Advertisement
Quick Links
Advertisement
Related Manuals for 2K Furniture Designs C1274
Summary of Contents for 2K Furniture Designs C1274
- Page 1 ASSEMBLY INSTRUCTIONS Page 1 of 11...
- Page 2 To insert a cam lock: (Please read below instructions before assembling) Diagram A 1. Insert cam screw into hole as shown in diagram A . Diagram B Make sure not to insert the cam screw: Too deep as shown in figure B as this will cause the cam screw to be misaligned and unable to interlock properly.
-
Page 3: Part List
Part List Quantity Quantity Quantity Quantity of 1 of 1 of 1 of 1 Top Panel Bottom Shelf Divider Panel Side Panel(Left) Quantity Quantity Quantity Quantity of 1 of 1 of 1 of 1 Center Divider Side Panel(Right) Door(Left) Door(Right) Quantity Quantity Quantity... -
Page 4: Hardware List
Hardware List Quantity Quantity Quantity Quantity of 22 of 28 of 2 of 22 Cam-Lock Wood Dowel Bolt Screw Quantity Quantity Quantity Quantity of 4 of 2 of 1 of 4 Magnet with Screw Connect Block Connect Plate with Screw Door Pin Quantity Quantity... - Page 5 Page 5 of 11...
- Page 6 Step1: 2pcs 2pcs Assemble Divider (5) to Divider Panel (2) using Bolts (C) and Wood Dowels (B) as shown above. 6sets Step 2: 6pcs Assemble Rear Legs (14&15 ) to Side Panels (4&6) and Connect Bars (11) using Cam-Locks (A) and Wood Dowels (B) as shown above.
- Page 7 Step 3: 4sets 4pcs 2pcs 4pcs Assemble Divider Panel (2) to Side Panels (4&6) using Cam-Locks (A) and Wood Dowels (B) as shown above. Assemble Connect Block (E) to Rear Legs (14&15 ) using Screws (D) as shown above. Step 4: 4pcs Assemble Bottom Shelf (3) to Rear Legs (14&15) using Screws (D) as shown above.
- Page 8 6sets Step 5: 6pcs 2pcs 8pcs Fig.1. 1). Assemble Connect Blocks (E) to Front Legs (12&13) using Screw(D) ,refer t o Fig.1. 2). Then assemble Front Legs (12&13) to Side Panels (4&6) , Bottom Shelf (3) and Connect Bars (11) using Cam-Locks (A) Wood Dowels (B) and Screws (D) as shown above.
- Page 9 Step 7: 2sets 1set 1). Attach Magnets (F) to the bottom of Top Panel (1) using included Screws (F) as shown above. 2).Attach Connect Plate (G) to the bottom of Top Panel (1) using included Screws(G). Step 8: 6pcs 10pcs 14pcs Assemble Top Panel (1) to Legs (12&13&14&15) and Divider (5) Side Panels (4&6) using Wood Dowels (B) and Cam-Locks (A) as shown above.
- Page 10 Step 9: 4pcs 2sets Insert Door Pins (H) into the hole on the two ends of Door Panels (7&8). Then attach Door Handles (I) to Door Panels (7&8) using included bolts (I). Step 10: Fig.2. Fig.1. Connect Door Panels (7&8) to Divider Panel (2) as drawing Fig.1. Then press down Door Pin (H) ( see Fig.2.) and hold the Door Panel carefully into the cabinet with the upper pin popping up into the hole of Top Panel (1).
- Page 11 Step 11: 6pcs 6pcs Attach Connect Blocks (J) to Rear Legs (14 &15) ,Divider (2) and Top Panel (1) to hold Back Panels (9&10) using Screws (D) as shown above. Step 12: 1set wall wall For your safety, please attach this unit to the wall by Anchor with Screws ( K). Page 11 of 11...