAR DIFFERENTIALS Adjusting the Slipper Clutch The action of the Slash 4X4 Brushless’s front and rear gear The model is equipped with an adjustable slipper clutch, which is differentials can be tuned for different driving conditions and To achieve a good starting built into the large spur gear.
  • Page 27 ADJUSTING YOUR MODEL 5. Slide the tie bar off the truck. Rear Differential Removal 6. Remove the two 3x15mm button-head screws from the 3x15 BCS differential cover. Do not remove the two screws that secure the shock tower. 3x20 BCS 7.

  • Page 28: Maintaining Your Model

    5. Check the mounting of the receiver and servo(s) and overtightening. If the bottom of the shock is leaking, then it speed control. is time for a rebuild. The Traxxas rebuild kit for two shocks is 6. Check the tightness of the wheel nuts with a wrench. part #2362.
  • Page 29 Suspension and slipper clutch assembly removal Your Slash 4X4 Brushless was designed with ease of disassembly in mind. The entire front and rear suspension assemblies can be removed from the chassis fully intact with the removal of only a few screws. Refer to the exploded views included in the your model’s Service Support Guide for complete assembly diagrams.
  • Page 30 ’ 6250 TRAXXAS WAY, McKINNEY, TEXAS 75070 1-888-TRAXXAS 230907 68154-4-OM-EN-R00...

This manual is also suitable for:

68154-4Slash 4x4

Table of Contents