Related Manuals for EZ Way Smart Lift L1000
Summary of Contents for EZ Way Smart Lift L1000
- Page 1 Service Manual Model L1000 Smart Lift ™ Form #1-147 WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov. Rev. 01/24/23...
-
Page 2: Table Of Contents
Table of Contents EZ Way, Inc. Parts Breakdown Maintenance Checklist Smart Lift Operating Instructions ™ Scale Calibration Advanced Smart Lift Features ™ Wiring Schematic Trouble-Shooting Guide EZ Way, Inc. • (800) 627-8940 • Fax (712) 542-1899 • www.ezlifts.com... -
Page 3: Parts Breakdown
L1000 Parts Diagram L1000 Parts List EZ Way, Inc. EZ Way, Inc. • (800) 627-8940 • Fax (712) 542-1899 • www.ezlifts.com Page 3 EZ Way, Inc. • (800) 627-8940 • Fax (712) 542-1899 • www.ezlifts.com... - Page 4 Hanger Assembly with Scale S-Beam 1000 lb. 17009 Hanger Assembly without Scale 1000 lb. 15500 Pad Green Hanger Assembly Lift 12020 Sling Hanger Assembly, 1000 lb. 12168 Electronic Actuator 12706 Hand Control Assembly EZ Way, Inc. • (800) 627-8940 • Fax (712) 542-1899 • www.ezlifts.com...
-
Page 5: Maintenance Checklist
4. Check the point where sling hanger and hanger spreader bar meet. If excessively worn, replace the bushings immediately. The hanger spreader and sling hanger wear points need to be checked for wear. If hooks appear worn, call EZ Way for instructions. BADLY WORN... - Page 6 With the test load applied to the lift, check all structural welds for any signs of stress or fatigue cracks. If any unusual noises or cracks are found, stop using the lift and call the EZ Way Service Department immediately! ☐...
-
Page 7: Smart Lift ™ Operating Instructions
1. After power up sequence, press and hold the Down key followed quickly by the Up key and hold both keys for 5 seconds. 2. Back out of Customer Settings by hitting left toggle switch. EZ Way, Inc. • (800) 627-8940 • Fax (712) 542-1899 • www.ezlifts.com... -
Page 8: Scale Calibration
9. When the display leaves this menu selection, it will have been calibrated to the selected weight. Exit the calibration menu. 10. Press “WEIGHT” key to verify calibrated weight to 1% accuracy. Calibration is now complete. EZ Way, Inc. • (800) 627-8940 • Fax (712) 542-1899 • www.ezlifts.com... -
Page 9: Advanced Smart Lift ™ Features
3. To override a ‘Weight Overload’, press the down key. The arm will only operate in the down direction during a Weight Overload. Note: This feature is only available on scale units. EZ Way, Inc. • (800) 627-8940 • Fax (712) 542-1899 • www.ezlifts.com... - Page 10 The purpose of the inspection reminder is to notify the customer that the lift or stand needs to be inspected with the ‘EZ Way Safety & Maintenance Checklist’ form (see attached). When the checklist is complete the reminder is to be reset in the Customer Settings Menu as described below.
- Page 11 1.3 and changes are made to the original code the next revision of code will display version 1.4. New controls with version 1.8 will have software updates included. EZ Way, Inc. • (800) 627-8940 • Fax (712) 542-1899 • www.ezlifts.com...
-
Page 12: Wiring Schematic
Smart Lift Wiring Schematic ™ EZ Way, Inc. EZ Way, Inc. • (800) 627-8940 • Fax (712) 542-1899 • www.ezlifts.com... -
Page 13: Trouble-Shooting Guide
Make sure they are not loose. Call Service if voltage is not good and connection is good. Continuous up/down Unhook toggles and airlines from board. If problem still persists call EZ Way Service. EZ Way, Inc. • (800) 627-8940 • Fax (712) 542-1899 • www.ezlifts.com...
Need help?
Do you have a question about the Smart Lift L1000 and is the answer not in the manual?
Questions and answers