Andis MBG-2 - EasyClip Groom Detachable Blade Clipper Manual

Andis MBG-2 - EasyClip Groom Detachable Blade Clipper Manual

Also See for MBG-2:

Advertisement

Andis MBG-2 - EasyClip Groom Detachable Blade Clipper Manual

USING ATTACHMENT COMBS

(Some models do not have attachment combs)

You can set the blades for a longer cut by using any of the attachment combs made for your Andis clipper. The attachment combs are easy to use–they snap on and off. To attach a comb, slip the attachment onto top edge of blade and snap down onto bottom edge of blade (Figures A & B). The attachment combs help guide the hair to the blades and give you precise control of hair lengths. The length of trim is indicated on each attachment comb.
USING ATTACHMENT COMBS

Use the chart below to find the approximate lengths of cut. Different blade angles in relation to the skin, thickness and texture of the hair will vary the cutting length.

Clipping guide

USER MAINTENANCE

Cleaning and user maintenance shall not be made by children without supervision.

The internal mechanism of your clipper has been permanently lubricated at the factory. Other than the recommended maintenance described in this manual, no other maintenance should be performed, except by Andis Company or an Andis Authorized Service Station.

If the supply cord is damaged it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

REMOVING THE BLADE SET

To remove blade set, first make sure your clipper motor is switched off, then push down on blade with both thumbs (Figure C) and slide blade off blade hinge. If your blade hinge should snap closed and is flush with the clipper, use a small standard screw driver to pry the tongue of the hinge out (Figure D).
REMOVING THE BLADE SET

NOTE: Hair may accumulate in the front cavity of the housing under the blade. If this hap pens, you can clean out the hair by brushing out the cavity with a small brush or an old toothbrush while the blade is off the clipper (see Figure D for location of cavity being referenced).

REPLACING OR CHANGING THE BLADE SET

To replace or change your blade set, slide the blade bracket onto the hinge of the clipper (Figure E) and with the clipper running, push the blade towards the clipper to lock into position.
REPLACING OR CHANGING THE BLADE SET

BLADE TEMPERATURE

Due to the high speed nature of Andis clippers, please check for blade heat often, especially on close cutting blades. If blades are too hot, dip the blades only into Andis Blade Care Plus or apply Andis Cool Care Plus and then Andis Clipper Oil. If you have a detachable blade unit, you can change your blade in order to maintain a comfortable temperature; using multiple blades of the same size is popular among groomers.

CARE AND SERVICING OF YOUR ANDIS CLIPPER BLADES

Blades should be oiled before, during, and after each use. If your clipper blades leave streaks or slow down, it's a sure sign blades need oil. The clipper should be held in the position shown in Figure F to prevent oil from getting into the motor. Place a few drops of Andis Clipper Oil on the front and side of the cutter blades (Figure G). Wipe excess oil off blades with a soft dry cloth. Spray lubricants contain insufficient oil for good lubrication, but are an excellent clipper blade coolant. Always replace broken or nicked blades to prevent injury. You can clean the excess hair from your blades by using a small brush or worn out toothbrush. To clean the blades we suggest to immerse the blades only into a shallow pan of Andis Clipper Oil, while the clipper is running. Any excess hair and dirt that has accumulated between the blades should come out. After cleaning, turn your clipper off and dry blades with a dry cloth and start clipping again.
CARE AND SERVICING - Step 1
CARE AND SERVICING - Step 2

If, upon cleaning your blades, you find the blades will still not cut, there may be a few fine pieces of hair trapped between the upper and lower blade. If this happens, you will need to snap the blade off the clipper. Proceed to slide the upper blade to one side, without loosening the tension spring or moving the upper blade completely out from under the tension spring (Figure H). Wipe the surface between the blades clean with a dry cloth, then place a drop of clipper oil where the upper and lower blades meet and also in the guide slot of the tension spring. Now slide the upper blade to the opposite side of the lower blade and repeat this process. After completing this cleaning procedure, slide the upper blade, centering it over the lower blade. Hang or store your Andis clipper with the blades down so excess oil will not run into the clipper case.
CARE AND SERVICING - Step 3

FACTORY REPAIR SERVICE

When the blades of your Andis clipper become dull after repeated use, it is advised to purchase a new set of blades available through your Andis supplier or through an Andis Authorized Service Station.

CORRECT DISPOSAL OF THIS PRODUCT


This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.


Never handle your Andis clipper while you are operating a water faucet and never hold your clipper under a water faucet or in water. There is danger of electrical shock and damage to your clipper.
The Andis Company will not be responsible in case of injury due to this carelessness.

Item pictured may differ from actual product.

IMPORTANT SAFEGUARDS

When using an electrical appliance, basic precautions should always be followed, including the following: Read all instructions before using the Andis clipper.


To reduce the risk of electric shock:

  1. Do not reach for an appliance that has fallen into water.
    Unplug immediately. Never use clipper near water.
  2. Do not use while bathing or in a shower.
  3. Do not place or store appliance where it can fall or be pulled into a tub or sink. Do not place in or drop into water or other liquid.
  4. Always unplug this appliance from the electrical outlet immediately after using. Unplug by holding and pulling on plug, not cord.
  5. Unplug this appliance before cleaning, removing, or assembling parts.


To reduce the risk of burns, fire, electric shock, or injury to persons:

  1. An appliance should never be left unattended when plugged in.
  2. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
  3. Children shall not play with the appliance.
  4. Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by Andis.
  5. Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the appliance to an Andis Authorized Service Station for examination or repair.
  6. Keep the cord away from heated surfaces.
  7. Never drop or insert any object into any opening.
  8. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
  9. Do not use this appliance with a damaged or broken blade or comb, as injury to the skin may occur.
  10. To disconnect turn control to "0" then remove plug from outlet.

  11. During use, do not place or leave appliance where it may be
    1. damaged by an animal or
    2. exposed to the weather.
  12. Oil blades frequently. Blades may become hot during use.

SAVE THESE INSTRUCTIONS

Please read the following instructions before using your new Andis clipper. Give it the care a fine, precision-built instrument deserves and it will give you years of service. Before starting your clipper, remove blade guard (some models may not have a blade guard). Plug cord into electrical outlet, operate at rated current and cycle as noted on unit. To start clipper move switch button to "1" position; to stop, move switch button back to original position. After using your Andis clipper, rewrap cord, and store in a safe place.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Andis MBG-2 - EasyClip Groom Detachable Blade Clipper Manual

Advertisement

Need help?

Need help?

Do you have a question about the MBG-2 and is the answer not in the manual?

Questions and answers

Table of Contents