Related Manuals for Planet Networking & Communication MGS-910X
Summary of Contents for Planet Networking & Communication MGS-910X
- Page 1 8-Port 10/100/1000/2500T + 1-Port 10G SFP+ Multigigabit Ethernet Switch 8-Port 10/100/1000/2500T 802.3at PoE+ + 1-Port 10G SFP+ Multigigabit Ethernet Switch (120 Watts) MGS-910X/MGS-910XP User’s Manual...
-
Page 2: Table Of Contents
Table of Contents 1. Package Contents ................. 3 2. Hardware Introduction ................4 2.1 Front Panel ................... 4 2.2 LED Indicators ................4 2.3 Multiple Functions of DIP Switch ............. 5 2.4 Switch Rear Panel ................7 3. Hardware Installation ................8 3.1 Rack Mounting ................ -
Page 3: Package Contents
Thank you for purchasing PLANET 8-Port 10/100/1000/2500T Multigigabit Ethernet Switch, MGS-910X or MGS-910XP. “Multigigabit Ethernet Switch” mentioned in this User’s Manual refers to the MGS-910X or MGS-910XP. Open the box of the Multigigabit Ethernet Switch and carefully unpack it. The... -
Page 4: Hardware Introduction
The Front Panel of the Multigigabit Ethernet Switch consists of 8 auto-sensing 10/100/1000/2500Mbps Ethernet RJ45 ports and 1 10GBASE-X SFP+ slot. The LED Indicators are also located on the front panel of the Multigigabit Ethernet Switch. MGS-910X 8-Port 10/100/1000/2500T + 1-Port 10G SFP+ Multigigabit Ethernet Switch 2.5G... -
Page 5: Multiple Functions Of Dip Switch
10GBASE-X SFP+ Port Color Function Lights to indicate the link through that port is established successfully at 10Gbps. LNK/ACT Green Blinks to indicate that the Switch is actively sending or receiving data over that port. 802.3at PoE+ TP Interface (MGS-910XP) Color Function Lights to indicate that the port is providing PoE... -
Page 6: Switch Rear Panel
2.5G IP Camera MGS-910XP 10GBASE-SR/LR Fiber Optic 2.5G UTP with PoE 2.5G 1000BASE-T UTP 2.4 Switch Rear Panel Figure 2 shows the rear panel of the MGS-910X/910XP MGS-910X 100-240V , 1A max. 50/60Hz MGS-910XP 100-240V , 3A max. - Page 7 AC Power Receptacle The device is a power-required device, which means it will not work till it is powered. If your networks should be active all the time, please consider using UPS (uninterrupted power supply) for your device. It will prevent you from network data loss or network downtime.
-
Page 8: Hardware Installation
3. Hardware Installation This part describes how to install your Multigigabit Ethernet Switch and make connections to it. Please follow the procedure below: This Multigigabit Ethernet Switch does not need software config- uration. 3.1 Rack Mounting To install the Multigigabit Ethernet Switch on the desktop, simply follow these steps: Step 1: Attach the rubber feet to the recessed areas on the bottom of the Multigigabit Ethernet Switch. -
Page 9: Rack Mounting
Step 5: Supply power to the Multigigabit Ethernet Switch. A. Connect one end of the power cable to the Multigigabit Ethernet Switch. B. Connect the power plug of the power cable to a standard wall outlet. When the Multigigabit Ethernet Switch receives power, the Power LED should remain solid Green. -
Page 10: Installing The Sfp+ Transceiver
8-P ort 10/ 100 /10 00/ Mu ltig iga 250 0T 802 bit Eth ern .3a t PoE+ et Sw itch + 1-P ort 10G SFP + 2.5G 10/10 0/100 LNK/A CT 0 LNK/A PoE-i n-Use MG S-91 0XP Stand ard LNK/A CT VLAN 10G SFP+... - Page 11 It is recommended to use PLANET SFP+ on the Multigigabit Ethernet Switch. If you insert an SFP+ transceiver that is not supported, the Multigigabit Ethernet Switch will not recognize it. 10GBASE-X SR/LR: Before connecting the other switches, workstation or media converter, please do the following: 1.
- Page 12 MTB-Series SFP+ Transceiver LC Fiber Cable Figure 6: Pulling Out from the Transceiver Never pull out the module without pulling the lever or the push bolts on the module. Directly pulling out the module with effort could damage the module and SFP+ module slot of the Multi- gigabit Ethernet Switch.
-
Page 13: Product Specifications
4. Product Specifications Product MGS-910X MGS-910XP Hardware Specifications 10/100/1000/2500BASE-T Copper Interfaces 10GBASE-X SFP+ interface Selectable operation Selectable operation mode mode DIP Switch Standard Standard VLAN VLAN System System Power (Green) Power (Green) 10/100/1000/2500T RJ45 10/100/1000/2500T RJ45 Interfaces Interfaces ... - Page 14 Switching Switch Architecture Store-and-Forward Store-and-Forward Switch Fabric 60Gbps 60Gbps Switch 44.64Mpps 44.64Mpps Throughput@64bytes MAC Address Table 4K entries 4K entries Jumbo Frame IEEE 802.3x pause frame IEEE 802.3x pause frame Flow Control for full duplex; back for full duplex; back pressure for half duplex pressure for half duplex Power over Ethernet...
- Page 15 Standards Conformance Regulatory Compliance FCC Part 15 Class A, CE FCC Part 15 Class A, CE IEEE 802.3 (Ethernet) IEEE 802.3 (Ethernet) IEEE 802.3u IEEE 802.3u (Fast Ethernet) (Fast Ethernet) IEEE 802.3ab IEEE 802.3ab (Gigabit Ethernet) (Gigabit Ethernet) IEEE 802.3bz IEEE 802.3bz (2.5Gigabit Ethernet) (2.5Gigabit Ethernet)
-
Page 16: Physical Dimensions
5. Physical Dimensions The MGS-910X dimensions (W x D x H): 280 x 180 x 44mm 8-Port 10/100/1000/2500T+1-Port 10G SFP+ Multigigabit Ethernet Switch 2.5G LNK/ACT 10/100/1000 LNK/ACT 10G SFP+ LNK/ACT Standard MGS-910X VLAN Unit: mm... - Page 17 The MGS-910XP dimensions (W x D x H): 280 x 180 x 44mm 8-Port 10/100/1000/2500T 802.3at PoE++1-Port 10G SFP+ Multigigabit Ethernet Switch 2.5G LNK/ACT 10/100/1000 LNK/ACT 10G SFP+ PoE-in-Use LNK/ACT MGS-910XP Standard VLAN Unit: mm...
-
Page 18: Customer Support
Customer Support Thank you for purchasing PLANET products. You can browse our online FAQ resource on PLANET Web site first to check if it could solve your issue. If you need more support information, please contact PLANET support team. PLANET online FAQs: https://www.planet.com.tw/en/support/faq Support team mail address: support@planet.com.tw...
Need help?
Do you have a question about the MGS-910X and is the answer not in the manual?
Questions and answers