Oregon Scientific RM338P, RM338PU - PROJI Projection Clock Manual

INTRODUCTION

This device bundles precise time keeping, alarm and temperature monitoring features into a single tool you can use from the convenience of your home. Keep this manual handy as you use your new product. It contains practical step-by-step instructions, as well as technical specifications and warnings you should know.

PACKAGE CONTENTS

Main unit	Power adapter	AAA batteries for main unit x 2

OVERVIEW

TOP VIEW

1. + - Press to increase settings, or press and hold to increase rapidly in setting mode.
2. SNOOZE | LIGHT - Press to snooze an alarm or activate the backlight and projection. Press and hold until you hear a beep to activate the projection for 5 minutes.
3. - Press to toggle between current time, calendar or alarm 1/2 displays for 5 seconds. Press and hold to enter setting mode.
4. – - Press to decrease settings, press and hold to decrease settings rapidly.
5. Projection lens
6. - Press to turn on/off alarms, press and hold to enter alarm setting mode.

REAR VIEW

1. Battery compartment
2. RESET - Press to reset the unit to default.
3. / PROJECTION - Press to flip the projection content in 180°. Press and hold to toggle continuous projection on/off.
4. RCC – Press to turn on and search RCC signal. Press and hold to turn off.
5. Battery compartment cover

LCD SCREEN

1. Time display
2. Weekday display
3. Indoor temperature display

Symbol	Description
	Alarm 1 is on.
	Alarm 2 is on.
	RCC signal received
IN	Main unit low battery

GETTING STARTED

INSERT BATTERIES

1. Gently push the battery compartment cover downwards to remove it from the main unit.
2. Insert the batteries, matching the polarities (+/-).

NOTE Replace the batteries when displays , or when the display is dim.

DC POWER

Plug the power cable to the power jack and plug the power adapter into a suitable power outlet.

NOTE It is recommended to insert the battery as a backup power source.

CLOCK

CLOCK RECEPTION

This clock synchronizes automatically with a clock signal. Press RCC to turn on and search for the clock signal.

The main unit is able to receive RF clock data with different RCC signal:

Clock signal reception indicator:

Icons	Description
	Main unit is searching for clock signal strength
(flash)	Main unit is searching for clock signal
	No clock signal
	Strong RCC signal received
	Weak RCC signal received

NOTE It takes 2-10 minutes to receive the clock signal. If the signal is weak, it could take up to 24 hours to receive a valid signal.

SET THE CLOCK MANUALLY

1. Press and hold . The screen displays ZONE and the number flashes.
2. Press once or press and hold +/- to adjust the setting. For EU/UK, the time-zone offset sets the clock up to +/- 23 hours from the received clock signal time.
3. Press to confirm.
4. Press once or press and hold +/- to adjust the setting for 12/24h hour format, hour, minute, year, calendar format (month-day/day-month), month, date, temperature unit (°C/°F) and language.
5. Press to confirm each setting.

NOTE

• The language options are English (ENG), Spanish (SPA), Italian (ITA), French (FRE) and German (GER).
• The signal reception is on after each reset or battery replacement.
• While in the setting mode, press and hold to save the settings and leave the setting mode.

ALARM

SETTING/ADJUSTING ALARM TIME

1. Press and hold .
2. Press once or press and hold +/- to adjust the hour and minute setting, then press to confirm.
3. Press +/- to toggle the weekday alarm ON/OFF, then press to confirm.
   • The alarm rings only on weekdays when the setting is ON.
4. Repeat step 2 – 4 for alarm 2 setting.

TURN ON/OFF ALARMS

Press to turn on/off the alarm in sequence:
Alarm1 > Alarm 2 > Both ON > Both OFF.

OPERATION

When the alarm rings, the backlight will flash. You may:

• Press to stop. The alarm will ring again on the next day.
• Press SNOOZE | LIGHT to snooze. The alarm rings again after 8 minutes.

PROJECTION

The projector displays the time on your ceiling for easy viewing in a darkened room. For the optimal projection results, place the unit within 1.5 - 2 m (5 - 6.5 ft) from the ceiling or wall.

• Press SNOOZE | LIGHT to activate the backlight and projection for 5 seconds.
• Press and hold SNOOZE | LIGHT until you hear a beep to activate the projection for 5 minutes.
• Press / PROJECTION to flip the projection content by 180°.
• Press and hold / PROJECTION to toggle the continuous projection on/off.

NOTE The continuous projection function is disabled when the main unit is not connected to the power adapter.

PRECAUTIONS

• Do not subject the unit to excessive force, shock, dust, temperature or humidity.
• Do not immerse the unit in water. If you spill liquid over it, dry it immediately with a soft, lint-free cloth.
• Do not clean the unit with abrasive or corrosive materials.
• Do not tamper with the unit's internal components. This invalidates the warranty.
• Only use fresh batteries. Do not mix new and old batteries.
• Images shown in this manual may differ from the actual display.
• When disposing of this product, ensure it is collected separately for special treatment.
• Placement of this product on certain types of wood may result in damage to its finish for which Oregon Scientific will not be responsible. Consult the furniture manufacturer's care instructions for information.
• The contents of this manual may not be reproduced without the permission of the manufacturer.
• Do not dispose old batteries as unsorted municipal waste. Collection of such waste separately for special treatment is necessary.
• Please note that some units are equipped with a battery safety strip. Remove the strip from the battery compartment before first use.

NOTE The technical specifications for this product and the contents of the user manual are subject to change without notice.

SPECIFICATIONS

MAIN UNIT

SUPPORT

Visit our website www.oregonscientific.com to learn more about Oregon Scientific products.

For any enquiry, please contact our Customer Services at info@oregonscientific.com.

Oregon Scientific Global Distribution Limited reserves the right to interpret and construe any contents, terms and provisions in this user manual and to amend it, at its sole discretion, at any time without prior notice. To the extent that there is any inconsistency between the English version and any other language versions, the English version shall prevail.

EU-DECLARATION OF CONFORMITY

Hereby, Oregon Scientific, declares that this PROJI Projection Clock (model: RM338P/RM338PU) is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A copy of the signed and dated Declaration of Conformity is available on request via our Oregon Scientific Customer Service.

Countries RTTE Approval Complied
All EU countries, Switzerland and Norway