Table of Contents
Advertisement
Quick Links
Advertisement
Chapters
Table of Contents
Related Manuals for Beckhoff C9900-U332-0010
Summary of Contents for Beckhoff C9900-U332-0010
- Page 1 Manual | EN C9900-U332-0010 Battery pack 2023-2-10 | Version: 2.2...
-
Page 3: Table Of Contents
Transport and unpacking ........................ 11 Dimensions ............................. 13 Control cabinet installation ...................... 14 Connect battery pack ........................ 17 5 Decommissioning ........................... 19 6 Maintenance ............................ 22 7 Technical data ............................ 23 8 Appendix .............................. 24 Service and support ........................ 24 Approvals ............................ 25 C9900-U332-0010 Version: 2.2... - Page 4 Table of contents Version: 2.2 C9900-U332-0010...
-
Page 5: Notes On The Documentation
Copyright © Beckhoff Automation GmbH & Co. KG. Publication of this document on websites other than ours is prohibited. Offenders will be held liable for the payment of damages. All rights reserved in the event of the grant of a patent, utility model or design. -
Page 6: For Your Safety
Exclusion of liability Beckhoff shall not be liable in the event of non-compliance with this documentation and thus the use of the battery packs outside the documented operating conditions. Description of safety symbols The following safety symbols are used in these operating instructions. -
Page 7: Fundamental Safety Instructions
• the operating instructions are in good condition and complete, and always available for reference at the location where the products are used. C9900-U332-0010 Version: 2.2... -
Page 8: Notes On Information Security
For your safety Notes on information security The products of Beckhoff Automation GmbH & Co. KG (Beckhoff), insofar as they can be accessed online, are equipped with security functions that support the secure operation of plants, systems, machines and networks. Despite the security functions, the creation, implementation and constant updating of a holistic security concept for the operation are necessary to protect the respective plant, system, machine and networks against cyber threats. -
Page 9: Product Overview
Component Description Name plate Information on battery pack equipment 8-pin terminal strip Connecting the battery pack to the power supply unit of the Mounting device Mounting plate with mounting notches for vertical mounting on the DIN rail C9900-U332-0010 Version: 2.2... -
Page 10: Name Plate
Note: here are the symbols applicable to the battery pack such as CE, EAC, UKCA, . The approvals of your battery pack can be found on the name plate and in chapter 9.2 Approvals [} 25]. Reference to safety and warning instructions, power supply and battery leakage protection Version: 2.2 C9900-U332-0010... -
Page 11: Commissioning
1. Check the packaging for transport damage. 2. Remove packaging. 3. Keep the packaging for possible future transport. 4. Check your delivery for completeness by comparing it with your order. 5. Check the contents for visible shipping damage. C9900-U332-0010 Version: 2.2... - Page 12 Commissioning 6. In case of discrepancies between the package contents and the order, or in case of transport damage, please inform Beckhoff Service (see Chapter 8.1 Service and support [} 24]). Version: 2.2 C9900-U332-0010...
-
Page 13: Dimensions
Figure 5 shows the dimensions of the battery pack for horizontal mounting on the DIN rail. Fig. 5: C9900-U332_dimensions horizontal mounting Figure 6 shows the mounting template for mounting without DIN rail. 4x M4 Fig. 6: C9900_U332_mounting without DIN rail C9900-U332-0010 Version: 2.2... -
Page 14: Control Cabinet Installation
1. Loosen the screw of the ground connection plate with a 3.0 mm Allen key (section A). 2. Remove the ground connection plate (section B). 3. Remove the screws of the two mounting notches using a 2.5 mm Allen key (section C). 4. Remove the two mounting notches (section D). Version: 2.2 C9900-U332-0010... -
Page 15: Fig. 7 C9900-U332_Conversion Mounting Plate
1. Place the battery pack on the DIN rail via the rear side (section A). 2. Tighten the four hexagon socket screws of the mounting notches (section B). ð You have installed the battery pack on the DIN rail. Fig. 9: C9900_U332_mounting on DIN rail C9900-U332-0010 Version: 2.2... -
Page 16: Fig. 10 C9900-U332_Mounting Plate
1. Place the battery pack with the marked locations of the mounting plate (see Fig. 10) in front of the pre- pared drill holes. 2. Insert the M4 fastening screws into the drill holes. 3. Tighten the fastening screws. Version: 2.2 C9900-U332-0010... -
Page 17: Connect Battery Pack
Terminal for looping through wires of the supply line to the PC You can connect two wires on each side of a terminal of the terminal strip. For this purpose, you must use double wire end sleeves (see Fig. 12). C9900-U332-0010 Version: 2.2... -
Page 18: Fig. 12 C9900-U332_Double Wire End Sleeve
Battery Power 24 V 24 V DC ext. switch L max = 10 m 1,5 mm / AWG14 Power status UPS Output 24 V DC 24 V/3,4 Ah 30 V/9 A C9900-U332 battery pack Fig. 13: C9900-U332_wiring diagram Version: 2.2 C9900-U332-0010... -
Page 19: Decommissioning
1. Hold the battery pack tightly so that it cannot fall down when the fastening screws are loosened. 2. Remove the fastening screws at the marked points (see Fig. 15). 3. Remove the battery pack from the control cabinet. C9900-U332-0010 Version: 2.2... -
Page 20: Fig. 15 C9900-U332_Mounting Plate
5. Remove the two M3 x 10 screws and the clamp on the front of the battery pack (section E). 6. Pull the angle plate over the front from the housing (section F). Fig. 17: C9900-U332_removal angle plate Version: 2.2 C9900-U332-0010... -
Page 21: Fig. 18 C9900-U332_Removal Of Batteries
You can then dispose of the components as follows: • Dispose of batteries properly. • Send plastic parts (polycarbonate, polyamide (PA6.6)) for plastics recycling. • Take the angle plate to the metal recycling collection point. C9900-U332-0010 Version: 2.2... -
Page 22: Maintenance
• Detergents with scouring or abrasive components • Metal cleaning objects such as razor blades or steel spatulas Repair Only the manufacturer may repair the device. If a repair should be necessary, contact Beckhoff Service (see Chapter 9.1 Service and support [} 24]). Version: 2.2... -
Page 23: Technical Data
Transport and storage The same values for air humidity and shock resistance are to be observed during transport and storage as in operation. The shock resistance during transport can be improved by appropriate packaging of the battery pack. C9900-U332-0010 Version: 2.2... -
Page 24: Appendix
Telephone: + 49 (0) 5246/963-0 Fax: + 49 (0) 5246/963-198 email: info@beckhoff.de The addresses of the worldwide Beckhoff subsidiaries and agencies can be found on our website at http:// www.beckhoff.com/. You will also find further documentation for Beckhoff components there. -
Page 25: Approvals
Appendix Approvals The device has the following approvals: • CE • EAC • UKCA You will find all other applicable approvals on the name plate of your device. C9900-U332-0010 Version: 2.2... - Page 26 C9900-U332_double wire end sleeve ..................Fig. 13 C9900-U332_wiring diagram ....................... Fig. 14 C9900-U332_disassembly from the DIN rail................Fig. 15 C9900-U332_mounting plate ....................... Fig. 16 C9900-U332_removal mounting plate ..................Fig. 17 C9900-U332_removal angle plate ....................Fig. 18 C9900-U332_removal of batteries ....................Version: 2.2 C9900-U332-0010...
- Page 27 List of tables List of tables Table 1 Key for C9900-U332 structure ..................... Table 2 Key for C9900-U332 name plate....................Table 3 Pin assignment terminal strip ....................... C9900-U332-0010 Version: 2.2...
- Page 29 More Information: www.beckhoff.com/c9900-u332 Beckhoff Automation GmbH & Co. KG Hülshorstweg 20 33415 Verl Germany Phone: +49 5246 9630 info@beckhoff.com www.beckhoff.com...