FastTt Carbon Aero Bar Installation Manual
Hide thumbs
Also See for Carbon Aero Bar:
- Installation manual (20 pages) ,
- Installation manual (14 pages) ,
- Installation manual (20 pages)
Related Manuals for FastTt Carbon Aero Bar
Summary of Contents for FastTt Carbon Aero Bar
- Page 1 [Designed for Speed] Carbon Aero Bar INSTALLATION GUIDE MODEL: Tri Aero Bar PRE-DRILLED BOLT & RIDE www.FastTT.bike www.fastTT.bike FastTT Aero Bar Installation Guide – Tri Bar...
- Page 2 Before proceeding with installation, we recommend taking a full set of measurements of your current cockpit for reference when installing your aero bars. www.fastTT.bike FastTT Aero Bar Installation Guide – Tri Bar...
-
Page 3: Parts Included
PARTS INCLUDED NOTE: The 4x 16mm bolts should ONLY be used when mounting our BTA bottle bracket between the bar bracket and adjustable angled riser. www.fastTT.bike FastTT Aero Bar Installation Guide – Tri Bar... - Page 4 Trimming the bar ends to the correct must be completed before moving to the next step. Examples of various shifter types fitted to the aero bars, showing different bar height/length setup options to suit individual athlete preference www.fastTT.bike FastTT Aero Bar Installation Guide – Tri Bar...
- Page 5 SECTION B – MOUNTING THE BARS SECTION D – MOUNTING THE BARS Placement options FastTT aero bars offer a wide range of bolt holes and bracket placement options for you to find your preferred setup. Fitting adjustable angled risers If fitting FastTT adjustable angled risers, bolt the bottom blocks of the risers to your base bar or spacer stack.
- Page 6 Fitting the mounting brackets to FastTT angled riser and Profile Design brackets Using the supplied M5 button head bolts, attach the bracket to the top block of the FastTT Adjustable angled riser or to the Profile Design wing bracket, depending on the mounting option you selected.
- Page 7 Dremel. Unless you ordered FastTT long bolts you will need to provide the correct length and thread diameter bolts for your bike. Tighten the bolts to the torque specified by the bolt supplier or your owner’s manual.
- Page 8 We also stock a comprehensive range of long mounting bolts: https://www.fasttt.bike/product-category/mounting-bolts/ If you are using the FastTT adjustable angled riser, or our spacers, they have a channel in the rear to fit the shifter wires.
- Page 9 If necessary, use the curve of the cable to assist in guiding the draw wire into the bar tube. www.fastTT.bike FastTT Aero Bar Installation Guide – Tri Bar...
- Page 10 For older Di2 shifters where the cable inserts from outside the bar tube, the draw wire is fed from the opposite direction i.e. feed it into the hole at the base of the bar end tube and out the rear hole. www.fastTT.bike FastTT Aero Bar Installation Guide – Tri Bar...
- Page 11 To route the shifter wire, insert it down an unused open hole or over the back edge of the bar, and route it to the junction box. Fix the wire into the channel in the adjustable angled riser, or FastTT spacers. www.fastTT.bike FastTT Aero Bar Installation Guide – Tri Bar...
- Page 12 SECTION C - CABLE INSTALLATION FOR ELECTRONIC SHIFTERS Fit the rubber grommet around the shifter wire and insert it into the shifter exit hole. Re-install the foam elbow pads. www.fastTT.bike FastTT Aero Bar Installation Guide – Tri Bar...
- Page 13 Route the shifter cable to the derailleur according to the most efficient route. Try to keep the cable as close to the frame as possible for maximum aero efficiency. Insert the shifters and tighten according to the manufacturer’s instructions. SECTION D – MOUNTING THE BARS www.fastTT.bike FastTT Aero Bar Installation Guide – Tri Bar...
-
Page 14: Important Service Note
IMPORTANT SERVICE NOTE! After a few rides we recommend that you check and retighten the mounting bolts on your FastTT Aero Bars. The bolts can become slightly loose after initial riding due to natural bedding in of the bolts into the carbon mounting base. -
Page 15: Section F - Warranty And Disclaimer
SECTION F – WARRANTY AND DISCLAIMER WARRANTY FastTT Aero Bars are lightweight carbon competition units. In the event of a fall or harsh impact, please check the bars carefully for any visible damage. Whilst carbon fibre is exceptionally strong, it does not tolerate impacts, and damage that is invisible to the naked eye can occur.