Table of Contents
Advertisement
Quick Links
www.ti.com
EVM User's Guide:
BQ25176MEVM Evaluation Module
This user's guide describes the characteristics, operation, and use of the BQ25176MEVM evaluation module
(EVM). This EVM is designed to help the user evaluate and test the various operating modes of the BQ25176M.
This user's guide includes setup instructions for the hardware and software, a schematic diagram, a bill of
materials (BOM), and PCB layout drawings for the evaluation module.
Throughout this user's guide, the abbreviations EVM, BQ25176MEVM, BMS069, and the term evaluation
module are synonymous with the BMS069 evaluation module, unless otherwise noted.
1
Introduction.............................................................................................................................................................................2
1.1 Printed Circuit Board Assembly.........................................................................................................................................
Descriptions..................................................................................................................................................................2
2 Test Summary.........................................................................................................................................................................
2.1 Equipment..........................................................................................................................................................................
2.2 Cautions.............................................................................................................................................................................
2.3 Test Instructions.................................................................................................................................................................
Layout......................................................................................................................................................................4
3.2 Schematic..........................................................................................................................................................................
Materials...................................................................................................................................................................8
History....................................................................................................................................................................11
Trademarks
All trademarks are the property of their respective owners.
Hot surface! Contact may cause burns. Do not touch!
Some components may reach high temperatures >55°C when the board is powered on. The user must
not touch the board at any point during operation or immediately after operating, as high temperatures
may be present.
SLUUCR6 - DECEMBER 2022
Submit Document Feedback
ABSTRACT
Table of Contents
Materials...................................................................................................................4
WARNING
Copyright © 2022 Texas Instruments Incorporated
Table of Contents
BQ25176MEVM Evaluation Module
2
3
3
3
3
7
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Texas Instruments BQ25176MEVM
Summary of Contents for Texas Instruments BQ25176MEVM
-
Page 1: Table Of Contents
BQ25176MEVM Evaluation Module ABSTRACT This user’s guide describes the characteristics, operation, and use of the BQ25176MEVM evaluation module (EVM). This EVM is designed to help the user evaluate and test the various operating modes of the BQ25176M. This user’s guide includes setup instructions for the hardware and software, a schematic diagram, a bill of materials (BOM), and PCB layout drawings for the evaluation module. -
Page 2: Introduction
1 Introduction The Texas Instruments BQ25176EVM is a Li-Ion, Li-Poly and LiFePO4 chemistry battery charger IC for single cell. Charging voltage can be adjusted using external resistors on VSET. Charging current can be set from 60mA to 600mA with external resistor on ISET. -
Page 3: Test Summary
Note: IN, ON, Fixed are positions of a 3 pin header. If it is a 2 pin header then it is installed or not installed. SLUUCR6 – DECEMBER 2022 BQ25176MEVM Evaluation Module Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated... -
Page 4: Board Layout, Schematic, And Bill Of Materials
3 Board Layout, Schematic, and Bill of Materials 3.1 Board Layout The board layout is shown in Figure 3-1 Figure 3-7. Figure 3-1. Top Overlay Figure 3-2. Top Solder BQ25176MEVM Evaluation Module SLUUCR6 – DECEMBER 2022 Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated... - Page 5 Board Layout, Schematic, and Bill of Materials Figure 3-3. Top Layer Figure 3-4. Bottom Layer Figure 3-5. Bottom Solder SLUUCR6 – DECEMBER 2022 BQ25176MEVM Evaluation Module Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated...
- Page 6 Board Layout, Schematic, and Bill of Materials www.ti.com Figure 3-6. Bottom Overlay Figure 3-7. Drill Drawing BQ25176MEVM Evaluation Module SLUUCR6 – DECEMBER 2022 Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated...
-
Page 7: Schematic
82.5k 10.0k 33.0k ISET-ADJ 61.9k 47nF 18.2k 7.50k BIAS 5k Ohm 35.7k SH-JP9 SH-JP8 78B04ST 27.4k 24.3k 18.2k 76SB08ST VSET Figure 3-8. BQ25176EVM Schematic SLUUCR6 – DECEMBER 2022 BQ25176MEVM Evaluation Module Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated... -
Page 8: Bill Of Materials
Electronics Inc Thin Film 27.4kΩ ±1% 0.063W, 1/16W Chip Resistor 0603 (1608 KOA Speer Fitted RN731JTTD2742F50 0603 27.4k Metric) Moisture Resistant Electronics Inc Thin Film BQ25176MEVM Evaluation Module SLUUCR6 – DECEMBER 2022 Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated... - Page 9 (LDO) linear TPS7B8133QDRVRQ1 DRV0006A Instruments Instruments regulator, DRV0006A (WSON-6) CAP, CERM, 100 pF, 50 V, +/- Not Fitted 04025A101FAT2A 0402 100pF 1%, C0G/NP0, 0402 SLUUCR6 – DECEMBER 2022 BQ25176MEVM Evaluation Module Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated...
- Page 10 SH-JP8, SH-JP9 SNT-100-BK-G Samtec Shunt 969102-0000-DA Black Unless otherwise noted in the Alternate PartNumber and/or Alternate Manufacturer columns, all parts may be substituted with equivalents. BQ25176MEVM Evaluation Module SLUUCR6 – DECEMBER 2022 Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated...
-
Page 11: Revision History
4 Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. DATE REVISION NOTES December 2022 Initial Release SLUUCR6 – DECEMBER 2022 BQ25176MEVM Evaluation Module Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated... - Page 12 STANDARD TERMS FOR EVALUATION MODULES Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, and/or documentation which may be provided together or separately (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance with the terms set forth herein.
- Page 13 www.ti.com Regulatory Notices: 3.1 United States 3.1.1 Notice applicable to EVMs not FCC-Approved: FCC NOTICE: This kit is designed to allow product developers to evaluate electronic components, circuitry, or software associated with the kit to determine whether to incorporate such items in a finished product and software developers to write software applications for use with the end product.
- Page 14 www.ti.com Concernant les EVMs avec antennes détachables Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à...
- Page 15 www.ti.com EVM Use Restrictions and Warnings: 4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS. 4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling or using the EVM, including without limitation any warning or restriction notices.
- Page 16 Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief in any United States or foreign court. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2019, Texas Instruments Incorporated...
- Page 17 TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products. TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2022, Texas Instruments Incorporated...
Need help?
Do you have a question about the BQ25176MEVM and is the answer not in the manual?
Questions and answers