Table of Contents
Advertisement
SAFETY INSTRUCTIONS
INSTALLATION
The installation must comply with
relevant national regulations.
•
Remove all the packaging and the transit bolts
including rubber bush with plastic spacer.
•
Keep the transit bolts in a safe place. If the
appliance is to be moved in the future they must
be reattached to lock the drum to prevent an
internal damage.
•
Always take care when moving the appliance as
it is heavy. Always use safety gloves and
enclosed footwear.
•
Follow the installation instructions supplied with
the appliance.
•
Do not install or use a damaged appliance.
•
Do not install or use the appliance where the
temperature can be less than 0°C or where it is
exposed to the weather.
•
The floor area on which the appliance is to be
installed must be flat, stable, heat resistant and
clean.
•
Make sure that there is air circulation between
the appliance and the floor.
•
When the appliance is in its permanent position,
check if it is levelled correctly with the aid of a
spirit level. If it is not, adjust the feet accordingly.
•
Do not install the appliance directly above a
floor drain.
•
Do not spray water on the appliance and do not
expose it to excessive humidity.
•
Do not install the appliance where the appliance
door cannot be fully opened.
•
Do not put a closed container to collect
possible water leakage under the appliance.
Contact the Authorised Service Centre to
ensure which accessories can be used.
ELECTRICAL CONNECTION
WARNING! Risk of fire and electric
shock.
•
WARNING: This appliance is designed to be
installed / connected to a grounding connection
in the building.
•
Always use a correctly installed shockproof
socket.
•
Make sure that the parameters on the rating
plate are compatible with the electrical ratings
of the mains power supply.
•
Do not use multi-plug adapters and extension
cables.
4
•
Make sure not to cause damage to the mains
plug and to the mains cable. Should the mains
cable need to be replaced, this must be carried
out by our Authorised Service Centre.
•
Connect the mains plug to the mains socket
only at the end of the installation. Make sure that
there is access to the mains plug after the
installation.
•
Do not touch the mains cable or the mains plug
with wet hands.
•
Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
•
This appliance is fitted with a 13 A mains plug. If
it is necessary to change the mains plug fuse,
use only a 13 A ASTA (BS 1362) fuse (UK and
Ireland only).
WATER CONNECTION
•
The inlet water shall not exceed 25 °C.
•
Do not cause damage to the water hoses.
•
Before connection to new pipes, pipes not used
for a long time, where repair work has been
carried out or new devices fitted (water meters,
etc.), let the water flow until it is clean and clear.
•
Ensure that there are no visible water leaks
during and after the first use of the appliance.
•
Do not use an extension hose if the inlet hose is
too short. Contact the Authorised Service
Centre for the replacement of the inlet hose.
•
When unpacking the appliance, It is possible to
see water flowing from the drain hose. This is
due to the testing of the appliance with the use
of water in the factory.
•
You can extend the drain hose to maximum 400
cm. Contact the Authorised Service Centre for
the other drain hose and the extension.
•
Make sure that there is access to the tap after
the installation.
USE
WARNING! Risk of injury, electric
shock, fire, burns or damage to the
appliance.
•
Follow the safety instructions on the detergent
packaging.
•
Do not put flammable products or items that are
wet with flammable products in, near or on the
appliance.
•
Do not wash fabrics which are heavily soiled
with oil, grease or other greasy substances. It
can damage rubber parts of the washing
machine. Prewash such fabrics by hand before
loading them into the washing machine.
Advertisement
Table of Contents
